aluminum electrolytic capacitors - TME
ALUMINUM ELECTROLYTIC CAPACITORS
ULH
Chip Type, High Voltage. High Reliability.
Chip type, High voltage and High Reliability. Load life of 4000 hours at +125°C. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2011/65/EU).
ULH
Long Life
ULT
Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current
Performance Characteristics
–40 to +125°C 160 to 450V 2.2 to 27µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.04CV+100 (µA). Measurement frequency : 120Hz at 20°C
Rated voltage (V) tan δ (MAX.)
Tangent of loss angle (tan δ)
160 0.20
200 0.20
250 0.25
400 0.25
450 0.30
Measurement frequency : 120Hz
Rated voltage (V) Impedance ratio Z–40°C / Z+20°C ZT / Z20 (MAX.)
Stability at Low Temperature
160
200
250
400
450
6
6
10
10
15 Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they Less than or equal to the initial specified value tan δ shall meet the characteristic requirements listed at right Less than or equal to the initial specified value Leakage current when they are removed from the plate. Black print on the case top.
Shelf Life
Resistance to soldering heat Marking
Chip Type
Type numbering system (Example : 400V 5.6µF)
(φ8 × 10L, φ10)
1
Positive C±0.2
0.3MAX.
Series
0.5MAX.
Plastic platform
Voltage(2G : 400V)
L±1.0
3
4
5
6
7
8
9 10
11 12 13 14
A±0.2 E A±0.2
B±0.2
φD±0.5
A2 5.6 2G LH
Capacitance
2
U L H 2 G 5 R 6 MN L 1 GS
Lot No. Trade mark
Capacitance change tan δ Leakage current
The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 4000 hours at 125°C.
Endurance
Taping code Configuration Capacitance tolerance (±20%) Rated capacitance (5.6μF)
H
Negative
Rated voltage (400V)
Pressure relief vent
Series name
(mm) φD × L
A B C E L H
8 × 10 10 × 10 2.9 3.2 10.3 8.3 10.3 8.3 4.5 3.1 10 10 0.8 to 1.1 0.8 to 1.1
Type
10 × 13.5 3.2 10.3 10.3 4.5 13.5 0.8 to 1.1
Voltage V
160
200
250
400
450
Code
2C
2D
2E
2G
2W
Dimensions Cap.(µF)
2.2 3.3 3.9 5.6 7.5 10 12 15 18 22 27
160 2C
V Code
2R2 3R3 3R9 5R6 7R5 100 120 150 180 220 270
200 2D
8 × 10
45
10 × 10
60
10 × 13.5
65
250 2E
8 × 10
45
10 × 10
60
10 × 13.5
65
400 2G
8 × 10
30
10 × 10 10 × 13.5
45 50
450 2W
8 × 10
30
10 × 10 10 × 13.5
45 50
8 × 10
20
10 × 10 10 × 13.5
35 40
Case size φ D × L (mm)
Rated ripple
Rated ripple current (mArms) at 125°C 120Hz
Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity.
Frequency coefficient of rated ripple current Frequency Coefficient
50 Hz 0.70
120 Hz 1.00
300 Hz 1.17
1 kHz 1.36
10 kHz or more 1.50
141
CAT.8100E
ULH
Chip Type, High Voltage. High Reliability.
Chip type, High voltage and High Reliability. Load life of 4000 hours at +125°C. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2011/65/EU).
ULH
Long Life
ULT
Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current
Performance Characteristics
–40 to +125°C 160 to 450V 2.2 to 27µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.04CV+100 (µA). Measurement frequency : 120Hz at 20°C
Rated voltage (V) tan δ (MAX.)
Tangent of loss angle (tan δ)
160 0.20
200 0.20
250 0.25
400 0.25
450 0.30
Measurement frequency : 120Hz
Rated voltage (V) Impedance ratio Z–40°C / Z+20°C ZT / Z20 (MAX.)
Stability at Low Temperature
160
200
250
400
450
6
6
10
10
15 Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they Less than or equal to the initial specified value tan δ shall meet the characteristic requirements listed at right Less than or equal to the initial specified value Leakage current when they are removed from the plate. Black print on the case top.
Shelf Life
Resistance to soldering heat Marking
Chip Type
Type numbering system (Example : 400V 5.6µF)
(φ8 × 10L, φ10)
1
Positive C±0.2
0.3MAX.
Series
0.5MAX.
Plastic platform
Voltage(2G : 400V)
L±1.0
3
4
5
6
7
8
9 10
11 12 13 14
A±0.2 E A±0.2
B±0.2
φD±0.5
A2 5.6 2G LH
Capacitance
2
U L H 2 G 5 R 6 MN L 1 GS
Lot No. Trade mark
Capacitance change tan δ Leakage current
The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 4000 hours at 125°C.
Endurance
Taping code Configuration Capacitance tolerance (±20%) Rated capacitance (5.6μF)
H
Negative
Rated voltage (400V)
Pressure relief vent
Series name
(mm) φD × L
A B C E L H
8 × 10 10 × 10 2.9 3.2 10.3 8.3 10.3 8.3 4.5 3.1 10 10 0.8 to 1.1 0.8 to 1.1
Type
10 × 13.5 3.2 10.3 10.3 4.5 13.5 0.8 to 1.1
Voltage V
160
200
250
400
450
Code
2C
2D
2E
2G
2W
Dimensions Cap.(µF)
2.2 3.3 3.9 5.6 7.5 10 12 15 18 22 27
160 2C
V Code
2R2 3R3 3R9 5R6 7R5 100 120 150 180 220 270
200 2D
8 × 10
45
10 × 10
60
10 × 13.5
65
250 2E
8 × 10
45
10 × 10
60
10 × 13.5
65
400 2G
8 × 10
30
10 × 10 10 × 13.5
45 50
450 2W
8 × 10
30
10 × 10 10 × 13.5
45 50
8 × 10
20
10 × 10 10 × 13.5
35 40
Case size φ D × L (mm)
Rated ripple
Rated ripple current (mArms) at 125°C 120Hz
Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity.
Frequency coefficient of rated ripple current Frequency Coefficient
50 Hz 0.70
120 Hz 1.00
300 Hz 1.17
1 kHz 1.36
10 kHz or more 1.50
141
CAT.8100E
