INSTALLATION INSTRUCTIONS


The ADJUSTABLE SHOWER BAR (1) works best if secured to a wall stud or cross brace within the wall, using the MOUNTING. SCREWS (2) supplied.

INSTALLATION INSTRUCTIONS Percy Personal Hand Shower with Adjustable Wall Mounted Bar ®

ModelD35105780

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing supply stores. It is essential that the tools and materials be on hand before work is begun.

Teflon Tape

Drill

Adjustable Wrench

F U T U R E

RECOMMENDED TOOLS AND MATERIALS

U S E

Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin.

In the United States: DXV One Centennial Avenue Piscataway, New Jersey 08855 Attention: Director of Customer Care For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 227-2734 www.DXV.com

Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2017

Flat Blade Screwdriver

In Canada: DXV 5900 Avebury Road Mississauga, Ontario L5R 3M3 Canada Toll Free: 1-800-387-0369 Local: 905-306-1093 Fax: 1-800-395-1498 www.DXV.ca

-1-

Level

In Mexico: DXV Via Morelos 330 Col. Santa Clara Coatitla Ecatepec, Estado de México 55540 Toll Free: 01-800-8391200 www.DXV.mx

M965532 Rev. 1.4 (5/17)

S A V E

Plumbers' Putty or Caulking

F O R

Phillips Screwdriver

ROUGHING-IN DIMENSIONS: • For reference 3-7/16" (87 mm)

1-1/16" (27 mm)

1/2" (13 mm)

WALL SUPPLY WITH BUILT IN BACK FLOW PREVENTER

1/2" (13 mm) N.P.T.

23-5/8" (600 mm)

1-7/16" (37 mm)

48" - 60" (1219 - 1524 mm) (OPTIONAL) TO FINISHED FLOOR

1/2 (13 mm) NPSM HOSE CONNECTION (WITH CHECK VALVE) RUBBER GASKET

25-9/16" (650 mm)

FINISHED WALL

1-7/16" (36 mm)

1" (25 mm)

8" (204 mm) 59" (1498 mm) 2-1/4" D. (57 mm)

2-7/8" (73 mm)

1/2" (13 mm) NPSM HOSE CONNECTION (WITH CHECK VALVE)

FINISHED WALL

2

1 INSTALL WALL SUPPLY CAUTION

Turn off hot and cold water supplies before beginning.

• Supply to WALL SUPPLY (1) is 1/2" (13 mm) NPT. See rough-in above for detailed information. • Install RUBBER SEAL (2) onto WALL SUPPLY (1). • Apply sealant or teflon tape to threads of 1/2" (13 mm) NPT supply nipple. Thread WALL SUPPLY (1) onto supply nipple making a water tight seal. WALL SUPPLY (1) with RUBBER SEAL (2) should be tight against finished wall. 2 1

INSTALL WALL BRACKETS • The ADJUSTABLE SHOWER BAR (1) works best if secured to a wall stud or cross brace within the wall, using the MOUNTING SCREWS (2) supplied. • If the ADJUSTABLE SHOWER BAR (1) is to be installed on a tile or plaster wall the ANCHORS (3) and SCREWS (2) should be used. • Determine desired height and location (optional) of the top MOUNTING PLATE (4). NOTE: MEASURMENT IS APPROXIMATE ONLY, PLEASE USE BAR AS TEMPLATE FOR ACTUAL CENTER TO CENTER MEASUREMENTS. Use a level to make sure the center line between the two MOUNTING PLATES (3) is vertical. If the MOUNTING PLATES (3) are secured to a stud or cross brace, drill small pilot holes for SCREWS (2). • For installations on drywall or tiled walls: Use ANCHORS (3) and SCREWS (2) for securing MOUNTING PLATE (4) to finished wall. Drill six 1/4" dia. holes a minimum of 1-3/4" deep. Insert the ANCHORS (4) flush with face of the finished wall.

1/2" NPT APPLY SEALANT

• Secure MOUNTING PLATES (4) to wall with SCREWS (2).

-2-

M965532 Rev. 1.4 (5/17)

3 INSTALL ADJUSTABLE SHOWER BAR • Install the ADJUSTABLE SHOWER BAR (1) onto the MOUNTING BRACKETS (4). Push ADJUSTABLE SHOWER BAR (1) flush against finished wall and tighten SET SCREWS (5) with HEX WRENCH (6) supplied with accessory.

6 5

*C/L

2

1

OPTIONAL TO FINISHED FLOOR

3

4

LEVEL

11 FINISHED WALL

2

9

*23-5/8" (600mm)

1

10

4 3 9 7 8

4 7 *C/L

5 6

4 INSTALL HOSE AND HAND SHOWER • Install SEAL (7) into COUPLING NUT (8). Connect COUPLING NUT (8) to WALL SUPPLY NIPPLE (9) and tighten. • INSTALL second SEAL (9) into SPRAY HOSE END (10) and connect HAND SHOWER (11) to SPRAY HOSE END (11a). Hand tighten.

5

*FROM CENTER TO CENTER OF WALL BRACKETS *NOTE: MEASURMENT IS APPROXIMATE ONLY, PLEASE USE BAR AS TEMPLATE FOR ACTUAL CENTER TO CENTER MEASUREMENTS.

TEST INSTALLED HAND SHOWER • Lift HAND SHOWER (1) from HOLDER (2) and direct spray into tub. Turn hand shower valve on to check HAND SHOWER (1) for proper operation and hose connections for leaks. • Use KNOB (3) on HOLDER (2) to adjust HAND SHOWER (1) height on slide bar.

-3-

1

2

3

M965532 Rev. 1.4 (5/17)

Percy

®

Personal Hand Shower with

Adjustable Wall Mounted Bar MODEL NUMBER

D35105780 Replace the “YYY” with appropriate finish code POLISHED CHROME

100

BRUSHED NICKEL

144

M964655-0070A MOUNTING KIT

D35105781.XXX HAND SHOWER H960440.XXX HOSE & SEALS

D35700035.XXX WALL ELBOW

M964561-YYY0A HAND SHOWER BRACKET

M964547-0070A SET SCREW

-4-

M965532 Rev. 1.4 (5/17)

Recommend Documents
Feb 7, 2017 - SURFACE MOUNT EDGE-LIT LED EXIT SIGN ... the switch is released, EXIT section remains ON and the LED indicator turns back to RED.

If you have any questions, please call our customer service line at ... Insert the end of the misting line into the faucet connector for about 1/2 in. to 5/8 in. by.

Feb 7, 2017 - Plug remaining holes with the appropriate color plugs. ... Run connection wires through large hole between mounting holes C ... WHITE COMM.

Installation & Setup. Mount the appropriate 11 pin octal socket (Macromatic 70170-D or. Custom Connector OT11-PC) in a suitable enclosure. Wire the socket.

FINIAL/CAP ASSEMBLY, HEX NUT, and. LOCKWASHER. Then carefully lift the. CAGE ASSEMBLY, tilting it at an angle to clear the bulbs and LAMPHOLDERS.