Tamper Switch Thermal Kit Ground Terminal
TX3 Aperio Door Controller Installation Quick Reference
Inputs 1 to 8
Outputs 1 to 6 SW1
Inputs 1 to 8 are general purpose inputs.
Aperio Hub Settings and Connections
SW1 sets the Telephone Access controller networkSwitch address. Use Tamper DIP switches 1 to 5 to set the network address. DIP switches 6, 7 and 8 should remain at the factory set values.
• Set DIP switches 1 to 4 on S101 to a unique RS-485
address. • Set DIP switch 8 on S101 to ON if the Aperio hub is
INPUT 1
INPUT 8
on the end of the RS-485 bus.
SW2
OUTPUT 7
JW4
hubs on the RS-485 network.
NO NC
OUTPUT 1
OUTPUT 2
JW6
terminal on the MD-1113.
DIP
D0 RED
ON
GREEN
1 2 3 4 5 6 7 8 9 10
INT
Aperio USB connection Hub 1
TERM UP DOWN A4 A3 A2 A1 A0
OUTPUT 6
Outputs 7 and 8 Outputs 7 and 8 are programmable and provide:
P6 - P5 +OFF BAT-
INPUT
BAT+
JW1 OPEN JW2 OPEN - S +
-
SW2 Aperio Hub 3
Ribbon cable connects to P3 on main board ON
ON/OFF A BSwitch SW1
SW2 sets the Card Access controller RS-485 network address and determines how the IP module get its IP address (if installed).
• Use DIP switches 1 to 6 to set the RS-485 network address. A B
Connection for front door LEDs
Address 1
Red
12 V BATTERY
P5, P6. Battery connections. P7. AC, Trouble and Alarm LEDs.
Jumpers
MD-1113 Module
JW1, JW2. Leave open. Short only when updating firmware. JW3, JW4, JW5. Leave open. Not used.
Aperio Hub 1
A B
JW1 OPEN JW2 OPEN
S101 DIP 6 OFF DIP 7 OFF DIP 8 OFF
Aperio Hub 2
Aperio Hub 3
A B
A B
S101 DIP 6 OFF DIP 7 OFF DIP 8 OFF
S101 DIP 6 ON DIP 7 ON DIP 8 ON
Connect the last controller on the network to the RS-485 input terminal. Refer to LT-980 section 3.3.5 for end of line resistors to be used on the first and last nodes of network. The RS-485 terminal consists of + (positive), - (negative), and S (Shield) connections. Aperio Hub 3
A B
A B
A B
S101 DIP 6 ON DIP 7 ON DIP 8 ON
S101 DIP 6 OFF DIP 7 OFF DIP 8 OFF
S101 DIP 6 OFF DIP 7 OFF DIP 8 ON
JW1 OPEN JW2 OPEN
JW6. JW6 is not used and by default is open. Version 0.11 LT-1164
Aperio Hub 2
Aperio Door Controller Installation Quick Reference
OFF
The RS-485 connection consists of an input and output terminal. Connect the RS-485 output terminal to the RS-485 input terminal of the next controller.
16 Guage Wire
MD-1113 Module
8
RS-485
Aperio hubs on both ends of RS-485 bus. Aperio Hub 1
ON
software.
Connecting the Aperio Hubs to the MD-1113 RS-485 Network Terminal MD-1113 on one end and an Aperio hub on the other end of the RS-485 network bus.
Address 4
• Set DIP switch 8 ON to get IP address from TX3 Configurator
P3. Connector for MD-1113 Module Board. P4. Connector for MD-921 IP Module board.
Address 3
• Set DIP switch 8 OFF to get IP address from DHCP server.
Ground Terminal
optional
Address 2
S101 DIP 6 OFF DIP 7 OFF 1 8 1 8 1 8 1 DIP 8 ON • Keep DIP switch 7 at the factory set value
Power terminals for 16 Vac transformer (PS-4 or PS-4P)
+
USB. Computer connection for firmware download and configuration.
output of 1 A. For example, if output 7 provides 700 mA, then output 8 provides 300 mA.
S +
-
Connections
• a maximum output of 700 mA each, for a combined total
S101 DIP 6 OFF DIP 7 OFF DIP 8 OFF
OUTPUT
Black
J100
• 12 Vdc
P7 Aperio Hub 2
P1
RS-485
Thermal Kit
8-24VDC
• 30 Vac rated \ 1 amp
NO
MD-1113
RS-485 terminals for connecting to multiple TX3 controllers
S101
OUTPUT 5
C
ALARM
JW 1
S101 DIP 6 ON DIP 7 ON DIP 8 ON
EXT
• 30 Vdc \ 3 amp
NO NC
TROUBLE
Connection to 12V battery backup Module MD-1113
A B
ANTENNA
OUTPUT 4
C
LEDs
JW 5
A
NO NC
RS-485 terminals for Aperio Hubs (see figures below)
terminal on the MD-1113. 8-24VDC terminals on J100.
OUTPUT 3
C
P4
• Connect the B terminal on J100 to the negative (-) • Connect power (8-24 Vdc, 250 mA) to the GND and
NO NC
AC
JW2
• Connect the A terminal on J100 to the positive (+)
C
Outputs 7 and 8 IP Module Interface
hubs on the RS-485 network.
NO NC
C
O u ttpu p u t s 1 to 6
JW3
• Set DIP switch 7 on S101 to ON for one of the Aperio
GND
OUTPUT 8
C
Inputs 1 to 8
• Set DIP switch 6 on S101 to ON for one of the Aperio
D1
NC
12V
12V
B
Outputs 1 to 6 are relay contact programmable normally open (NO) or normally closed (NC) outputs. Any power supply connected to these outputs cannot exceed:
Ground Terminal The Card Access system is equipped with a 16 gauge electrical wire attached to the panel chassis Ground Terminal. Do not disconnect this wire. Attach the end of the supplied wire to a suitable grounding wire 16 gauge or thicker. Attach the other end to the cold water ground.
for more information see LT-1160 Aperio Door Controller System Manual available on CD, USB flash drive, or website WWW.MIRCOM.COM
TX3 Aperio Door Controller Installation Quick Reference
The following figure shows the various controller connections
Aperio Hub 1
Aperio Hub n
TX3 Aperio™ Door Controller Installation Quick Reference IMPORTANT This document is for reference only and does not replace the existing documentation. For more detailed information refer to the documentation on the CD, the USB flash drive, or Mircom website (www.mircom.com).
RS-485 Network for Aperio Hubs Maximum network bus length: 3,000 feet Use 22 AWG wire
Installation Prerequisites OUTPUTS 1 to 6
INPUTS 1 to 8
Relay contact, 2 amps
General purpose inputs General purpose input
General purpose input
1 pair 22 AWG
General purpose input
1 pair 22 AWG
1 pair 22 AWG
• Ensure there is a provision for a ground circuit. The Aperio Door Controller assembly must be grounded by a qualified
electrician. An improperly grounded unit can result in equipment malfunction and void the warranty. • Use the latest Aperio Door Controller System controller firmware. Mircom periodically updates panel firmware and
Configurator Software to add features and correct any minor inconsistencies. For information about the latest firmware or software visit the ‘Manuals and Downloads’ section of the Mircom website at www.mircom.com.
Aperio Door Controller
Basic Wiring
3 wires 22 AWG
1. Turn the controller power switch to OFF. 2. Connect the Aperio hub network bus to the RS-485 terminal on the MD-1113 Module board. 3. Connect any inputs and outputs. 1 pair 22 AWG
1 pair 18 AWG 1 pair 22 AWG
General purpose input
General purpose input
OUTPUTS 7 to 8
22 AWG
Programmable outputs Combined 1 amp output 12 Vdc 500 mA
Power transformer 16VAC/40VA PS-4 or PS-4P
Power transformer AC or DC Door strike supply
Configure the system using the Configurator software using a USB or modem connection. Verify the following: • Ensure that the controller and all connected devices and components are fully operational.
• Ensure the Configurator software is set with the correct controller RS-485 network address. 120 VAC 60HZ
Wiring requirements • Install all transformers outside the Lobby Control Unit enclosure. • Unless specified otherwise, all wiring is a maximum length of 1000 ft. The RS-485 wiring maximum length is 4000 ft. • All units use the PS-4P transformer for the power supply. The door strike power supply depends on the door strike
Version 0.11 LT-1164
Before Starting the Configuration
• Ensure the controller DIP Switches are set with a unique RS-485 network address.
Single Panel Wiring
power requirements.
5. Set SW2 to a unique RS-485 network address. 6. Turn the controller power switch to ON (a correctly wired controller will show a green AC LED).
RS-485 Network for TX3 devices
Electrical room
4. Connect the controller supply.
• Ensure that your PC is set with the correct date and time.
To Start the Configuration 1. Connect the PC to the controller using the USB port or modem connection. 2. Launch the Configurator and select the correct controller you are connecting to (on the basis of name, panel label, panel model, and network address). 3. Click Connect. The connection icon appears in the Configurator tool bar. 4. Ensure that the panel is configured with the correct date and time. 5. Configure the Aperio Door Controller using the instructions in the LT-1160 Installation and Operation Manual. for more information go to the CD, USB flash drive, or website and read the LT-1160 Aperio Door Controller System Manual WWW.MIRCOM.COM
Inputs 1 to 8
Outputs 1 to 6 SW1
Inputs 1 to 8 are general purpose inputs.
Aperio Hub Settings and Connections
SW1 sets the Telephone Access controller networkSwitch address. Use Tamper DIP switches 1 to 5 to set the network address. DIP switches 6, 7 and 8 should remain at the factory set values.
• Set DIP switches 1 to 4 on S101 to a unique RS-485
address. • Set DIP switch 8 on S101 to ON if the Aperio hub is
INPUT 1
INPUT 8
on the end of the RS-485 bus.
SW2
OUTPUT 7
JW4
hubs on the RS-485 network.
NO NC
OUTPUT 1
OUTPUT 2
JW6
terminal on the MD-1113.
DIP
D0 RED
ON
GREEN
1 2 3 4 5 6 7 8 9 10
INT
Aperio USB connection Hub 1
TERM UP DOWN A4 A3 A2 A1 A0
OUTPUT 6
Outputs 7 and 8 Outputs 7 and 8 are programmable and provide:
P6 - P5 +OFF BAT-
INPUT
BAT+
JW1 OPEN JW2 OPEN - S +
-
SW2 Aperio Hub 3
Ribbon cable connects to P3 on main board ON
ON/OFF A BSwitch SW1
SW2 sets the Card Access controller RS-485 network address and determines how the IP module get its IP address (if installed).
• Use DIP switches 1 to 6 to set the RS-485 network address. A B
Connection for front door LEDs
Address 1
Red
12 V BATTERY
P5, P6. Battery connections. P7. AC, Trouble and Alarm LEDs.
Jumpers
MD-1113 Module
JW1, JW2. Leave open. Short only when updating firmware. JW3, JW4, JW5. Leave open. Not used.
Aperio Hub 1
A B
JW1 OPEN JW2 OPEN
S101 DIP 6 OFF DIP 7 OFF DIP 8 OFF
Aperio Hub 2
Aperio Hub 3
A B
A B
S101 DIP 6 OFF DIP 7 OFF DIP 8 OFF
S101 DIP 6 ON DIP 7 ON DIP 8 ON
Connect the last controller on the network to the RS-485 input terminal. Refer to LT-980 section 3.3.5 for end of line resistors to be used on the first and last nodes of network. The RS-485 terminal consists of + (positive), - (negative), and S (Shield) connections. Aperio Hub 3
A B
A B
A B
S101 DIP 6 ON DIP 7 ON DIP 8 ON
S101 DIP 6 OFF DIP 7 OFF DIP 8 OFF
S101 DIP 6 OFF DIP 7 OFF DIP 8 ON
JW1 OPEN JW2 OPEN
JW6. JW6 is not used and by default is open. Version 0.11 LT-1164
Aperio Hub 2
Aperio Door Controller Installation Quick Reference
OFF
The RS-485 connection consists of an input and output terminal. Connect the RS-485 output terminal to the RS-485 input terminal of the next controller.
16 Guage Wire
MD-1113 Module
8
RS-485
Aperio hubs on both ends of RS-485 bus. Aperio Hub 1
ON
software.
Connecting the Aperio Hubs to the MD-1113 RS-485 Network Terminal MD-1113 on one end and an Aperio hub on the other end of the RS-485 network bus.
Address 4
• Set DIP switch 8 ON to get IP address from TX3 Configurator
P3. Connector for MD-1113 Module Board. P4. Connector for MD-921 IP Module board.
Address 3
• Set DIP switch 8 OFF to get IP address from DHCP server.
Ground Terminal
optional
Address 2
S101 DIP 6 OFF DIP 7 OFF 1 8 1 8 1 8 1 DIP 8 ON • Keep DIP switch 7 at the factory set value
Power terminals for 16 Vac transformer (PS-4 or PS-4P)
+
USB. Computer connection for firmware download and configuration.
output of 1 A. For example, if output 7 provides 700 mA, then output 8 provides 300 mA.
S +
-
Connections
• a maximum output of 700 mA each, for a combined total
S101 DIP 6 OFF DIP 7 OFF DIP 8 OFF
OUTPUT
Black
J100
• 12 Vdc
P7 Aperio Hub 2
P1
RS-485
Thermal Kit
8-24VDC
• 30 Vac rated \ 1 amp
NO
MD-1113
RS-485 terminals for connecting to multiple TX3 controllers
S101
OUTPUT 5
C
ALARM
JW 1
S101 DIP 6 ON DIP 7 ON DIP 8 ON
EXT
• 30 Vdc \ 3 amp
NO NC
TROUBLE
Connection to 12V battery backup Module MD-1113
A B
ANTENNA
OUTPUT 4
C
LEDs
JW 5
A
NO NC
RS-485 terminals for Aperio Hubs (see figures below)
terminal on the MD-1113. 8-24VDC terminals on J100.
OUTPUT 3
C
P4
• Connect the B terminal on J100 to the negative (-) • Connect power (8-24 Vdc, 250 mA) to the GND and
NO NC
AC
JW2
• Connect the A terminal on J100 to the positive (+)
C
Outputs 7 and 8 IP Module Interface
hubs on the RS-485 network.
NO NC
C
O u ttpu p u t s 1 to 6
JW3
• Set DIP switch 7 on S101 to ON for one of the Aperio
GND
OUTPUT 8
C
Inputs 1 to 8
• Set DIP switch 6 on S101 to ON for one of the Aperio
D1
NC
12V
12V
B
Outputs 1 to 6 are relay contact programmable normally open (NO) or normally closed (NC) outputs. Any power supply connected to these outputs cannot exceed:
Ground Terminal The Card Access system is equipped with a 16 gauge electrical wire attached to the panel chassis Ground Terminal. Do not disconnect this wire. Attach the end of the supplied wire to a suitable grounding wire 16 gauge or thicker. Attach the other end to the cold water ground.
for more information see LT-1160 Aperio Door Controller System Manual available on CD, USB flash drive, or website WWW.MIRCOM.COM
TX3 Aperio Door Controller Installation Quick Reference
The following figure shows the various controller connections
Aperio Hub 1
Aperio Hub n
TX3 Aperio™ Door Controller Installation Quick Reference IMPORTANT This document is for reference only and does not replace the existing documentation. For more detailed information refer to the documentation on the CD, the USB flash drive, or Mircom website (www.mircom.com).
RS-485 Network for Aperio Hubs Maximum network bus length: 3,000 feet Use 22 AWG wire
Installation Prerequisites OUTPUTS 1 to 6
INPUTS 1 to 8
Relay contact, 2 amps
General purpose inputs General purpose input
General purpose input
1 pair 22 AWG
General purpose input
1 pair 22 AWG
1 pair 22 AWG
• Ensure there is a provision for a ground circuit. The Aperio Door Controller assembly must be grounded by a qualified
electrician. An improperly grounded unit can result in equipment malfunction and void the warranty. • Use the latest Aperio Door Controller System controller firmware. Mircom periodically updates panel firmware and
Configurator Software to add features and correct any minor inconsistencies. For information about the latest firmware or software visit the ‘Manuals and Downloads’ section of the Mircom website at www.mircom.com.
Aperio Door Controller
Basic Wiring
3 wires 22 AWG
1. Turn the controller power switch to OFF. 2. Connect the Aperio hub network bus to the RS-485 terminal on the MD-1113 Module board. 3. Connect any inputs and outputs. 1 pair 22 AWG
1 pair 18 AWG 1 pair 22 AWG
General purpose input
General purpose input
OUTPUTS 7 to 8
22 AWG
Programmable outputs Combined 1 amp output 12 Vdc 500 mA
Power transformer 16VAC/40VA PS-4 or PS-4P
Power transformer AC or DC Door strike supply
Configure the system using the Configurator software using a USB or modem connection. Verify the following: • Ensure that the controller and all connected devices and components are fully operational.
• Ensure the Configurator software is set with the correct controller RS-485 network address. 120 VAC 60HZ
Wiring requirements • Install all transformers outside the Lobby Control Unit enclosure. • Unless specified otherwise, all wiring is a maximum length of 1000 ft. The RS-485 wiring maximum length is 4000 ft. • All units use the PS-4P transformer for the power supply. The door strike power supply depends on the door strike
Version 0.11 LT-1164
Before Starting the Configuration
• Ensure the controller DIP Switches are set with a unique RS-485 network address.
Single Panel Wiring
power requirements.
5. Set SW2 to a unique RS-485 network address. 6. Turn the controller power switch to ON (a correctly wired controller will show a green AC LED).
RS-485 Network for TX3 devices
Electrical room
4. Connect the controller supply.
• Ensure that your PC is set with the correct date and time.
To Start the Configuration 1. Connect the PC to the controller using the USB port or modem connection. 2. Launch the Configurator and select the correct controller you are connecting to (on the basis of name, panel label, panel model, and network address). 3. Click Connect. The connection icon appears in the Configurator tool bar. 4. Ensure that the panel is configured with the correct date and time. 5. Configure the Aperio Door Controller using the instructions in the LT-1160 Installation and Operation Manual. for more information go to the CD, USB flash drive, or website and read the LT-1160 Aperio Door Controller System Manual WWW.MIRCOM.COM
