0h9LMkrQsq2mO4nmleqR B 001 00407D 14 revD
NOTES: 1. UNLESS OTHERWISE SPECIFIED ALL UNITS ARE INCHES 2. DO NOT SCALE DRAWING 3. ASSEMBLY AND/OR COMPONENTS ARE SHOWN IN INSPECTION ORIENTATION 4. STIFFENERS OR ADDITIONAL STRUCTURE MAY NOT BE ADDED (LHS/RHS) 5. ROCKER PANEL EXTENSIONS MUST EXTEND FROM WHEEL OPENING TO WHEEL OPENING 6. ROCKER PANEL EXTENSIONS MAY BE TRIMMED FOR EXHAUST CLEARANCE AND JACK CLEARANCE 7. AT SUPERSPEEDWAYS, THE RHS VERTICAL EXTENSION MUST NOT BE ABOVE THE BOTTOM SURFACE OF THE EXHAUST PIPES 8. LHS VERTICAL EXTENSION MUST NOT BE HIGHER THAN THE RHS VERTICAL EXTENSION
REV
DESCRIPTION
DRAWN BY
DATE
A
FINAL
SHOUP
08/21/2014
POPIELA
12/12/2014
CHAPPELL
12/08/2015
CHAPPELL
06/29/2016
B C D
ADDED 1.0 MAX. DIMENSION FROM EDGE OF ROCKER PANEL EXTENSION TO FIRST BOLT CENTER ON BOTH LHS/RHS VIEWS UPDATED DRAWING BORDER, TITLE BLOCK AND TOLERANCES TO 2016 STANDARDS ADDED RHS REAR PANEL SINGLE COMPONENT NOTE
A
D EFFECTIVE JULY 20, 2016, RHS REAR PANEL MUST BE SINGLE COMPONENT. NO TWO-PIECE RHS REAR PANELS ALLOWED
MUST BE FLUSH WITH SIDE OF BODY
1/4 MAX. BUTTON HEAD BOLT
MUST USE SINGLE SAE TYPE WASHER
MAX. (6) BUTTON HEAD BOLTS MAY BE USED FOR ATTACHEMENT OF METAL PORTION
A
0
SECTION A-A ROCKER PANEL EXTENSIONS - ROCKER PANEL EXTENSIONS SCALE 10:1
RHS REAR PANEL MAY BE METAL
INSPECTION SURFACE A
1.0 MAX. 30.0 MAX.
3.0 MIN. 5.0 MAX.
LOWER EDGE OF ROCKER PANEL EXTENSION MUST BE LINEAR (LHS/RHS)
A
0
INSPECTION SURFACE 3.0 MIN. 5.0 MAX.
1.0 MAX.
TOLERANCES (INCHES) ANGULAR 1 DEG X.X .1 X.XX .01 X.XXX .005 X.XXXX .0010 LEGAL NOTICE: TRADE SECRETS AND/OR CONFIDENTIAL/PROPRIETARY INFORMATION OWNED BY NASCAR, INC. IS CONTAINED HEREIN AND MAY NOT BE DISCLOSED, USED, DUPLICATED, OR DISTRIBUTED WITHOUT NASCARS PRIOR WRITTEN CONSENT. FAILURE TO PROTECT NASCAR'S TRADE SECRETS AND/OR CONFIDENTIAL/PROPRIETARY INFORMATION MAY RESULT IN LIABILITY FOR ALL RESULTING DAMAGES AND LOSSES.
TITLE
RULE BOOK ROCKER PANEL EXTENSIONS - ROCKER PANEL EXTENSIONS
* UNLESS OTHERWISE SPECIFIED DRAWN BY DATE
SHOUP 04/09/2014
SIZE
D
SCALE
DRAWING NUMBER
.125
REV
B-001-00407D-14
SHEET
1 OF 1
MATERIAL
D
PLASTIC
REV
DESCRIPTION
DRAWN BY
DATE
A
FINAL
SHOUP
08/21/2014
POPIELA
12/12/2014
CHAPPELL
12/08/2015
CHAPPELL
06/29/2016
B C D
ADDED 1.0 MAX. DIMENSION FROM EDGE OF ROCKER PANEL EXTENSION TO FIRST BOLT CENTER ON BOTH LHS/RHS VIEWS UPDATED DRAWING BORDER, TITLE BLOCK AND TOLERANCES TO 2016 STANDARDS ADDED RHS REAR PANEL SINGLE COMPONENT NOTE
A
D EFFECTIVE JULY 20, 2016, RHS REAR PANEL MUST BE SINGLE COMPONENT. NO TWO-PIECE RHS REAR PANELS ALLOWED
MUST BE FLUSH WITH SIDE OF BODY
1/4 MAX. BUTTON HEAD BOLT
MUST USE SINGLE SAE TYPE WASHER
MAX. (6) BUTTON HEAD BOLTS MAY BE USED FOR ATTACHEMENT OF METAL PORTION
A
0
SECTION A-A ROCKER PANEL EXTENSIONS - ROCKER PANEL EXTENSIONS SCALE 10:1
RHS REAR PANEL MAY BE METAL
INSPECTION SURFACE A
1.0 MAX. 30.0 MAX.
3.0 MIN. 5.0 MAX.
LOWER EDGE OF ROCKER PANEL EXTENSION MUST BE LINEAR (LHS/RHS)
A
0
INSPECTION SURFACE 3.0 MIN. 5.0 MAX.
1.0 MAX.
TOLERANCES (INCHES) ANGULAR 1 DEG X.X .1 X.XX .01 X.XXX .005 X.XXXX .0010 LEGAL NOTICE: TRADE SECRETS AND/OR CONFIDENTIAL/PROPRIETARY INFORMATION OWNED BY NASCAR, INC. IS CONTAINED HEREIN AND MAY NOT BE DISCLOSED, USED, DUPLICATED, OR DISTRIBUTED WITHOUT NASCARS PRIOR WRITTEN CONSENT. FAILURE TO PROTECT NASCAR'S TRADE SECRETS AND/OR CONFIDENTIAL/PROPRIETARY INFORMATION MAY RESULT IN LIABILITY FOR ALL RESULTING DAMAGES AND LOSSES.
TITLE
RULE BOOK ROCKER PANEL EXTENSIONS - ROCKER PANEL EXTENSIONS
* UNLESS OTHERWISE SPECIFIED DRAWN BY DATE
SHOUP 04/09/2014
SIZE
D
SCALE
DRAWING NUMBER
.125
REV
B-001-00407D-14
SHEET
1 OF 1
MATERIAL
D
PLASTIC
