AdvanStik Insulation Adhesive
ADVANTECBP.COM
AdvanStik Insulation Adhesive Overview: AdvanStik Insulation Adhesive is a high performance, solvent free, two-component, construction-grade, low-rise polyurethane adhesive designed for the attachment of rigid insulation to various roof substrates. Strong: AdvanStik Insulation Adhesive provides exceptional wind uplift protection when bonding approved insulation boards to an approved substrate. All Temperature: Specially formulated for use in temperatures as low as 0° F., when properly stored. Quick Setting: At temperatures above freezing, properly stored AdvanStik Insulation Adhesive will lock insulation boards into place, ready for foot traffic, within 6-8 minutes of application. At temperatures below freezing, properly stored AdvanStik Insulation Adhesive will lock insulation boards into place, ready for foot traffic, within 8-12 minutes of application. Surface Preparation: All surfaces must be clean, sound and dry. Free of dust, dirt, debris, loose coating and any other condition that may prevent adhesion to the substrate. Conduct an adhesion test to all substrates prior to use. Contact Advantec Building Products for information regarding primers and surface treatments when adhering to fresh asphalt or substrates not listed above. Storage: Store AdvanStik Insulation Adhesive in original containers, in a dry area, protected from direct sunlight, at room temperatures 60° – 90° F. Extended storage at temperatures above 90° F may reduce shelf life. When applying AdvanStik Insulation Adhesive through a pump system, ensure internal material temperature is between 70° – 90° F, to avoid a poor mix. Material dispensed with the InvertaPress 3000 dispensing system will achieve a perfect mix in all temperatures. No special precautions required. Application: 1. Apply AdvanStik Insulation Adhesive in beads, minimum ½” wide, spaced 4”, 6” or 12” inches apart in accordance to roof system manufacturers requirements. 2. Allow adhesive to rise, set insulation boards into wet adhesive. If the adhesive has skinned, remove skinned material and apply fresh adhesive. 3. Takes steps to ensure insulation boards are in full contact with the substrate. Eliminate uneven surfaces. 4. Once the adhesive has set, the surface is ready for foot traffic and roof cover installation.
ADVANTEC BUILDING PRODUCTS 10357 Kinsman Rd. Unit G Newbury OH 44065 216-307-4497 [email protected]
Approved Substrates • Approved Insulation Boards • Concrete • Structural Lightweight Concrete • Gypsum • Cementitious Wood Fiber • Plywood/OSB • Wood Plank • Painted Steel • Galvanized Steel • Acoustical Steel • New or Scarified SPF • Smooth BUR • Gravel BUR • Mineral Cap Membrane • Granular Modified Bitumen • Sanded Smooth Modified Bitumen • Gravel Coal Tar BUR • Asphaltic Base Sheets • Vapor Retarders Approved Insulation/Roof Boards • Polyisocyanurate • Expanded Polystyrene • Extruded Polystyrene • Gypsum Roof Boards • Asphaltic Roof Boards • Oriented Strand Boards (OSB) • High Density Wood Fiber Packaging Standard • 9 Gallon InvertaPress Pac A & B Sets • 1500ml Quick Pack Cartridges Optional • 10 Gallon Bag in Box A & B Sets • 30 Gallon Barrel A & B Sets • 110 Gallon Barrel A & B Sets
ADVANTECBP.COM
AdvanStik Insulation Adhesive Precautions: • Review Material Safety Data Sheet prior to use. • AdvanStik Insulation Adhesive contains isocyanates, individuals who are sensitive or allergic to this ingredient should take necessary precautions or avoid use. • All surfaces to receive AdvanStik Insulation Adhesive must be clean, dry and free of dirt, dust, debris and any other condition that may prevent adhesion. • Conduct testing to ensure adhesion to the sub strate and insulation board. Allow fresh asphalt to age a minimum 30 days. • Contact Advantec Building Products for information regarding approved primers and surface treatments. • Ensure dispensing equipment is working properly before use. • Avoid contact with eyes. • Avoid breathing of vapors. Take necessary precautions in areas with limited ventilation. • Avoid contact with skin. Wash hands thoroughly after handling. • Set insulation boards into wet adhesive. If the adhesive has skinned over, remove it and apply fresh material to the substrate. Take steps to ensure insulation boards are in full contact with the substrate. Eliminate un-even surfaces. • Dispose in strict compliance with local, federal and state regulations.
ADVANTEC BUILDING PRODUCTS 10357 Kinsman Rd. Unit G Newbury OH 44065 216-307-4497 [email protected]
Coverage Rates 9 gal. InvertaPress Pac Surface/Bead Size
4” o.c.
6” o.c.
Smooth-Flat ½” Bead (Wet)
840 sf
1,300 sf 2,275 sf
12” o.c.
Insulation to Wood Fiber Deck 565 sf ¾” Bead (Wet)
870 sf
1,525 sf
Insulation to Gravel BUR 1” Bead (Wet)
650 sf
1,140 sf
420 sf
*Follow Roof System Manufacturer specifications regarding bead spacing, including perimeter and corner enhancement. InvertaPress Pac coverage based on 9 gal. A & B Set.
1500 ml. Quick Pack (4 per Box = 1.58 gal.) Surface/Bead Size
4” o.c.
6” o.c.
12” o.c.
Smooth-Flat ½” Bead (Wet)
175 sf
270 sf
475 sf
Insulation to Wood Fiber Deck 120 sf ¾” Bead (Wet)
185 sf
320 sf
Insulation to Gravel BUR 1” Bead (Wet)
135 sf
240 sf
90 sf
*InvertaPress Pac coverage based on 9 gal. A & B Set. Quick Pack coverage based on 4-1500 ml. cartridges (one box). Actual coverage rates may vary depending on local conditions
Properties
Part A (1)
Part B (2)
Mixing Ratio
1:1 Parts A & B by Volume
Viscosity (cps@77F)
300
300-500
Weight per Gallon
10.00 lbs./gal.
8.4 lbs./gal.
Shelf Life
12 months
12 months
Storage Temperature
60° - 90° F
Minimum Substrate Temperature
0° F
0° F
Minimum Ambient Temperature
0° F
0° F
-
-
AdvanStik Insulation Adhesive Overview: AdvanStik Insulation Adhesive is a high performance, solvent free, two-component, construction-grade, low-rise polyurethane adhesive designed for the attachment of rigid insulation to various roof substrates. Strong: AdvanStik Insulation Adhesive provides exceptional wind uplift protection when bonding approved insulation boards to an approved substrate. All Temperature: Specially formulated for use in temperatures as low as 0° F., when properly stored. Quick Setting: At temperatures above freezing, properly stored AdvanStik Insulation Adhesive will lock insulation boards into place, ready for foot traffic, within 6-8 minutes of application. At temperatures below freezing, properly stored AdvanStik Insulation Adhesive will lock insulation boards into place, ready for foot traffic, within 8-12 minutes of application. Surface Preparation: All surfaces must be clean, sound and dry. Free of dust, dirt, debris, loose coating and any other condition that may prevent adhesion to the substrate. Conduct an adhesion test to all substrates prior to use. Contact Advantec Building Products for information regarding primers and surface treatments when adhering to fresh asphalt or substrates not listed above. Storage: Store AdvanStik Insulation Adhesive in original containers, in a dry area, protected from direct sunlight, at room temperatures 60° – 90° F. Extended storage at temperatures above 90° F may reduce shelf life. When applying AdvanStik Insulation Adhesive through a pump system, ensure internal material temperature is between 70° – 90° F, to avoid a poor mix. Material dispensed with the InvertaPress 3000 dispensing system will achieve a perfect mix in all temperatures. No special precautions required. Application: 1. Apply AdvanStik Insulation Adhesive in beads, minimum ½” wide, spaced 4”, 6” or 12” inches apart in accordance to roof system manufacturers requirements. 2. Allow adhesive to rise, set insulation boards into wet adhesive. If the adhesive has skinned, remove skinned material and apply fresh adhesive. 3. Takes steps to ensure insulation boards are in full contact with the substrate. Eliminate uneven surfaces. 4. Once the adhesive has set, the surface is ready for foot traffic and roof cover installation.
ADVANTEC BUILDING PRODUCTS 10357 Kinsman Rd. Unit G Newbury OH 44065 216-307-4497 [email protected]
Approved Substrates • Approved Insulation Boards • Concrete • Structural Lightweight Concrete • Gypsum • Cementitious Wood Fiber • Plywood/OSB • Wood Plank • Painted Steel • Galvanized Steel • Acoustical Steel • New or Scarified SPF • Smooth BUR • Gravel BUR • Mineral Cap Membrane • Granular Modified Bitumen • Sanded Smooth Modified Bitumen • Gravel Coal Tar BUR • Asphaltic Base Sheets • Vapor Retarders Approved Insulation/Roof Boards • Polyisocyanurate • Expanded Polystyrene • Extruded Polystyrene • Gypsum Roof Boards • Asphaltic Roof Boards • Oriented Strand Boards (OSB) • High Density Wood Fiber Packaging Standard • 9 Gallon InvertaPress Pac A & B Sets • 1500ml Quick Pack Cartridges Optional • 10 Gallon Bag in Box A & B Sets • 30 Gallon Barrel A & B Sets • 110 Gallon Barrel A & B Sets
ADVANTECBP.COM
AdvanStik Insulation Adhesive Precautions: • Review Material Safety Data Sheet prior to use. • AdvanStik Insulation Adhesive contains isocyanates, individuals who are sensitive or allergic to this ingredient should take necessary precautions or avoid use. • All surfaces to receive AdvanStik Insulation Adhesive must be clean, dry and free of dirt, dust, debris and any other condition that may prevent adhesion. • Conduct testing to ensure adhesion to the sub strate and insulation board. Allow fresh asphalt to age a minimum 30 days. • Contact Advantec Building Products for information regarding approved primers and surface treatments. • Ensure dispensing equipment is working properly before use. • Avoid contact with eyes. • Avoid breathing of vapors. Take necessary precautions in areas with limited ventilation. • Avoid contact with skin. Wash hands thoroughly after handling. • Set insulation boards into wet adhesive. If the adhesive has skinned over, remove it and apply fresh material to the substrate. Take steps to ensure insulation boards are in full contact with the substrate. Eliminate un-even surfaces. • Dispose in strict compliance with local, federal and state regulations.
ADVANTEC BUILDING PRODUCTS 10357 Kinsman Rd. Unit G Newbury OH 44065 216-307-4497 [email protected]
Coverage Rates 9 gal. InvertaPress Pac Surface/Bead Size
4” o.c.
6” o.c.
Smooth-Flat ½” Bead (Wet)
840 sf
1,300 sf 2,275 sf
12” o.c.
Insulation to Wood Fiber Deck 565 sf ¾” Bead (Wet)
870 sf
1,525 sf
Insulation to Gravel BUR 1” Bead (Wet)
650 sf
1,140 sf
420 sf
*Follow Roof System Manufacturer specifications regarding bead spacing, including perimeter and corner enhancement. InvertaPress Pac coverage based on 9 gal. A & B Set.
1500 ml. Quick Pack (4 per Box = 1.58 gal.) Surface/Bead Size
4” o.c.
6” o.c.
12” o.c.
Smooth-Flat ½” Bead (Wet)
175 sf
270 sf
475 sf
Insulation to Wood Fiber Deck 120 sf ¾” Bead (Wet)
185 sf
320 sf
Insulation to Gravel BUR 1” Bead (Wet)
135 sf
240 sf
90 sf
*InvertaPress Pac coverage based on 9 gal. A & B Set. Quick Pack coverage based on 4-1500 ml. cartridges (one box). Actual coverage rates may vary depending on local conditions
Properties
Part A (1)
Part B (2)
Mixing Ratio
1:1 Parts A & B by Volume
Viscosity (cps@77F)
300
300-500
Weight per Gallon
10.00 lbs./gal.
8.4 lbs./gal.
Shelf Life
12 months
12 months
Storage Temperature
60° - 90° F
Minimum Substrate Temperature
0° F
0° F
Minimum Ambient Temperature
0° F
0° F
-
-
