AL175ULX Two (2) Output Switching Power Supply


1.75 amp supply current. • Two (2) Class 2 Rated power limited outputs. - Fail-Safe/Fail-Secure lock output (switched). - Auxiliary power output (unswitched).

AL175ULX Two (2) Output Switching Power Supply/Charger Rev. DSAL175ULX - 10192012

Overview AL175ULX is a Two (2) Output Switching Power Supply/Charger that converts a 115VAC 60Hz input, into two (2) individually PTC protected 12VDC or 24VDC outputs.

AL175ULX

Specifications Supervision:

Input: • Input 115VAC, 60Hz, 0.6 amp. • Access control trigger input.

• AC fail supervision (form “C” contacts). • Supervised Fire Alarm Disconnect (Latching w/reset or Non-Latching).

• 12VDC or 24VDC selectable outputs. • 1.75 amp supply current. • Two (2) Class 2 Rated power limited outputs. - Fail-Safe/Fail-Secure lock output (switched). - Auxiliary power output (unswitched). • PTC protected outputs, rated @ 2.5 amp. • Filtered and electronically regulated output. • Short circuit and thermal overload protection.

Visual Indicators:

Output:

Battery Backup: • Built-in charger for sealed lead acid or gel type batteries. • Automatic switch over to stand-by battery when AC fails. • Maximum charge current 0.4 amp.

• AC input and DC output LED indicators.

Electrical:

• Operating temperature: 0º C to 49º C ambient. • 10.75-21.5 BTU/Hr. • System AC input VA requirement: 69VA.

Mechanical: • Enclosure Dimensions (H x W x D approx.): 13.5” (342.9mm) x 13” (330.2mm) x 3.25” (82.55mm) - Accommodates up to two (2) 12VDC/7AH batteries. • Product weight (approx.): 8.4 lbs. (3.81 kg.). • Shipping weight (approx.): 9.4 lbs. (4.26 kg.).

Agency Approvals UL 294

UL Listed for Access Control System Units.

MEA - NYC Department of Buildings Approved. Altronix Corp.

140 58th St. Brooklyn, NY

CUL Listed - CSA Standard C22.2 No.205-M1983, Signal Equipment.

CSFM - California State Fire Marshal Approved.

Enclosure Dimensions (H x W x D) (approximate): 13.5” (342.9mm) x 13” (330.2mm) x 3.25” (82.55mm) 1.40” (36mm)

4.85” (123mm)

4.85” (123mm)

1.40” (36mm)

1.20” (31mm) 3.25” (83mm)

1.20” (31mm)

0.75” (19mm)

12.5” (318mm) 11.0” (279mm)

1.20” (31mm)

0.75” (19mm) 0.9375” (24mm)

1.40” (36mm)

1.40” (36mm)

5.10” (130mm)

5.10” (130mm)

13.0” (330mm)

5.10” (130mm) 6.5625” (167mm)

0.9375” (24mm)

3.25” (83mm)

3.25” (83mm) 3.25” (83mm)

1.0” (25mm)

1.0” (25mm)

1.0” (25mm)

10.5” (267mm)

Altronix Corp. - 140 58th Street, Brooklyn, NY 11220 • 718-567-8181 • 888-258-7669 • altronix.com

1.0” (25mm)

Recommend Documents
Thermal runaway o. Reverse battery hookup. • Class 2 power limited output with a green LED status indicator. • Fuse protected against surge for AC input and ...

140 58th Street, Brooklyn, NY 11220 • 718-567-8181 • 888-258-7669 • altronix.com. 1.40”. (36mm). 1.40”. (36mm). 4.85”. (123mm). 4.85”. (123mm). 1.40”.

desired, use an optional bushing, grommet or another sleeve to protect wires passing through the hole(s). 3. If desired, a cam lock (not included) can be installed ...

The RadioShack 22-510 Switching Power Supply provides AC to DC conversion to mimic a car's electrical system. This teardown looks at some of the components that make this supply function. FERRAMENTAS: Phillips #1 Screwdriver (1). Adjustable Wrench (1

GROUND THE INSTRUMENT. To minimize shock hazard, the instrument chassis and cabinet must be connected to an electrical ground. This instrument is grounded through the ground conductor of the supplied, three-conductor ac power cable. The power cable m

All rights reserved including the right of reproduction in whole or in part in any form. www.extech.com. Single power supply with multiple DC outputs. 6/5/08 - R2.

Green LED on the circuit board will illuminate when power is present. 8. Upon completion of wiring, secure enclosure door with screws (supplied). WARNING: To ... 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site:

Connect each DC device to terminal pairs on DC output board 1 thru 8, marked [P (+) and N (-)] carefully observing correct polarity. Connect each AC device to terminal pairs on AC output board 1 thru 8, marked [P (+) and N (-)]. 6. When batteries are

draw the circuit diagram for a phase control circuit, using a. RC network and a diac;. ☑ draw and analyse graphs that show the phase difference between.

Jun 20, 2013 - fluorescent ballasts, and neon/cold cathode lighting sources. .... If combining dimmed and switched lighting on the same AFCI circuit, the ...