4' x 8' Flood and Drain Kit
www.hydro-flowproducts.com
4’ x 8’ Flood and Drain Kit A D
E
B
Parts List
Distributed exclusively by:
www.sunlightsupply.com
Ref A B C D E
Quantity 1 3 feet 3 feet 1 1
Description EcoPlus Ebb & Flow Fitting Kit Hydro Flow Vinyl Tubing Black 1/2” ID – 5/8” OD Hydro Flow Vinyl Tubing Black 3/4” ID – 1” OD EcoPlus Eco 633 Submersible Pump Titan Controls Apollo 7 - 24 Hour Digital Timer
C
Assembly Instructions 1. To install the two EcoPlus Ebb & Flow fittings, first locate the deepest sump port of the tray. Drill two 1.25” holes next to each other in the deepest sump area. Allow enough spacing so that the fittings will install next to each other. The tall fitting will be the outlet/overflow, while the short fitting will serve as the inlet from the pump. Make sure to use extensions for the overflow to ensure that you can raise water to the appropriate height without flooding. See Fig. A 2. After the two EcoPlus Ebb & Flow fittings are installed, attach the ½” vinyl tubing to the ½” inlet fitting (short fitting) located under the tray. Then, attach the ¾” vinyl tubing to the bottom of the outlet/overflow (tall fitting) located under the tray. Make sure that both tubes extend into the bottom of the reservoir under the tray. See Fig. B
Fig. A Fig. C
3. Attach the EcoPlus 633 submersible pump to the ½” tubing. Position pump in the bottom of the reservoir. Make sure there are no kinks in the tubing. See Fig. C. 4. Program Apollo 7 timer to desired setting and plug pump into Apollo 7 timer. DO NOT ACTIVATE PUMP WITHOUT WATER. See Fig. D. 5. Ensure that all parts are secure, then you can begin filling your reservoir and start growing.
Fig. B
Fig. D
4’ x 8’ Flood and Drain Kit A D
E
B
Parts List
Distributed exclusively by:
www.sunlightsupply.com
Ref A B C D E
Quantity 1 3 feet 3 feet 1 1
Description EcoPlus Ebb & Flow Fitting Kit Hydro Flow Vinyl Tubing Black 1/2” ID – 5/8” OD Hydro Flow Vinyl Tubing Black 3/4” ID – 1” OD EcoPlus Eco 633 Submersible Pump Titan Controls Apollo 7 - 24 Hour Digital Timer
C
Assembly Instructions 1. To install the two EcoPlus Ebb & Flow fittings, first locate the deepest sump port of the tray. Drill two 1.25” holes next to each other in the deepest sump area. Allow enough spacing so that the fittings will install next to each other. The tall fitting will be the outlet/overflow, while the short fitting will serve as the inlet from the pump. Make sure to use extensions for the overflow to ensure that you can raise water to the appropriate height without flooding. See Fig. A 2. After the two EcoPlus Ebb & Flow fittings are installed, attach the ½” vinyl tubing to the ½” inlet fitting (short fitting) located under the tray. Then, attach the ¾” vinyl tubing to the bottom of the outlet/overflow (tall fitting) located under the tray. Make sure that both tubes extend into the bottom of the reservoir under the tray. See Fig. B
Fig. A Fig. C
3. Attach the EcoPlus 633 submersible pump to the ½” tubing. Position pump in the bottom of the reservoir. Make sure there are no kinks in the tubing. See Fig. C. 4. Program Apollo 7 timer to desired setting and plug pump into Apollo 7 timer. DO NOT ACTIVATE PUMP WITHOUT WATER. See Fig. D. 5. Ensure that all parts are secure, then you can begin filling your reservoir and start growing.
Fig. B
Fig. D
