Amana Technical Information Gas Range
Amana Technical Information Gas Range ARG7600 ARG7800
P1141298N, P1143318N, P1143321N, P1143325N, P1133332N, P1143339N, P1143345N, P1143364N, P1143384N, P1143354N, P1143387N P1141299N, P1143319N, P1143322N, P1143326N, P1143340N, P1143346N, P1143365N, P1143385N, P1143355N, P1143388N
•Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. •This technical sheet replaces RT2310002 Rev. 8. •Refer to Service Manual RS2310002 for detailed installation, operating, testing, troubleshooting, and disassembly instructions. •Refer to Parts Manual RP2310029, RP2310030, RP2310040, RP2310043, RP2310055 and RP2310056 for part number information.
!
CAUTION
All safety information must be followed as provided in Service Manual RS2310002.
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Models Power Source Electrical rating Amperage Frequency Water Column Pressure Natural LP/Propane Surface Burner (BTU Nat./LP) Small Medium Two large Oven Burner (BTU Nat./LP) Bake Insta-Broil Oven Interior Dimensions in. (cm) Height Width Depth Product Exterior Dimensions in. (cm) Height overall Width Depth oven door closed with handle Clearance oven door Height of cooktop Weight lbs. (kg) Approximately shipping weight Features Glass backguard Exclusive one piece cast iron burner grates Square cast iron burner grates Frameless glass door with window Interior oven light Two oven racks 5 positions Exclusive Insta-Broil system Removable full width storage drawer Self-cleaning porcelain oven Touchmatic electronic range control Fluorescent panel light High performance sealed burners
April 2000
ARG7600
ARG7800
120 VAC 15 Amp maximum 60 Hz
120 VAC 15 Amp maximum 60 Hz
6 in. W.C.P. 10 in. W.C.P.
6 in. W.C.P. 10 in. W.C.P.
5,000/4,000 9,100/8,000 12,500/10,000
5,000/4,000 9,100/8,000 12,500/10,000
15,500/15,500 14,000/13,000
15,500/15,500 14,000/13,000
16 (41) 23 (58) 17 1/2 (44)
16 (41) 23 (58) 17 1/2 (44)
47 (119) 30 (76) 28 1/4 (72) 20 (51) 36 (91)
47 (119) 30 (76) 28 1/4 (72) 20 (51) 36 (91)
171 (78)
171 (78) X X X X X X X X X
1
X X X X X X X X X X X
RT2310002 Rev. 9
Component Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Illustration 31823701
Component Oven light socket
Test Procedure Remove one wire from receptacle and test resistance of terminals. Measure voltage at oven light.
0063997 ARG7600 0301491 ARG7600 0315858 ARG7800
Rocker switch
0305797
Door plunger switch NC
C NO
0316767
Door lock switch NC NO COM
31797301 31933401
Autolatch assembly with door plunger switch
Results Indicates continuity with good bulb screwed in. 120 VAC, see wiring diagram for terminal identification. If no voltage is present at oven light, check wiring and light switches.
Measure continuity of switch positions: Closed Open
Continuity, if not replace. Infinite, if not replace.
Remove switch from unit and measure the following points: C-NC C NO
Plunger in infinite, Plunger out continuity. Plunger in continuity, Plunger out infinite.
Test for voltage at terminals to chassis when in bake, broil, or clean mode. COM to chassis Only when latch is engaged: NC to chassis Disconnect wires and test for continuity per diagram.
120 VAC 120 VAC L1 L2
Refer to Parts Manual for correct autolatch switch associated with the correct manufacturing number.
NC NC COM NO COM NO
M 120 VAC Lock/Unlock Switch Motor
Door Switch
0071869
Ballast
Remove wires connected to ballast, and measure from terminal to terminal.
0071920
Starter
If light does not illuminate verify voltage to ballast.
0314907
Temperature sensor
Measure resistances.
Approximately 1100 O at room temperature 75ºF.
0309145− Bake 31940001-Bake 0316223− Broil 31939901-Broil
Norton ignitor
Test for voltage at terminals.
120 VAC
Test for the amount of amperage in the circuit. (Ignitor may glow but not have sufficent amperage to open valve).
3.2 − 3.6 Amps, If not replace.
0316211
Bake burner
RT2310002 Rev. 9
If infinite or zero resistance is indicated replace ballast. Resistance should be indicated, but not a direct short. If voltage is present, and ballast checks OK, replace starter.
Verify gas is supplied. Orifice adjusted for Natural or LP. Check for obstructions or contamination in ports.
2
April 2000
Component Testing Information
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Illustration 0060691
0316220
Component Broil burner
Gas valve
Test Procedure Verify gas is supplied. Proper orifice installed for Natural or LP. Check for damage to screen. Disconnect wiring to valve. Measure resistance on bake circuit. Measure resistance on broil circuit.
Results
Replace if punctured or torn. Continuity, If not replace. Continuity, If not replace.
! WARNING Do not attempt to open valve with 120 VAC. 0308866
Pressure regulator
Verify gas pressure (WCP).
6" Natural 10" LP/propane
If on LP service verify proper gas conversion. 0306428
Shut off valve
Check to verify gas supply is turned on.
0315960 5 K btu 0315961 9 K btu 0315962 12 K btu
270°valve
Verify gas is supplied. Orifice adjusted for Natural or LP. Adjust set screw for simmer control.
0316572
Spark 270°switch
Test for voltage at terminals.
120 VAC
Disconnect wiring and check for continuity in LITE position. Test for resistance of spark lead. Test ignitor to chassis. Check ground to burner head. Check cleanliness of burner cap and head Verify gas is supplied.
Continuity in LITE position.
Check for obstructions in burner ports.
Verify burner cap is positioned correctly. Shutter settings Nominal Tol. ± Test for voltage at terminals L and N.
.125" 1/8" .031" 1/32" 120 VAC
Check polarity and ground.
See wiring diagram
Carefully open the hinge fully, and insert a wooden dowel or screwdriver bit into opening. Remove top and bottom screws securing hinge. Slide hinge top towards rear of unit and guide hinge out through frame opening or storage drawer.
Do not place hands in hinge area when oven door is removed. Hinge can snap closed and pinch hands or fingers.
H
R G AA
0316773
Spark ignition electrode
0315769 5 K btu 0315768 9 K btu 0315767 12 K btu
Top surface burner
Venturi
0315154 L
Spark module 4 + 0 A
N
Clean as necessary.
B
A1
31715201 LH 31715202 RH
Opening
April 2000
Continuity No continuity from ignitor to chassis.
B1
Hinge
3
!
CAUTION
RT2310002 Rev. 9
Component Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Illustration 0315569 OVEN CANCEL
TIMER ON/OFF
DELAY OVEN ON CLEAN STOP TIME
CLOCK
STOP TIME
BAKE BROIL CLEAN LOCK
COOK TIME
CLEAN
BROIL
O N
Component ERC3 - Touchmatic electronic range control
BAKE
ERC3 Controlled
ERC3 Controlled
Quick test
Oven temperature adjustment
ERC3 Controlled
Twelve hour off
ERC3 Controlled
Child lock out
RT2310002 Rev. 9
Test Procedure F1 - Shorted pad button. F2 - Oven cavity over temperature. F3 - Open circuit in oven temperature sensor circuit. F4 - Shorted circuit in oven temperature circuit. F5 - Defective watchdog circuit in control. F7 - Failure of door lock switch sensing with door locked. F9 - Failure of door lock switching sensing with door unlocked. Apply power to oven press and hold COOKTIME pad for approximately 5 seconds within the first 5 minutes of power up. (It must be the first pad touched.) Press and hold individual pads to activate. Activation of the pad will stop when the pad is released.
Push BAKE pad. Push SLEW pad until an oven temperature greater than 500°F displays. Immediately push and hold BAKE pad until “00” displays, approximately 5 seconds. To decrease or increase oven temperature. Push SLEW pad until negative or positive numbers appear. Oven can be adjusted from -35° to +35°. To avoid over adjusting oven move temperature -5° each time. Push OVEN CANCEL button. Control will automatically cancel any cooking operation and remove all relay drives 12 hours after the last pad touched. Control input features will be disabled and display will indicate “OFF”, when BAKE and CLOCK are pushed simultaneously and held for 5 seconds. Control will return to normal operation by repeating the procedure.
4
Results Verify actuator operation. Check sensor wiring, sensor, and temperature limiter. Check sensor resistance and wiring. Check sensor resistance and wiring. Replace ERC3. Check latch switch and door motor. Check latch switch and door motor. Bake: Energizes bake element Broil: Energizes broil element Stop Time: Beeper ON and micro ID # Timer: No function Clock: All display segments lite Cook Time: Checksum and sensor temp Slew Pads: Sequences through display segments Clean: Door lock codes 3=lock and unlock contacts closed 2=lock closed, unlock open 1=lock open, unlock closed 0=both open Cancel: Exit quick test mode If functions do not perform as specified, replace ERC While increasing or decreasing oven temperature, this does not affect selfcleaning temperature.
Temperature adjustment will be retained even through a power failure.
April 2000
Component Specifications
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Converting Surface Burners for Use with LP/Propane 1. Remove 4 burner control knobs from range. • Exposes 2 screws on burner control panel. 2. Remove 2 screws from burner control panel. • Panel drops slightly after screws are removed. 3. Grasp bottom of burner control panel, gently lift and pull out panel until clear of burner valve stems. • After burner control panel clears valve stems, continue to roll panel until free from range. Set aside. • Gas valve and orifice hood are visible after burner control panel is removed.
Converting from Natural Gas to LP Gas
Converting the Insta-Broil 1. Remove or open oven door. 2. Remove screws securing Insta-Broil bracket. 3. Remove burner carefully, avoid damaging the ignitor to expose burner spud. Remove the #52 natural gas burner spud using a 5/16 socket wrench. Save #52 spud to reconvert if necessary in the furture. 4. Install the #58 LP/propane spud (wired to inlet pipe). 5. Replace Insta-Broil burner and holding screws. Converting Oven Burner for Use with LP/Propane 1. Remove storage drawer. 2. Locate and remove 2 screws attaching Z-shaped cover plate. • Cover plate located in center, rear of storage drawer cavity. • Removing cover plate exposes oven burner orifice and air shutter.
A B
D E C
A— B— C— D— E—
A C B
4. While facing range front, turn orifice hoods counterclockwise 1½ to 2 turns or until snug. • Use ½ inch open end or 90° offset open end wrench. • Do not over tighten orifice hoods. If orifice hoods are over tightened, gas supply can be cutoff or orifice hoods can damage LP pin. 5. Reassemble burner control panel after adjusting air shutter.
A— Air Shutter Screw B— Orifice Hood C— Air Shutter 3. Turn orifice hood clockwise until snug. • Do not over tighten orifice hoods. Orifice hoods can damage LP pin. 4. Replace cover plate and storage drawer.
Converting Pressure Regulator for LP/Propane 1. Remove pressure regulator cap using a 7/8 inch wrench. 2. Reverse pressure regulator cap. • Cap must show “LP”. 3. Place pressure regulator cap on pressure regulator and tighten.
Adjusting Burner Flame Properly adjusted burner flames are clean and blue with a distinct inner cone approximately ½ inch long. • If burner flame is blowing or noisy, reduce airflow to burner. • If burner flame is yellow and does not hold its shape, increase airflow to burner.
April 2000
Burner Control Knob Pivot Point Burner Control Panel Screw Orifice Hood
5
RT2310002 Rev. 9
Wiring Diagram and Schematic
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it.
HIGH VOLTAGE 22GA. 250C (4X)
L SPARK MODULE
WH N
4 MANIFOLD SWITCHES
VT
VT
A B A1 B1 or 1 2 3 4
VT
* *
BK
VT
BK
BU
OR
RIGHT SIDE FLUOR LIGHT SOCKET
YL
*
RF
*
*
*
BK
BK
OVEN LIGHT SWITCH
OVEN LIGHT WH
(N)
BK OR
BU WH RD 5 TERM CONN J2
ELECTRONIC RANGE CONTROL (ERC) 4 TERM CONN
J5
2
1 BR
VT
*
BK
SF2
OR
GY 4
3
*
BALLAST
5
GY
8
6 BU
GN
10
WH WH
BK
14 GA GN
BK
CHASSIS GND BACKGUARD GND BROIL IGNITOR
BR
4
1 BK
2
10 TERM CONN
J4
4
VT
1
BR
* *
VT BU
WH RD
BU
GY
12 SKT CAP
2
3
6
5
1
9
8
12
11
10
7
4
3
6
5
1
9
8
12
11
10
7
4
BR
*
SF2
VT
BK
GY
BU
WH RD
BU
3 PIN PLUG MAIN INPUT GN
RED
RD
ROUGE
ORANGE
OR
ORANGE
YELLOW
YL
JAUNE
GREEN
GN
VERT
BLUE
BU
BLEU
VIOLET
VT
VIOLET
BLACK
BK
NOIR
BROWN
BR
GRAY
GY
GRIS
WHITE
WH
BLANC
POWER CORD
VT 2 1
VT
OR
2 13
DR3
NO
2 SKT CONN WH/RD 1
3 SKT CAP BK
1
1
2
2
3
WH
WH
WH
BR
4.
*
DENOTES OPTIONAL EQUIPMENT AND RELATED WIRING NOT SUPPLIED ON SOME MODELS.
DIAGRAM - ELECTRICAL SHOCK HAZARD
DANGER
- DISCONNECT POWER AT MAIN
FUSE OR CIRCUIT BREAKER BEFORE SERVICING. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.
-RISQUE DE CHOC ELECTRIQUE -DEBRANCHER L'ALIMENTATION ELECTRIQUE. AVANT D'ENTRETENIR CETTE UNITE.
LE MANQUE DE RESPECT DE CETTE CONSIGNE POURRAIT AVOIR COMME RESULTAT UNE BLESSURE GRAVE OU MORTELLE.
ARG7600 RT2310002 Rev. 9
2. SEE SERIAL PLATE FOR INPUT RATINGS. 3. ALL REPLACEMENT WIRES MUST HAVE SAME RATINGS AS ORIGINAL WIRES.
BROIL BAKE IGNITOR
2
1. ALL INTERNAL WIRES ARE 18GA, 150C XL UNLESS OTHERWISE NOTED. SF2 IS SEW-2/SF2 200C RATED.
GAS VALVE
1
SENSOR
NOTES:
BAKE
2
1
WH
VT
2 PIN PLUG
2
2 PIN CONN
GN
3
*
BU
MARRON
WARNING
OR
DOOR LATCH SW
WH
2 SOCKET CAP
WH
NO COM
OVEN DOOR LIGHT SW
OR
VT SF2
NC BK
*
GY SF2 NC
COM
COULEUR
OR SF2
*
BU WH
COLOR
OR
VT
GY
2
*
COLOR SYMBOL
WH OR
12 PIN PLUG
DOOR LOCK MOTOR BR
BU
LEFT SIDE FLUOR LIGHT SOCKET
*
FLUOR LIGHT SWITCH BK
BK
*
STARTER
YL
RR
LR
LF
SURFACE ELECTRODES
*
YL
ARG7800 6
April 2000
Wiring Diagram and Schematic
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it.
LINE (BLACK)
NEUTRAL (WHITE)
GREEN
VT
MANIFOLD SWITCHES
L
N SPARK MODULE
or
A
B
1
2
A1
B1
3
4
SURFACE ELECTRODES
*
FLUORESCENT LIGHT SWITCH
*
YL
*
FLUORESCENT LIGHT (18W)
BALLAST
BU OR
YL
*
*
OVEN LIGHT SWITCH
STARTER
(N)
OR NO
C
BK DR1
1
3 NC
2
*
DR3
*
OVEN DOOR LIGHT SWITCH
OVEN LAMP
(4OW)
DR2 BU
GY
M J4-4
J4-1
DOOR LOCK MOTOR
J2-1 WH/RD J4-6
GND
K1 BU
J4-10
TEMPERATURE SENSOR
J2-2 120 VAC
J2-3
J4-8
VT DOOR LATCH SWITCH
J5-4
UNLOCK NO
K3 J5-1
COM
J2-4 GY K2
NC LOCK
J5-2 CIRCUIT BOARD BAKE IGNITOR VT
GAS VALVE VT
BROIL IGNITOR BR
OR J2-5
GAS VALVE BR
SCHEMATIC
OVEN CONDITIONS: OVEN BURNERS OFF, DOOR CLOSED AND UNLATCHED
31888502
ARG7600
April 2000
ARG7800
7
RT2310002 Rev. 9
Wiring Diagram and Schematic
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it.
ARG7600 P1143387N ARG7800 P1143388N RT2310002 Rev. 9
8
April 2000
P1141298N, P1143318N, P1143321N, P1143325N, P1133332N, P1143339N, P1143345N, P1143364N, P1143384N, P1143354N, P1143387N P1141299N, P1143319N, P1143322N, P1143326N, P1143340N, P1143346N, P1143365N, P1143385N, P1143355N, P1143388N
•Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. •This technical sheet replaces RT2310002 Rev. 8. •Refer to Service Manual RS2310002 for detailed installation, operating, testing, troubleshooting, and disassembly instructions. •Refer to Parts Manual RP2310029, RP2310030, RP2310040, RP2310043, RP2310055 and RP2310056 for part number information.
!
CAUTION
All safety information must be followed as provided in Service Manual RS2310002.
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Models Power Source Electrical rating Amperage Frequency Water Column Pressure Natural LP/Propane Surface Burner (BTU Nat./LP) Small Medium Two large Oven Burner (BTU Nat./LP) Bake Insta-Broil Oven Interior Dimensions in. (cm) Height Width Depth Product Exterior Dimensions in. (cm) Height overall Width Depth oven door closed with handle Clearance oven door Height of cooktop Weight lbs. (kg) Approximately shipping weight Features Glass backguard Exclusive one piece cast iron burner grates Square cast iron burner grates Frameless glass door with window Interior oven light Two oven racks 5 positions Exclusive Insta-Broil system Removable full width storage drawer Self-cleaning porcelain oven Touchmatic electronic range control Fluorescent panel light High performance sealed burners
April 2000
ARG7600
ARG7800
120 VAC 15 Amp maximum 60 Hz
120 VAC 15 Amp maximum 60 Hz
6 in. W.C.P. 10 in. W.C.P.
6 in. W.C.P. 10 in. W.C.P.
5,000/4,000 9,100/8,000 12,500/10,000
5,000/4,000 9,100/8,000 12,500/10,000
15,500/15,500 14,000/13,000
15,500/15,500 14,000/13,000
16 (41) 23 (58) 17 1/2 (44)
16 (41) 23 (58) 17 1/2 (44)
47 (119) 30 (76) 28 1/4 (72) 20 (51) 36 (91)
47 (119) 30 (76) 28 1/4 (72) 20 (51) 36 (91)
171 (78)
171 (78) X X X X X X X X X
1
X X X X X X X X X X X
RT2310002 Rev. 9
Component Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Illustration 31823701
Component Oven light socket
Test Procedure Remove one wire from receptacle and test resistance of terminals. Measure voltage at oven light.
0063997 ARG7600 0301491 ARG7600 0315858 ARG7800
Rocker switch
0305797
Door plunger switch NC
C NO
0316767
Door lock switch NC NO COM
31797301 31933401
Autolatch assembly with door plunger switch
Results Indicates continuity with good bulb screwed in. 120 VAC, see wiring diagram for terminal identification. If no voltage is present at oven light, check wiring and light switches.
Measure continuity of switch positions: Closed Open
Continuity, if not replace. Infinite, if not replace.
Remove switch from unit and measure the following points: C-NC C NO
Plunger in infinite, Plunger out continuity. Plunger in continuity, Plunger out infinite.
Test for voltage at terminals to chassis when in bake, broil, or clean mode. COM to chassis Only when latch is engaged: NC to chassis Disconnect wires and test for continuity per diagram.
120 VAC 120 VAC L1 L2
Refer to Parts Manual for correct autolatch switch associated with the correct manufacturing number.
NC NC COM NO COM NO
M 120 VAC Lock/Unlock Switch Motor
Door Switch
0071869
Ballast
Remove wires connected to ballast, and measure from terminal to terminal.
0071920
Starter
If light does not illuminate verify voltage to ballast.
0314907
Temperature sensor
Measure resistances.
Approximately 1100 O at room temperature 75ºF.
0309145− Bake 31940001-Bake 0316223− Broil 31939901-Broil
Norton ignitor
Test for voltage at terminals.
120 VAC
Test for the amount of amperage in the circuit. (Ignitor may glow but not have sufficent amperage to open valve).
3.2 − 3.6 Amps, If not replace.
0316211
Bake burner
RT2310002 Rev. 9
If infinite or zero resistance is indicated replace ballast. Resistance should be indicated, but not a direct short. If voltage is present, and ballast checks OK, replace starter.
Verify gas is supplied. Orifice adjusted for Natural or LP. Check for obstructions or contamination in ports.
2
April 2000
Component Testing Information
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Illustration 0060691
0316220
Component Broil burner
Gas valve
Test Procedure Verify gas is supplied. Proper orifice installed for Natural or LP. Check for damage to screen. Disconnect wiring to valve. Measure resistance on bake circuit. Measure resistance on broil circuit.
Results
Replace if punctured or torn. Continuity, If not replace. Continuity, If not replace.
! WARNING Do not attempt to open valve with 120 VAC. 0308866
Pressure regulator
Verify gas pressure (WCP).
6" Natural 10" LP/propane
If on LP service verify proper gas conversion. 0306428
Shut off valve
Check to verify gas supply is turned on.
0315960 5 K btu 0315961 9 K btu 0315962 12 K btu
270°valve
Verify gas is supplied. Orifice adjusted for Natural or LP. Adjust set screw for simmer control.
0316572
Spark 270°switch
Test for voltage at terminals.
120 VAC
Disconnect wiring and check for continuity in LITE position. Test for resistance of spark lead. Test ignitor to chassis. Check ground to burner head. Check cleanliness of burner cap and head Verify gas is supplied.
Continuity in LITE position.
Check for obstructions in burner ports.
Verify burner cap is positioned correctly. Shutter settings Nominal Tol. ± Test for voltage at terminals L and N.
.125" 1/8" .031" 1/32" 120 VAC
Check polarity and ground.
See wiring diagram
Carefully open the hinge fully, and insert a wooden dowel or screwdriver bit into opening. Remove top and bottom screws securing hinge. Slide hinge top towards rear of unit and guide hinge out through frame opening or storage drawer.
Do not place hands in hinge area when oven door is removed. Hinge can snap closed and pinch hands or fingers.
H
R G AA
0316773
Spark ignition electrode
0315769 5 K btu 0315768 9 K btu 0315767 12 K btu
Top surface burner
Venturi
0315154 L
Spark module 4 + 0 A
N
Clean as necessary.
B
A1
31715201 LH 31715202 RH
Opening
April 2000
Continuity No continuity from ignitor to chassis.
B1
Hinge
3
!
CAUTION
RT2310002 Rev. 9
Component Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Illustration 0315569 OVEN CANCEL
TIMER ON/OFF
DELAY OVEN ON CLEAN STOP TIME
CLOCK
STOP TIME
BAKE BROIL CLEAN LOCK
COOK TIME
CLEAN
BROIL
O N
Component ERC3 - Touchmatic electronic range control
BAKE
ERC3 Controlled
ERC3 Controlled
Quick test
Oven temperature adjustment
ERC3 Controlled
Twelve hour off
ERC3 Controlled
Child lock out
RT2310002 Rev. 9
Test Procedure F1 - Shorted pad button. F2 - Oven cavity over temperature. F3 - Open circuit in oven temperature sensor circuit. F4 - Shorted circuit in oven temperature circuit. F5 - Defective watchdog circuit in control. F7 - Failure of door lock switch sensing with door locked. F9 - Failure of door lock switching sensing with door unlocked. Apply power to oven press and hold COOKTIME pad for approximately 5 seconds within the first 5 minutes of power up. (It must be the first pad touched.) Press and hold individual pads to activate. Activation of the pad will stop when the pad is released.
Push BAKE pad. Push SLEW pad until an oven temperature greater than 500°F displays. Immediately push and hold BAKE pad until “00” displays, approximately 5 seconds. To decrease or increase oven temperature. Push SLEW pad until negative or positive numbers appear. Oven can be adjusted from -35° to +35°. To avoid over adjusting oven move temperature -5° each time. Push OVEN CANCEL button. Control will automatically cancel any cooking operation and remove all relay drives 12 hours after the last pad touched. Control input features will be disabled and display will indicate “OFF”, when BAKE and CLOCK are pushed simultaneously and held for 5 seconds. Control will return to normal operation by repeating the procedure.
4
Results Verify actuator operation. Check sensor wiring, sensor, and temperature limiter. Check sensor resistance and wiring. Check sensor resistance and wiring. Replace ERC3. Check latch switch and door motor. Check latch switch and door motor. Bake: Energizes bake element Broil: Energizes broil element Stop Time: Beeper ON and micro ID # Timer: No function Clock: All display segments lite Cook Time: Checksum and sensor temp Slew Pads: Sequences through display segments Clean: Door lock codes 3=lock and unlock contacts closed 2=lock closed, unlock open 1=lock open, unlock closed 0=both open Cancel: Exit quick test mode If functions do not perform as specified, replace ERC While increasing or decreasing oven temperature, this does not affect selfcleaning temperature.
Temperature adjustment will be retained even through a power failure.
April 2000
Component Specifications
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it. Converting Surface Burners for Use with LP/Propane 1. Remove 4 burner control knobs from range. • Exposes 2 screws on burner control panel. 2. Remove 2 screws from burner control panel. • Panel drops slightly after screws are removed. 3. Grasp bottom of burner control panel, gently lift and pull out panel until clear of burner valve stems. • After burner control panel clears valve stems, continue to roll panel until free from range. Set aside. • Gas valve and orifice hood are visible after burner control panel is removed.
Converting from Natural Gas to LP Gas
Converting the Insta-Broil 1. Remove or open oven door. 2. Remove screws securing Insta-Broil bracket. 3. Remove burner carefully, avoid damaging the ignitor to expose burner spud. Remove the #52 natural gas burner spud using a 5/16 socket wrench. Save #52 spud to reconvert if necessary in the furture. 4. Install the #58 LP/propane spud (wired to inlet pipe). 5. Replace Insta-Broil burner and holding screws. Converting Oven Burner for Use with LP/Propane 1. Remove storage drawer. 2. Locate and remove 2 screws attaching Z-shaped cover plate. • Cover plate located in center, rear of storage drawer cavity. • Removing cover plate exposes oven burner orifice and air shutter.
A B
D E C
A— B— C— D— E—
A C B
4. While facing range front, turn orifice hoods counterclockwise 1½ to 2 turns or until snug. • Use ½ inch open end or 90° offset open end wrench. • Do not over tighten orifice hoods. If orifice hoods are over tightened, gas supply can be cutoff or orifice hoods can damage LP pin. 5. Reassemble burner control panel after adjusting air shutter.
A— Air Shutter Screw B— Orifice Hood C— Air Shutter 3. Turn orifice hood clockwise until snug. • Do not over tighten orifice hoods. Orifice hoods can damage LP pin. 4. Replace cover plate and storage drawer.
Converting Pressure Regulator for LP/Propane 1. Remove pressure regulator cap using a 7/8 inch wrench. 2. Reverse pressure regulator cap. • Cap must show “LP”. 3. Place pressure regulator cap on pressure regulator and tighten.
Adjusting Burner Flame Properly adjusted burner flames are clean and blue with a distinct inner cone approximately ½ inch long. • If burner flame is blowing or noisy, reduce airflow to burner. • If burner flame is yellow and does not hold its shape, increase airflow to burner.
April 2000
Burner Control Knob Pivot Point Burner Control Panel Screw Orifice Hood
5
RT2310002 Rev. 9
Wiring Diagram and Schematic
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it.
HIGH VOLTAGE 22GA. 250C (4X)
L SPARK MODULE
WH N
4 MANIFOLD SWITCHES
VT
VT
A B A1 B1 or 1 2 3 4
VT
* *
BK
VT
BK
BU
OR
RIGHT SIDE FLUOR LIGHT SOCKET
YL
*
RF
*
*
*
BK
BK
OVEN LIGHT SWITCH
OVEN LIGHT WH
(N)
BK OR
BU WH RD 5 TERM CONN J2
ELECTRONIC RANGE CONTROL (ERC) 4 TERM CONN
J5
2
1 BR
VT
*
BK
SF2
OR
GY 4
3
*
BALLAST
5
GY
8
6 BU
GN
10
WH WH
BK
14 GA GN
BK
CHASSIS GND BACKGUARD GND BROIL IGNITOR
BR
4
1 BK
2
10 TERM CONN
J4
4
VT
1
BR
* *
VT BU
WH RD
BU
GY
12 SKT CAP
2
3
6
5
1
9
8
12
11
10
7
4
3
6
5
1
9
8
12
11
10
7
4
BR
*
SF2
VT
BK
GY
BU
WH RD
BU
3 PIN PLUG MAIN INPUT GN
RED
RD
ROUGE
ORANGE
OR
ORANGE
YELLOW
YL
JAUNE
GREEN
GN
VERT
BLUE
BU
BLEU
VIOLET
VT
VIOLET
BLACK
BK
NOIR
BROWN
BR
GRAY
GY
GRIS
WHITE
WH
BLANC
POWER CORD
VT 2 1
VT
OR
2 13
DR3
NO
2 SKT CONN WH/RD 1
3 SKT CAP BK
1
1
2
2
3
WH
WH
WH
BR
4.
*
DENOTES OPTIONAL EQUIPMENT AND RELATED WIRING NOT SUPPLIED ON SOME MODELS.
DIAGRAM - ELECTRICAL SHOCK HAZARD
DANGER
- DISCONNECT POWER AT MAIN
FUSE OR CIRCUIT BREAKER BEFORE SERVICING. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.
-RISQUE DE CHOC ELECTRIQUE -DEBRANCHER L'ALIMENTATION ELECTRIQUE. AVANT D'ENTRETENIR CETTE UNITE.
LE MANQUE DE RESPECT DE CETTE CONSIGNE POURRAIT AVOIR COMME RESULTAT UNE BLESSURE GRAVE OU MORTELLE.
ARG7600 RT2310002 Rev. 9
2. SEE SERIAL PLATE FOR INPUT RATINGS. 3. ALL REPLACEMENT WIRES MUST HAVE SAME RATINGS AS ORIGINAL WIRES.
BROIL BAKE IGNITOR
2
1. ALL INTERNAL WIRES ARE 18GA, 150C XL UNLESS OTHERWISE NOTED. SF2 IS SEW-2/SF2 200C RATED.
GAS VALVE
1
SENSOR
NOTES:
BAKE
2
1
WH
VT
2 PIN PLUG
2
2 PIN CONN
GN
3
*
BU
MARRON
WARNING
OR
DOOR LATCH SW
WH
2 SOCKET CAP
WH
NO COM
OVEN DOOR LIGHT SW
OR
VT SF2
NC BK
*
GY SF2 NC
COM
COULEUR
OR SF2
*
BU WH
COLOR
OR
VT
GY
2
*
COLOR SYMBOL
WH OR
12 PIN PLUG
DOOR LOCK MOTOR BR
BU
LEFT SIDE FLUOR LIGHT SOCKET
*
FLUOR LIGHT SWITCH BK
BK
*
STARTER
YL
RR
LR
LF
SURFACE ELECTRODES
*
YL
ARG7800 6
April 2000
Wiring Diagram and Schematic
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it.
LINE (BLACK)
NEUTRAL (WHITE)
GREEN
VT
MANIFOLD SWITCHES
L
N SPARK MODULE
or
A
B
1
2
A1
B1
3
4
SURFACE ELECTRODES
*
FLUORESCENT LIGHT SWITCH
*
YL
*
FLUORESCENT LIGHT (18W)
BALLAST
BU OR
YL
*
*
OVEN LIGHT SWITCH
STARTER
(N)
OR NO
C
BK DR1
1
3 NC
2
*
DR3
*
OVEN DOOR LIGHT SWITCH
OVEN LAMP
(4OW)
DR2 BU
GY
M J4-4
J4-1
DOOR LOCK MOTOR
J2-1 WH/RD J4-6
GND
K1 BU
J4-10
TEMPERATURE SENSOR
J2-2 120 VAC
J2-3
J4-8
VT DOOR LATCH SWITCH
J5-4
UNLOCK NO
K3 J5-1
COM
J2-4 GY K2
NC LOCK
J5-2 CIRCUIT BOARD BAKE IGNITOR VT
GAS VALVE VT
BROIL IGNITOR BR
OR J2-5
GAS VALVE BR
SCHEMATIC
OVEN CONDITIONS: OVEN BURNERS OFF, DOOR CLOSED AND UNLATCHED
31888502
ARG7600
April 2000
ARG7800
7
RT2310002 Rev. 9
Wiring Diagram and Schematic
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven before servicing, unless testing requires it.
ARG7600 P1143387N ARG7800 P1143388N RT2310002 Rev. 9
8
April 2000
