20 gauge, non-corrosive stainless steel construction ... - TriMark USA
ITEM NO.
l
l
l
l
l
l
l
l
l
10-10evh shown
_______________________
Operate an Alto-Shaam® Combitherm® CombiOven without an expensive oven hood or costly hood installation.
Keep costly heating and air conditioning from being vented out through your hood.
Self-contained oven venting system fully tested and listed by Underwriters Laboratories for both safety and sanitation. Using EPA method 202 testing, grease laden vapors emitted by the Combi Ventless hood are 0.58 mg/m 3 – far less than U.L.'s established standard of 5 mg/m 3 . Alto-Shaam's factory installed Ventless Hood is placed directly on the top of a Combitherm oven. A high-power fan captures all steam and fumes from the oven cavity into the hood intake and out the back surface exhaust vent, trapping grease as the air moves through the filter system. As fumes and vapors are circulated through the hood, condensed steam drains from an opening at the rear. CombihoodPLUS™ performance is "smart"; engaging the fan during the last minute of the cook mode which provides quiet operation and consumes less power. Power requirements to the ventless hood operate directly from the power supplied to the Combi oven.
20 gauge, non-corrosive stainless steel construction ventless hood is factory installed directly on the top of the electric Alto-Shaam ® Combitherm ® oven. The hood is designed to vent clean air back into the kitchen, filtering vapors and grease. A high-power fan draws fumes and steam into the hood intake and out the back exhaust vent. Fumes and vapors are circulated through filters draining the condensation through a drain at the rear of the hood. An activated charcoal filter cleans the air before venting it out the top of the hood. One (1) grease and one (1) charcoal filter is included, and access from the front of the oven simplifies replacement. not available for combi models equipped the smoking option , stacked configurations , or gas models .
COMBIHOOD FILTERS Charcoal, Class I ( required for new york city and los angeles ) FI-36620 Charcoal, Class II FI-25866 Grease FI-25867
ANSI/NSF 4
EPA 202 CAPTURE TEST
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 • U.S.A. PHONE :
262.251.3800 800.558.8744 U . S . A ./ CANADA
FAX :
262.251.7067 800.329.8744 U . S . A .
ONLY
www.alto-shaam.com PRINTED IN U.S.A.
DUE TO ONGOING PRODUCT IMPROVEMENT, SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
#457 - 01/14
112°
112°
33-3/4" (856mm)
2" (50mm)
6-3/4" (171mm)
112°
112°
42-1/4" (1072mm) 42-1/4" (1072mm) 43-3/16" (1096mm) 43-3/16" (1096mm) 31-3/4" (807mm) 31-3/4" (807mm)
43-3/16" (1096mm)
49-3/8" (1253mm)
49-3/8" (1253mm)
112°
112°
6-3/4" (171mm) 6-3/4" (171mm)
42-1/4" (1072mm) 42-1/4"(1096mm) (1072mm) 43-3/16"
43-3/16" (1096mm) 31-3/4" (807mm) 31-3/4" (807mm)
6-3/4" (171mm) 6-3/4" (171mm)
35-7/8" (910mm) 35-7/8" (910mm)
21-15/16" (557mm) 16-7/16" (417mm)
49-3/8" (1253mm)
112°
21-15/16" (557mm) 16-7/16" (417mm)
21-15/16" (557mm) 16-7/16" (417mm) 49-3/8" (1253mm)
21-15/16" (557mm) 16-7/16" (417mm)
35-7/8" (910mm) 35-7/8" (910mm)
35-7/8" (910mm)
CTP6-10EVH CTC6-10EVH
6-3/4" (171mm)
21-15/16" (557mm) 16-7/16" (417mm)
31-3/4" (807mm)
112° 112°
112° 1-11/16" (42mm) 1-11/16" (42mm)
42-1/4" 42-1/4" (1072mm) (1072mm)
43-3/16" 43-3/16" (1096mm) (1096mm) 6-3/4" (171mm) 6-3/4" (171mm)
31-3/4" (807mm) 31-3/4" (807mm)
21-15/16" (557mm) 16-7/16" (417mm) 21-15/16" (557mm) 16-7/16" (417mm)
35-7/8" 35-7/8" (910mm) (910mm) 1-11/16" (42mm) 1-11/16" (42mm)
112°112°
60-5/8" (1539mm)
60-5/8" (1539mm)
CTP10-10EVH CTC10-10EVH
inst al lat i o n req u irem en t s Water drain outlet is 3/4" NPT
1-11/16" 1-11/16" (42mm) (42mm)
Sp e ci fi cat i o n s
6-10EV H
10-10EV H
HOO D D IMENSIONS H x W x D
16-7/16" x 35-7/8" x 38-1/2" (417mm x 910mm x 978mm)
16-7/16" x 35-7/8" x 38-1/2" (417mm x 910mm x 978mm)
HOOD W ITH O V EN DIMENSIONS HxWxD
49-3/8" x 35-7/8" x 42-1/4" (1253mm x 910mm x 1072mm)
60-5/8" x 35-7/8" x 42-1/4" (1539mm x 910mm x 1072mm)
756 CFM
756 CFM
1.1A
1.1A
.25
.25
Sh i p W e i g h t
contact factory
contact factory
cra t e D i m e n s i o n s L x W x H
contact factory
contact factory
Air Movement add i t i o n a l E l ec t ri c al r e q u i r e me n t s A mp s kW
#457 - 01/14
due to ongoing product improvement, specifications are subject to change without notice.
www.alto-shaam.com
9/16" (294mm)
-1/2" (88mm)
3-1/4" (81mm)
46-5/8" (1184mm)
8-1/16" (206mm)
43-3/8" (1102mm)
2" (50mm) 33-3/4" (856mm)
1-13/16" (45mm)
60°
46-15/16" 46-15/16"(1191mm) (1191mm) 43-3/16" 43-3/16"(1096mm) (1096mm)
11-9/16"(294mm) (294mm) 11-9/16"
31-3/4"(807mm) (807mm) 31-3/4"
3-1/2"(88mm) (88mm) 3-1/2"
21-15/16" (557mm) 3-1/2" (88mm)
47" (1192mm) 47" (1192mm)
1-13/16" (45mm)
43-3/16"43-3/16" (1096mm) (1096mm) BASE: BOTTOM OF HOOD 11-9/16" 11-9/16" 31-3/4" (807mm) 31-3/4" (807mm) (294mm)(294mm) RESTS ON TOP OF UNIT
112°
3-1/4" (81 3
60° BASE: BOTTOM BASE: BOTTOM OF HOOD OF HOOD RESTS ON RESTS TOPON OF TOP UNITOF UNIT
1-11/16"1-11/16" (42mm) (42mm)
Water drain outlet is 3/4" NPT
HOO D D IMENSIONS H x W x D HOO D W ITH O V EN DIMENSIONS HxWxD Air Movement
7-20EV H
10-20EV H
16-7/16" x 43-15/16" x 43-3/8" (417mm x 1115mm x 1102mm)
16-7/16" x 43-15/16" x 43-3/8" (417mm x 1115mm x 1102mm)
52-3/4" x 43-15/16" x 46-5/8" (1339mm x 1115mm x 1184mm)
60-3/8" x 43-15/16" x 47" (1535mm x 1115mm x 1192mm)
756 CFM
756 CFM
1.1A
1.1A
add i t i o n a l E l ec t ri c al requirements A m p s
.25
.25
Sh i p W e i g h t
contact factory
contact factory
cra t e D i m e n s i o n s L x W x H
contact factory
contact factory
kW
#457 - 01/14
15" (380mm)
16-7/16" (417mm) 1-13/16"TOP (45mm) COVER TO VENT HOOD 1-13/16" (45mm)
16-7/16" (417mm)
21-15/16" (557mm) 16-7/16" (417mm)
21-15/16" (557mm) 15" (380mm)
11-9/16" (294mm)
inst al lat i o n req u irem en t s
Sp e ci fi cat i o n s
11
60°
112°
16-7/16" (417mm)
31-3/4" (807mm)
60° 60°
112°
15" (380mm)
16-7/16" (417mm)
TOP COVER TO VENT HOOD
16-7/16" (417mm)
21-15/16" (557mm) TOP COVER TO VENT HOOD
16-7/16" (417mm)
16-7/16" (417mm)
TOP COVER TO VENT HOOD
52-3/4" (1339mm) 60-3/8" (1535mm)
60-3/8" (1535mm)
43-15/16" 43-15/16" (1115mm) (1115mm)
43-3/16" (1096mm)
52-3/4" (1339mm)
52-3/4" 52-3/4" (1339mm) (1339mm)
BASE:BOTTOM BOTTOMOF OFHOOD HOOD BASE: RESTSON ONTOP TOP OFUNIT UNIT RESTS OF 46-15/16" (1191mm)
43-15/16" (1115mm)
CTP10-20EVH CTC10-20EVH
43-15/16" (1115mm)
112° 112°
16-7/16" 16-7/16" (417mm) (417mm) 15" (380mm) (380mm) 15"
16-7/16" 16-7/16" (417mm) (417mm)
CTP7-20EVH CTC7-20EVH
15" (380mm)
TOP TOP COVER COVER TO TO VENT VENT HOOD HOOD
21-15/16" 21-15/16" (557mm) (557mm)
43-15/16" 43-15/16"(1115mm) (1115mm)
due to ongoing product improvement, specifications are subject to change without notice.
www.alto-shaam.com
60°
l
l
l
l
l
l
l
l
l
10-10evh shown
_______________________
Operate an Alto-Shaam® Combitherm® CombiOven without an expensive oven hood or costly hood installation.
Keep costly heating and air conditioning from being vented out through your hood.
Self-contained oven venting system fully tested and listed by Underwriters Laboratories for both safety and sanitation. Using EPA method 202 testing, grease laden vapors emitted by the Combi Ventless hood are 0.58 mg/m 3 – far less than U.L.'s established standard of 5 mg/m 3 . Alto-Shaam's factory installed Ventless Hood is placed directly on the top of a Combitherm oven. A high-power fan captures all steam and fumes from the oven cavity into the hood intake and out the back surface exhaust vent, trapping grease as the air moves through the filter system. As fumes and vapors are circulated through the hood, condensed steam drains from an opening at the rear. CombihoodPLUS™ performance is "smart"; engaging the fan during the last minute of the cook mode which provides quiet operation and consumes less power. Power requirements to the ventless hood operate directly from the power supplied to the Combi oven.
20 gauge, non-corrosive stainless steel construction ventless hood is factory installed directly on the top of the electric Alto-Shaam ® Combitherm ® oven. The hood is designed to vent clean air back into the kitchen, filtering vapors and grease. A high-power fan draws fumes and steam into the hood intake and out the back exhaust vent. Fumes and vapors are circulated through filters draining the condensation through a drain at the rear of the hood. An activated charcoal filter cleans the air before venting it out the top of the hood. One (1) grease and one (1) charcoal filter is included, and access from the front of the oven simplifies replacement. not available for combi models equipped the smoking option , stacked configurations , or gas models .
COMBIHOOD FILTERS Charcoal, Class I ( required for new york city and los angeles ) FI-36620 Charcoal, Class II FI-25866 Grease FI-25867
ANSI/NSF 4
EPA 202 CAPTURE TEST
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 • U.S.A. PHONE :
262.251.3800 800.558.8744 U . S . A ./ CANADA
FAX :
262.251.7067 800.329.8744 U . S . A .
ONLY
www.alto-shaam.com PRINTED IN U.S.A.
DUE TO ONGOING PRODUCT IMPROVEMENT, SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
#457 - 01/14
112°
112°
33-3/4" (856mm)
2" (50mm)
6-3/4" (171mm)
112°
112°
42-1/4" (1072mm) 42-1/4" (1072mm) 43-3/16" (1096mm) 43-3/16" (1096mm) 31-3/4" (807mm) 31-3/4" (807mm)
43-3/16" (1096mm)
49-3/8" (1253mm)
49-3/8" (1253mm)
112°
112°
6-3/4" (171mm) 6-3/4" (171mm)
42-1/4" (1072mm) 42-1/4"(1096mm) (1072mm) 43-3/16"
43-3/16" (1096mm) 31-3/4" (807mm) 31-3/4" (807mm)
6-3/4" (171mm) 6-3/4" (171mm)
35-7/8" (910mm) 35-7/8" (910mm)
21-15/16" (557mm) 16-7/16" (417mm)
49-3/8" (1253mm)
112°
21-15/16" (557mm) 16-7/16" (417mm)
21-15/16" (557mm) 16-7/16" (417mm) 49-3/8" (1253mm)
21-15/16" (557mm) 16-7/16" (417mm)
35-7/8" (910mm) 35-7/8" (910mm)
35-7/8" (910mm)
CTP6-10EVH CTC6-10EVH
6-3/4" (171mm)
21-15/16" (557mm) 16-7/16" (417mm)
31-3/4" (807mm)
112° 112°
112° 1-11/16" (42mm) 1-11/16" (42mm)
42-1/4" 42-1/4" (1072mm) (1072mm)
43-3/16" 43-3/16" (1096mm) (1096mm) 6-3/4" (171mm) 6-3/4" (171mm)
31-3/4" (807mm) 31-3/4" (807mm)
21-15/16" (557mm) 16-7/16" (417mm) 21-15/16" (557mm) 16-7/16" (417mm)
35-7/8" 35-7/8" (910mm) (910mm) 1-11/16" (42mm) 1-11/16" (42mm)
112°112°
60-5/8" (1539mm)
60-5/8" (1539mm)
CTP10-10EVH CTC10-10EVH
inst al lat i o n req u irem en t s Water drain outlet is 3/4" NPT
1-11/16" 1-11/16" (42mm) (42mm)
Sp e ci fi cat i o n s
6-10EV H
10-10EV H
HOO D D IMENSIONS H x W x D
16-7/16" x 35-7/8" x 38-1/2" (417mm x 910mm x 978mm)
16-7/16" x 35-7/8" x 38-1/2" (417mm x 910mm x 978mm)
HOOD W ITH O V EN DIMENSIONS HxWxD
49-3/8" x 35-7/8" x 42-1/4" (1253mm x 910mm x 1072mm)
60-5/8" x 35-7/8" x 42-1/4" (1539mm x 910mm x 1072mm)
756 CFM
756 CFM
1.1A
1.1A
.25
.25
Sh i p W e i g h t
contact factory
contact factory
cra t e D i m e n s i o n s L x W x H
contact factory
contact factory
Air Movement add i t i o n a l E l ec t ri c al r e q u i r e me n t s A mp s kW
#457 - 01/14
due to ongoing product improvement, specifications are subject to change without notice.
www.alto-shaam.com
9/16" (294mm)
-1/2" (88mm)
3-1/4" (81mm)
46-5/8" (1184mm)
8-1/16" (206mm)
43-3/8" (1102mm)
2" (50mm) 33-3/4" (856mm)
1-13/16" (45mm)
60°
46-15/16" 46-15/16"(1191mm) (1191mm) 43-3/16" 43-3/16"(1096mm) (1096mm)
11-9/16"(294mm) (294mm) 11-9/16"
31-3/4"(807mm) (807mm) 31-3/4"
3-1/2"(88mm) (88mm) 3-1/2"
21-15/16" (557mm) 3-1/2" (88mm)
47" (1192mm) 47" (1192mm)
1-13/16" (45mm)
43-3/16"43-3/16" (1096mm) (1096mm) BASE: BOTTOM OF HOOD 11-9/16" 11-9/16" 31-3/4" (807mm) 31-3/4" (807mm) (294mm)(294mm) RESTS ON TOP OF UNIT
112°
3-1/4" (81 3
60° BASE: BOTTOM BASE: BOTTOM OF HOOD OF HOOD RESTS ON RESTS TOPON OF TOP UNITOF UNIT
1-11/16"1-11/16" (42mm) (42mm)
Water drain outlet is 3/4" NPT
HOO D D IMENSIONS H x W x D HOO D W ITH O V EN DIMENSIONS HxWxD Air Movement
7-20EV H
10-20EV H
16-7/16" x 43-15/16" x 43-3/8" (417mm x 1115mm x 1102mm)
16-7/16" x 43-15/16" x 43-3/8" (417mm x 1115mm x 1102mm)
52-3/4" x 43-15/16" x 46-5/8" (1339mm x 1115mm x 1184mm)
60-3/8" x 43-15/16" x 47" (1535mm x 1115mm x 1192mm)
756 CFM
756 CFM
1.1A
1.1A
add i t i o n a l E l ec t ri c al requirements A m p s
.25
.25
Sh i p W e i g h t
contact factory
contact factory
cra t e D i m e n s i o n s L x W x H
contact factory
contact factory
kW
#457 - 01/14
15" (380mm)
16-7/16" (417mm) 1-13/16"TOP (45mm) COVER TO VENT HOOD 1-13/16" (45mm)
16-7/16" (417mm)
21-15/16" (557mm) 16-7/16" (417mm)
21-15/16" (557mm) 15" (380mm)
11-9/16" (294mm)
inst al lat i o n req u irem en t s
Sp e ci fi cat i o n s
11
60°
112°
16-7/16" (417mm)
31-3/4" (807mm)
60° 60°
112°
15" (380mm)
16-7/16" (417mm)
TOP COVER TO VENT HOOD
16-7/16" (417mm)
21-15/16" (557mm) TOP COVER TO VENT HOOD
16-7/16" (417mm)
16-7/16" (417mm)
TOP COVER TO VENT HOOD
52-3/4" (1339mm) 60-3/8" (1535mm)
60-3/8" (1535mm)
43-15/16" 43-15/16" (1115mm) (1115mm)
43-3/16" (1096mm)
52-3/4" (1339mm)
52-3/4" 52-3/4" (1339mm) (1339mm)
BASE:BOTTOM BOTTOMOF OFHOOD HOOD BASE: RESTSON ONTOP TOP OFUNIT UNIT RESTS OF 46-15/16" (1191mm)
43-15/16" (1115mm)
CTP10-20EVH CTC10-20EVH
43-15/16" (1115mm)
112° 112°
16-7/16" 16-7/16" (417mm) (417mm) 15" (380mm) (380mm) 15"
16-7/16" 16-7/16" (417mm) (417mm)
CTP7-20EVH CTC7-20EVH
15" (380mm)
TOP TOP COVER COVER TO TO VENT VENT HOOD HOOD
21-15/16" 21-15/16" (557mm) (557mm)
43-15/16" 43-15/16"(1115mm) (1115mm)
due to ongoing product improvement, specifications are subject to change without notice.
www.alto-shaam.com
60°
