Audiovox CDM-8900 Logic Board Replacement
Audiovox CDM-8900 Logic Board Replacement
Audiovox CDM-8900 Logic Board Replacement Written By: Aaron Shaw
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Audiovox CDM-8900 Logic Board Replacement
INTRODUCTION Here is how you replace the logic board from the cell phone.
TOOLS:
PARTS:
Phillips #00 Screwdriver (1)
Audiovox CDM-8900 Logicboard (1)
iFixit Opening Tools (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Audiovox CDM-8900 Logic Board Replacement
Step 1 — Battery
Hold the phone in one hand, slide latch, and pull to remove the battery.
Step 2 — Antenna
Grasp antenna at its base and unscrew.
Remove the antenna along with its plastic casing from inside the battery housing. Keep the antenna in the plastic casing for reassembly.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Audiovox CDM-8900 Logic Board Replacement
Step 3 — Logic Board
Remove small rubber insert from top of phone to access the top screw.
Warning: Screws are very small and may be difficult to see while unscrewing.
Unscrew all five (5) screws on the back of cell phone.
If screws do not remove after fully unthreading, gently invert and tap phone in hand until the screws come loose.
Step 4
Wedge back plate away from cell phone using the leverage from the plastic spudger.
The volume control button on the left side of the phone will be loose. Make sure to carefully reinsert during reassembly.
Detach logic board from LCD screen connector by gently detaching the small copper plate on the top right of the logic board. (shown circled in blue and detached)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
Audiovox CDM-8900 Logic Board Replacement
Step 5
Pop the logic board out from the front of the cell phone.
Before reassembly, be sure keypad is lined up with logic board.
Before reassembly, be sure camera lens is properly aligned at the top of the logic board and volume controls are in place.
Step 6 — Camera
Grasp camera.
Slide camera out of slot from logic board.
Camera is difficult to reassemble; there is a white clip for easy camera replacement. Verify that you orient the camera correctly when reinserting.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Audiovox CDM-8900 Logic Board Replacement
Step 7 — Logic Board
Attach camera to new logic board.
Follow steps in reverse order to replace logic board.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-11 04:05:16 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
Audiovox CDM-8900 Logic Board Replacement Written By: Aaron Shaw
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Audiovox CDM-8900 Logic Board Replacement
INTRODUCTION Here is how you replace the logic board from the cell phone.
TOOLS:
PARTS:
Phillips #00 Screwdriver (1)
Audiovox CDM-8900 Logicboard (1)
iFixit Opening Tools (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Audiovox CDM-8900 Logic Board Replacement
Step 1 — Battery
Hold the phone in one hand, slide latch, and pull to remove the battery.
Step 2 — Antenna
Grasp antenna at its base and unscrew.
Remove the antenna along with its plastic casing from inside the battery housing. Keep the antenna in the plastic casing for reassembly.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Audiovox CDM-8900 Logic Board Replacement
Step 3 — Logic Board
Remove small rubber insert from top of phone to access the top screw.
Warning: Screws are very small and may be difficult to see while unscrewing.
Unscrew all five (5) screws on the back of cell phone.
If screws do not remove after fully unthreading, gently invert and tap phone in hand until the screws come loose.
Step 4
Wedge back plate away from cell phone using the leverage from the plastic spudger.
The volume control button on the left side of the phone will be loose. Make sure to carefully reinsert during reassembly.
Detach logic board from LCD screen connector by gently detaching the small copper plate on the top right of the logic board. (shown circled in blue and detached)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
Audiovox CDM-8900 Logic Board Replacement
Step 5
Pop the logic board out from the front of the cell phone.
Before reassembly, be sure keypad is lined up with logic board.
Before reassembly, be sure camera lens is properly aligned at the top of the logic board and volume controls are in place.
Step 6 — Camera
Grasp camera.
Slide camera out of slot from logic board.
Camera is difficult to reassemble; there is a white clip for easy camera replacement. Verify that you orient the camera correctly when reinserting.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Audiovox CDM-8900 Logic Board Replacement
Step 7 — Logic Board
Attach camera to new logic board.
Follow steps in reverse order to replace logic board.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-11 04:05:16 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
