Assembly
intermix
DEUCE CONFERENCE TABLE assembly instructions
intermix
DEUCE CONFERENCE TABLE assembly instructions
EUCE CONFERENCE TABLE ASSEMBLY
CENTER BASE ASSEMBLY
a
STEP ONE:
is no
Place conference work surface bottom side up on a nonmarring surface. On 2 piece tops, pull both halves together so there is no gap between them, and the edges are flush.
shown.
mblies.
Do not fasten work surfaces together at this time. Place bases near chalk marks and orient them as shown. CHALK MARK
Larger tables will use one or two center base assemblies.
STEP TWO: Slide bridge rail onto the hub collars of base assemblies. Attach in place by using two (2) 1/2” phillips machine screws on each end of the bridge rail.
mblies.
ne screws
Repeat for any additional base assemblies.
2 1
BRIDGE RAIL
intermix
DEUCE CONFERENCE TABLE ASSEMBLY DEUCE CONFERENCE TABLE ASSEMBLY
inside the inside
mblies and semblies and l holes are n all holes are
PILOT BORE BORE 8PILOT PLACES 8 PLACES PER BASE PER BASE
DEUCE CONFERENCE TABLE assembly instructions
STEP THREE: Align base assemblies precisely to the inside of chalk marks.
holes where ot holes where
Mark hole locations for all base assemblies and set base assembly to the side when all holes are marked. Bore 9/64” diameter x 3/4” deep pilot holes where marked.
is is eble table
STEP FOUR:
ourfour (4) (4) ert dge.
Set base assembly upright where table is to be located.
embly, assembly, necting connecting er.
For two piece work surfaces, insert four (4) dowels in holes on connecting edge. Set both halves of table on base assembly, align dowels with holes on other connecting edge and pull both halves together.
Part Part #:#:
intermix
DEUCE CONFERENCE TABLE assembly instructions
EUCE EUCE CONFERENCE CONFERENCE TABLE TABLE ASSEMBLY ASSEMBLY EUCE CONFERENCE TABLE ASSEMBLY
ng two (2) ng two (2) edges. edges. ng two (2) edges.
STEP FIVE: Connect two halves to work surface together by using two (2) joint fasteners in routed-out sections on connecting edges. Tighten joint fasteners with 7/16” wrench.
JOINT FASTENER JOINT FASTENER JOINT FASTENER
stener stener ly. ly. stener ly.
STEP SIX: Access third routed-out section to install third joint fastener by sliding work surface length-wise on base assembly.
STEP SEVEN:
back to it's back to it's are aligned are aligned back to it's are aligned ht (8) #12 ht (8) #12
After installing all joint fasteners, slide work surface back to its original position so the holes in the mounting plates are aligned with the pilot holes.
ht (8) #12
Fasten work surface to mounting plates by using eight (8) #12 x 1” phillips pan head screws per base.
NFERENCE NFERENCE TABLE TABLE ASSEMBLY ASSEMBLY 1204 east sixth street NFERENCE TABLE ASSEMBLY huntingburg, in 47542 Part #: Part #: Part #:
firstoffice.com
telephone 800 983 4415 fax orders 812 683 7256 fax cs 812 683 7155
01-09-13
DEUCE CONFERENCE TABLE assembly instructions
intermix
DEUCE CONFERENCE TABLE assembly instructions
EUCE CONFERENCE TABLE ASSEMBLY
CENTER BASE ASSEMBLY
a
STEP ONE:
is no
Place conference work surface bottom side up on a nonmarring surface. On 2 piece tops, pull both halves together so there is no gap between them, and the edges are flush.
shown.
mblies.
Do not fasten work surfaces together at this time. Place bases near chalk marks and orient them as shown. CHALK MARK
Larger tables will use one or two center base assemblies.
STEP TWO: Slide bridge rail onto the hub collars of base assemblies. Attach in place by using two (2) 1/2” phillips machine screws on each end of the bridge rail.
mblies.
ne screws
Repeat for any additional base assemblies.
2 1
BRIDGE RAIL
intermix
DEUCE CONFERENCE TABLE ASSEMBLY DEUCE CONFERENCE TABLE ASSEMBLY
inside the inside
mblies and semblies and l holes are n all holes are
PILOT BORE BORE 8PILOT PLACES 8 PLACES PER BASE PER BASE
DEUCE CONFERENCE TABLE assembly instructions
STEP THREE: Align base assemblies precisely to the inside of chalk marks.
holes where ot holes where
Mark hole locations for all base assemblies and set base assembly to the side when all holes are marked. Bore 9/64” diameter x 3/4” deep pilot holes where marked.
is is eble table
STEP FOUR:
ourfour (4) (4) ert dge.
Set base assembly upright where table is to be located.
embly, assembly, necting connecting er.
For two piece work surfaces, insert four (4) dowels in holes on connecting edge. Set both halves of table on base assembly, align dowels with holes on other connecting edge and pull both halves together.
Part Part #:#:
intermix
DEUCE CONFERENCE TABLE assembly instructions
EUCE EUCE CONFERENCE CONFERENCE TABLE TABLE ASSEMBLY ASSEMBLY EUCE CONFERENCE TABLE ASSEMBLY
ng two (2) ng two (2) edges. edges. ng two (2) edges.
STEP FIVE: Connect two halves to work surface together by using two (2) joint fasteners in routed-out sections on connecting edges. Tighten joint fasteners with 7/16” wrench.
JOINT FASTENER JOINT FASTENER JOINT FASTENER
stener stener ly. ly. stener ly.
STEP SIX: Access third routed-out section to install third joint fastener by sliding work surface length-wise on base assembly.
STEP SEVEN:
back to it's back to it's are aligned are aligned back to it's are aligned ht (8) #12 ht (8) #12
After installing all joint fasteners, slide work surface back to its original position so the holes in the mounting plates are aligned with the pilot holes.
ht (8) #12
Fasten work surface to mounting plates by using eight (8) #12 x 1” phillips pan head screws per base.
NFERENCE NFERENCE TABLE TABLE ASSEMBLY ASSEMBLY 1204 east sixth street NFERENCE TABLE ASSEMBLY huntingburg, in 47542 Part #: Part #: Part #:
firstoffice.com
telephone 800 983 4415 fax orders 812 683 7256 fax cs 812 683 7155
01-09-13
