24V RGB LED RiBBon
24V RGB LED Ribbon 17.0 BL-RBN-ILL-24V-RGB [ 21"] 32
50.0 31"] [132
6.0 1"] [4
Diagrams - Dimensions 14.0 9 "] [16
application12.0
• Indoors or Outdoors[15 - Wet or dry locations 32"] • Accent Lighting • Cove IP68 Lighting LED • Decorative Ribbon Highlights • Architectural, Building, Linear Outlining 100.0
Lighting
6.0 1"] [4
LED
[315 16"]
IP65
SMD5060 RGB LED 60 LED/m (18 LED/ft)
Beam Angle
120°
Colour
RGB
Avg Life
50,000 hr
Lumen Output
272 lm/m (83 lm/ft)
Efficacy
LOW
22 lm/W
14.0 RGB controllers 9 "] [16 3 Channel PWM & control system
Control
Electrical HL LED
6.0 1"] [4
100.0 [315"] 16
Ribbon Input Voltage*
24V DC
Connections
Order termination kits or solder 31 leads in field
Power Draw
6.0 1"] [4
Operating Temp Circuit
50.0
12.5 W/m (3.8 W/ft)
[132"]
-20°C to 40°C High ambient temperature will shorten LED life In parallel *Do not plug directly into 120V
Sample application
Mechanical14.0
Housing Construction[ 9 "] Flexible PCB board 16 Silicone jacket Min Cut CTLength LED
10 cm (3-15/16”) 6 LEDs per cut
Ribbon Max Run Length
128.0 1 IP65 Splash proof [532"]
5 m (16’4”)
Weatherability
6.0 1"] [4
Bend Radius
Medial bend of 38 mm (1.5”)
accessories Mounting
CONTROLLER BL-CONT-IR-T80
RGB Controller with IR remote
BL-CONT-RF-T80
RGB Controller with RF remote
BL-DMX-LCI
DMX Controller with preset colours and programs RF Remote
BL-DMX-SRC144
DMX Controller with 54 DMX channels
BL-DMX-SRC174
DMX Controller with 194 DMX channels
BL-DMX-USB
DMX USB Controller with 132 DMX channels PC compatible, IR Remote
BL-DMX-Touchpad
Touch sensitive DMX controller PC compatible 128 DMX channels
BL-DMX-Touchpad-ETH
Touch sensitive DMX controller PC compatible 2 DMX universes Ethernet connection & Clock triggering
BL-RBN-CLP
Silicone mounting clip
BL-RBN-DSIDE-TAPE
Double sided tape - 1 roll of 50 m (164 ft)
BL-LOCTITE
Concrete surface clear adhesive (300 ml)
BL-DOW832
Silicone rubber adhesive sealant (300 ml)
Termination BL-RBN-TK-RGB
Termination kit (required per Ribbon run) - 3ft 20 AWG lead wire installed - End caps
BL-RBN-JC
Ribbon Light jumper cable termination
BL-RBN-CAP
Cap for Ribbon Light
BL-RBN-LEAD-xx
Extra lead for termination on top of 3ft lead wire -xx denotes wire gauge AWG (20, 18, 16, 16 Plenum)
MAX LENGTH PER DRIVER Power
Max Length 25 W
1.8 m (6 ft)
60 W
4.6 m (15 ft)
100 W
7.3 m (24 ft) Other driver wattage available 10% buffer recommended
Solid State Lighting is sensitive to power fluctuations Surge protection is highly recommended for all LED lighting products and should be on a designated circuit to protect against premature failure Lack of surge protection may void your warranty
111 - 8838 Heather St. Vancouver BC Canada V6P 3S8 Ph: 1-604-874-4405 • Fx: 1-604-321-0445 • www.bllighting.com • [email protected]
BL-RBN-ILL-24V-RGB - Page 1 December 26, 2013 12:03 PM Specifications subject to change without notice
Ordering BL-RBN-ILL-24V-RGB
Termination BL-RBN-RGB-TK BL-RBN-LEAD-xx BL-RBN-CAP BL-RBN-JC
i
Mounting BL-RBN-CLP BL-DOW832 Blue (-) BL-LOCTITE Green (-) BL-RBN-DSIDE-TAPE
DC Transformer BL-MAG-DC-24V-xx
Enclosure BL-ENC-HNG-xx BL-ENC-SCW-xx BL-ENC-PVC-xx Surge Protector
Connection diagram
Green (gnd)
Red (+)
V+ (+) Down Back
Enter Up
LED Driver BL-LT-CV-24V-xx LED Ribbon BL-HPT-CV-24V-xx BL-GH-CV-24V-xx
Red (-)
VCC (+)
12/24V DC LED Driver
V- (-)
Black (-)
Blue (-)
White (-)
Brown (+)
Black (+)
Controller BL-CONT-IR-T80 BL-CONT-RF-T88 BL-CONT-DMX-LCI BL-DMX-USB BL-DMX-SRC144 BL-DMX-SRC-174 Power Supply BL-DMX-Touchpad
Controller Accessory BL-PWM-12/24V-3CH BL-AMP-T85 BL-DMX-SRC143 BL-DMX-CABLE-1.8M BL-DMX-CABLE-5M BL-DMX-CABLE-10M BL-DMX-CABLE-18AWG
Surge Protector BL-SP-277-20KA
RGB LED Ribbon with LCI Controller to DMX Master controller LED Ribbon
Blue (-)
Surge Protector
Green (-)
i
Red (-) VCC (+) Down Back
Green (gnd)
Red (+)
V+ (+) Enter Up
12/24V DC LED Driver
V- (-)
Black (-)
Blue (-)
White (-)
Brown (+)
Black (+)
Power Supply
RGB LED Ribbon with LCI Controller to DMX Master controller
DMX Controller
DMX Cable
LED Ribbon
Blue (-)
Surge Protector
Green (-)
i
Red (-) VCC (+)
Green (gnd)
Red (+)
V+ (+) Down Back
Enter Up
12/24V DC LED Driver
V- (-)
Black (-)
Blue (-)
White (-)
Brown (+)
Black (+)
Surge Protector
Green (-)
i
Red (-) VCC (+)
Enter Up
Green (gnd)
Red (+)
V+ (+) Down Back
12/24V DC LED Driver
V- (-)
Black (-)
Blue (-)
White (-)
Brown (+)
Black (+)
Surge
Green (-)
SurgeProtector Protector
RGB LED Ribbon with T80 Controller and Amplifier i Red (-) VCC (+)
R G B
LIGHT
V+
+
-
POWER
Enter
V+ (+) Down Back
V- (-) V+ (+)
DC 12/24V
V+ (+) Red (-) Green (-) Blue (-)
V- (-)
Power Supply
LED Ribbon
Blue (-)
RGB Controller Up
Power Supply
LED Ribbon
Blue (-)
DMX + DMX DMX gnd
Green (gnd)
Red (+)
Black (-)
12/24V DC LED Driver
12/24VBlack DC LED (-) Driver
Blue (-)
Blue (-)
Brown (+)
Brown (+)
Red (+)
Green (gnd)
White (-)
White (-)
Power Supply
Power Supply
Black (+)
Black (+)
LED Ribbon V+ (+) Red (-) Green (-) Blue (-) Surge Protector
Amplifier
Green (gnd)
-
POWER
Black (-)
R
LIGHT
V+
G
R
LIGHT
G
V+
+
B
B
DMX + DMX DMX gnd
Ordering
V- (-) V+ (+)
DC 12/24V
V+ (+) Red (-) Green (-) Blue (-)
12/24V DC LED Driver Red (+)
Blue (-)
White (-)
Brown (+)
Black (+)
LED Ribbon
Power Supply
Actual wire colours may vary - follow labels on the units Recommended to add 10% buffer when sizing power supply LED drivers require enclosures
Solid State Lighting is sensitive to power fluctuations Surge protection is highly recommended for all LED lighting products and should be on a designated circuit to protect against premature failure Lack of surge protection may void your warranty
111 - 8838 Heather St. Vancouver BC Canada V6P 3S8 Ph: 1-604-874-4405 • Fx: 1-604-321-0445 • www.bllighting.com • [email protected]
BL-RBN-ILL-24V-RGB - Page 2 December 26, 2013 12:03 PM Specifications subject to change without notice
50.0 31"] [132
6.0 1"] [4
Diagrams - Dimensions 14.0 9 "] [16
application12.0
• Indoors or Outdoors[15 - Wet or dry locations 32"] • Accent Lighting • Cove IP68 Lighting LED • Decorative Ribbon Highlights • Architectural, Building, Linear Outlining 100.0
Lighting
6.0 1"] [4
LED
[315 16"]
IP65
SMD5060 RGB LED 60 LED/m (18 LED/ft)
Beam Angle
120°
Colour
RGB
Avg Life
50,000 hr
Lumen Output
272 lm/m (83 lm/ft)
Efficacy
LOW
22 lm/W
14.0 RGB controllers 9 "] [16 3 Channel PWM & control system
Control
Electrical HL LED
6.0 1"] [4
100.0 [315"] 16
Ribbon Input Voltage*
24V DC
Connections
Order termination kits or solder 31 leads in field
Power Draw
6.0 1"] [4
Operating Temp Circuit
50.0
12.5 W/m (3.8 W/ft)
[132"]
-20°C to 40°C High ambient temperature will shorten LED life In parallel *Do not plug directly into 120V
Sample application
Mechanical14.0
Housing Construction[ 9 "] Flexible PCB board 16 Silicone jacket Min Cut CTLength LED
10 cm (3-15/16”) 6 LEDs per cut
Ribbon Max Run Length
128.0 1 IP65 Splash proof [532"]
5 m (16’4”)
Weatherability
6.0 1"] [4
Bend Radius
Medial bend of 38 mm (1.5”)
accessories Mounting
CONTROLLER BL-CONT-IR-T80
RGB Controller with IR remote
BL-CONT-RF-T80
RGB Controller with RF remote
BL-DMX-LCI
DMX Controller with preset colours and programs RF Remote
BL-DMX-SRC144
DMX Controller with 54 DMX channels
BL-DMX-SRC174
DMX Controller with 194 DMX channels
BL-DMX-USB
DMX USB Controller with 132 DMX channels PC compatible, IR Remote
BL-DMX-Touchpad
Touch sensitive DMX controller PC compatible 128 DMX channels
BL-DMX-Touchpad-ETH
Touch sensitive DMX controller PC compatible 2 DMX universes Ethernet connection & Clock triggering
BL-RBN-CLP
Silicone mounting clip
BL-RBN-DSIDE-TAPE
Double sided tape - 1 roll of 50 m (164 ft)
BL-LOCTITE
Concrete surface clear adhesive (300 ml)
BL-DOW832
Silicone rubber adhesive sealant (300 ml)
Termination BL-RBN-TK-RGB
Termination kit (required per Ribbon run) - 3ft 20 AWG lead wire installed - End caps
BL-RBN-JC
Ribbon Light jumper cable termination
BL-RBN-CAP
Cap for Ribbon Light
BL-RBN-LEAD-xx
Extra lead for termination on top of 3ft lead wire -xx denotes wire gauge AWG (20, 18, 16, 16 Plenum)
MAX LENGTH PER DRIVER Power
Max Length 25 W
1.8 m (6 ft)
60 W
4.6 m (15 ft)
100 W
7.3 m (24 ft) Other driver wattage available 10% buffer recommended
Solid State Lighting is sensitive to power fluctuations Surge protection is highly recommended for all LED lighting products and should be on a designated circuit to protect against premature failure Lack of surge protection may void your warranty
111 - 8838 Heather St. Vancouver BC Canada V6P 3S8 Ph: 1-604-874-4405 • Fx: 1-604-321-0445 • www.bllighting.com • [email protected]
BL-RBN-ILL-24V-RGB - Page 1 December 26, 2013 12:03 PM Specifications subject to change without notice
Ordering BL-RBN-ILL-24V-RGB
Termination BL-RBN-RGB-TK BL-RBN-LEAD-xx BL-RBN-CAP BL-RBN-JC
i
Mounting BL-RBN-CLP BL-DOW832 Blue (-) BL-LOCTITE Green (-) BL-RBN-DSIDE-TAPE
DC Transformer BL-MAG-DC-24V-xx
Enclosure BL-ENC-HNG-xx BL-ENC-SCW-xx BL-ENC-PVC-xx Surge Protector
Connection diagram
Green (gnd)
Red (+)
V+ (+) Down Back
Enter Up
LED Driver BL-LT-CV-24V-xx LED Ribbon BL-HPT-CV-24V-xx BL-GH-CV-24V-xx
Red (-)
VCC (+)
12/24V DC LED Driver
V- (-)
Black (-)
Blue (-)
White (-)
Brown (+)
Black (+)
Controller BL-CONT-IR-T80 BL-CONT-RF-T88 BL-CONT-DMX-LCI BL-DMX-USB BL-DMX-SRC144 BL-DMX-SRC-174 Power Supply BL-DMX-Touchpad
Controller Accessory BL-PWM-12/24V-3CH BL-AMP-T85 BL-DMX-SRC143 BL-DMX-CABLE-1.8M BL-DMX-CABLE-5M BL-DMX-CABLE-10M BL-DMX-CABLE-18AWG
Surge Protector BL-SP-277-20KA
RGB LED Ribbon with LCI Controller to DMX Master controller LED Ribbon
Blue (-)
Surge Protector
Green (-)
i
Red (-) VCC (+) Down Back
Green (gnd)
Red (+)
V+ (+) Enter Up
12/24V DC LED Driver
V- (-)
Black (-)
Blue (-)
White (-)
Brown (+)
Black (+)
Power Supply
RGB LED Ribbon with LCI Controller to DMX Master controller
DMX Controller
DMX Cable
LED Ribbon
Blue (-)
Surge Protector
Green (-)
i
Red (-) VCC (+)
Green (gnd)
Red (+)
V+ (+) Down Back
Enter Up
12/24V DC LED Driver
V- (-)
Black (-)
Blue (-)
White (-)
Brown (+)
Black (+)
Surge Protector
Green (-)
i
Red (-) VCC (+)
Enter Up
Green (gnd)
Red (+)
V+ (+) Down Back
12/24V DC LED Driver
V- (-)
Black (-)
Blue (-)
White (-)
Brown (+)
Black (+)
Surge
Green (-)
SurgeProtector Protector
RGB LED Ribbon with T80 Controller and Amplifier i Red (-) VCC (+)
R G B
LIGHT
V+
+
-
POWER
Enter
V+ (+) Down Back
V- (-) V+ (+)
DC 12/24V
V+ (+) Red (-) Green (-) Blue (-)
V- (-)
Power Supply
LED Ribbon
Blue (-)
RGB Controller Up
Power Supply
LED Ribbon
Blue (-)
DMX + DMX DMX gnd
Green (gnd)
Red (+)
Black (-)
12/24V DC LED Driver
12/24VBlack DC LED (-) Driver
Blue (-)
Blue (-)
Brown (+)
Brown (+)
Red (+)
Green (gnd)
White (-)
White (-)
Power Supply
Power Supply
Black (+)
Black (+)
LED Ribbon V+ (+) Red (-) Green (-) Blue (-) Surge Protector
Amplifier
Green (gnd)
-
POWER
Black (-)
R
LIGHT
V+
G
R
LIGHT
G
V+
+
B
B
DMX + DMX DMX gnd
Ordering
V- (-) V+ (+)
DC 12/24V
V+ (+) Red (-) Green (-) Blue (-)
12/24V DC LED Driver Red (+)
Blue (-)
White (-)
Brown (+)
Black (+)
LED Ribbon
Power Supply
Actual wire colours may vary - follow labels on the units Recommended to add 10% buffer when sizing power supply LED drivers require enclosures
Solid State Lighting is sensitive to power fluctuations Surge protection is highly recommended for all LED lighting products and should be on a designated circuit to protect against premature failure Lack of surge protection may void your warranty
111 - 8838 Heather St. Vancouver BC Canada V6P 3S8 Ph: 1-604-874-4405 • Fx: 1-604-321-0445 • www.bllighting.com • [email protected]
BL-RBN-ILL-24V-RGB - Page 2 December 26, 2013 12:03 PM Specifications subject to change without notice
