bollard installation instructions - Energy Avenue
BOLLARD INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
ROUND BOLLARD
SQUARE BOLLARD
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
LOCATION
CAUTION: Before mounting, make sure to align Bollard Base in the orientation that will result in the desired Bollard Fixture orientation. 1. The Bollard should be mounted to a firm level surface. 2. Anchor bolts may be used in new concrete installations. Use the template provided. 3. For all other applications use anchors suitable for the mounting surface.
ANCHOR BOLTS INSTALLATION
CAUTION: Install according to all applicable local codes. Install four Anchor Bolts in concrete foundation (by others) using the template provided. Bollard Base may also be used as the template. Bollard Base
BOLLARD BASE
1. Place the Bollard Base over Anchor Bolts. 2. Loosely tighten the Washers, Lock washers and Nuts provided. Level the Bollard Base with provided Leveling screws. Tighten all nuts and screws. 3. Be sure supply leads extend far enough to make fixture connections. Make the wiring connections with UL approved connectors. 4. Slide the Bollard over on Bollard Base lined up with the grooves. Be sure to check the LED position on the Bollard. 5. Use the four set screws to secure the Bollard to the Bollard Base. Set Screws Nuts Lockwasher Washer
Anchor Bolts
Bollard Base
Anchor Bolts
Levelling Screws
Concrete Conduit
BOLLARD INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized. 1. Clean lens with non-abrasive cleaning solution
WIRING
Universal driver permits 120V to 277V, 50 or 60Hz. 1. Connect the bare copper Ground wire from fixture to supply ground. 2. Connect the black fixture lead to the (+) LINE supply lead.
2. Do not open fixture to clean the LED.
TROUBLESHOOTING 1. Check that the line voltage at fixture is correct. Refer to wiring directions.
3. Connect the white fixture lead to the (-) COMMON supply lead.
(+)LINE
BLACK
(-)COMMON
WHITE
2. Is the fixture grounded properly?
ACCESSORIES
Bollard base Retro kit: Suffix “Y” = Suffix “N” =
GROUND
BOLBASE24 RETRO
LIGHT FIXTURE
GROUND
Warm 3000K LED Neutral 4000K LED,
BLED24 Square Bollard 24W Cool LED
BLEDR24 Round Bollard 24W Cool LED
BOLLARD Round: US pat. D675,766, CA Pat. pending, CN ZL201230350184.6, MX pat. pending, TX: pat.pending BOLLARD Square:.US pat. D675,767, CA Pat. pending, CN ZL201230350185.0, MX pat. pending, TX: pat.pending
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
Easy Installation & Product Help ©2012 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
BOLLARD IN 0913
Tech Help Line Call our experts 888 RAB-1000
rabweb.com Visit our website for product info
email Answered promptly [email protected]
BOLLARD INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
ANCHOR BOLT TEMPLATE FOR BLED BOLLARD
Drawing not to scale. Use the actual mounting plate as your template.
1.5” 39.94mm
45º
45.0°
1.021” 25.94mm
1.5” 39.94mm
Ø 2.45” 60.02mm HOLE FOR CONDUIT
1.021” 25.94mm
Ø 3.75” 95.25mm
1.45” 36.95mm
39.1º
Ø 2.45” 60.02mm HOLE FOR CONDUIT
1.183” 30.05mm
1.183” 30.05mm
Ø 3.75” 95.25mm 4.404” 111.86mm
BOLLARD INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
Anchor bolt template for bled bollard
Drawing not to scale. Use the actual mounting plate as your template.
1.5” 39.94mm
45º
45.0°
1.021” 25.94mm
1.5” 39.94mm
Ø 2.45” 60.02mm HOLE FOR CONDUIT
1.021” 25.94mm
Ø 3.75” 95.25mm
1.45” 36.95mm
39.1º
Ø 2.45” 60.02mm HOLE FOR CONDUIT
1.183” 30.05mm
1.183” 30.05mm
Ø 3.75” 95.25mm 4.404” 111.86mm
BOLBASE RETRO24 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable
parts inside.
BOLBASE24 RETRO
CAUTION: Before drilling and mounting, make sure to align Bollard Base Retro in the orientation that will result in the desired Bollard Fixture orientation. Retrofit Bollard Base for BLED12 and BLED24 for retrofit application for existing concrete or base (Bollards sold separately). 1. Drill the surface in the drilling location shown in the detailed dimensional drawings. 2. Feed the conduit through 2.45” dia hole of the Retrofit Bottom Plate. Place the Retrofit Bottom Plate on the mounting surface and tighten it with 4 screws. 3. Place Retrofit Top Plate on Retrofit Bottom Plate and tighten it with Set Screws. 4. Install Bollard on the Retrofit Top Plate using appropriate hardware.
Bollard Base
Retrofit Top Plate Set Screws Retrofit Bottom Plate Conduit
Mounting Surface
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
BOLBASE RETRO24 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
base plate template
Template not to scale. Use actual plate as template. CAUTION: Before drilling and mounting, make sure to align Bollard Base Retro in the orientation that will result in the desired Bollard Fixture orientation. .257 [ 6,53 ] 8.547 [ 217,1 ]
4.500 [ 114,3 ] 45.0°
2.298 [58,37]
2.747 [69,77]
50.0°
6.500 [ 165,1 ]
ROUND BOLLARD
SQUARE BOLLARD
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
LOCATION
CAUTION: Before mounting, make sure to align Bollard Base in the orientation that will result in the desired Bollard Fixture orientation. 1. The Bollard should be mounted to a firm level surface. 2. Anchor bolts may be used in new concrete installations. Use the template provided. 3. For all other applications use anchors suitable for the mounting surface.
ANCHOR BOLTS INSTALLATION
CAUTION: Install according to all applicable local codes. Install four Anchor Bolts in concrete foundation (by others) using the template provided. Bollard Base may also be used as the template. Bollard Base
BOLLARD BASE
1. Place the Bollard Base over Anchor Bolts. 2. Loosely tighten the Washers, Lock washers and Nuts provided. Level the Bollard Base with provided Leveling screws. Tighten all nuts and screws. 3. Be sure supply leads extend far enough to make fixture connections. Make the wiring connections with UL approved connectors. 4. Slide the Bollard over on Bollard Base lined up with the grooves. Be sure to check the LED position on the Bollard. 5. Use the four set screws to secure the Bollard to the Bollard Base. Set Screws Nuts Lockwasher Washer
Anchor Bolts
Bollard Base
Anchor Bolts
Levelling Screws
Concrete Conduit
BOLLARD INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized. 1. Clean lens with non-abrasive cleaning solution
WIRING
Universal driver permits 120V to 277V, 50 or 60Hz. 1. Connect the bare copper Ground wire from fixture to supply ground. 2. Connect the black fixture lead to the (+) LINE supply lead.
2. Do not open fixture to clean the LED.
TROUBLESHOOTING 1. Check that the line voltage at fixture is correct. Refer to wiring directions.
3. Connect the white fixture lead to the (-) COMMON supply lead.
(+)LINE
BLACK
(-)COMMON
WHITE
2. Is the fixture grounded properly?
ACCESSORIES
Bollard base Retro kit: Suffix “Y” = Suffix “N” =
GROUND
BOLBASE24 RETRO
LIGHT FIXTURE
GROUND
Warm 3000K LED Neutral 4000K LED,
BLED24 Square Bollard 24W Cool LED
BLEDR24 Round Bollard 24W Cool LED
BOLLARD Round: US pat. D675,766, CA Pat. pending, CN ZL201230350184.6, MX pat. pending, TX: pat.pending BOLLARD Square:.US pat. D675,767, CA Pat. pending, CN ZL201230350185.0, MX pat. pending, TX: pat.pending
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
Easy Installation & Product Help ©2012 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
BOLLARD IN 0913
Tech Help Line Call our experts 888 RAB-1000
rabweb.com Visit our website for product info
email Answered promptly [email protected]
BOLLARD INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
ANCHOR BOLT TEMPLATE FOR BLED BOLLARD
Drawing not to scale. Use the actual mounting plate as your template.
1.5” 39.94mm
45º
45.0°
1.021” 25.94mm
1.5” 39.94mm
Ø 2.45” 60.02mm HOLE FOR CONDUIT
1.021” 25.94mm
Ø 3.75” 95.25mm
1.45” 36.95mm
39.1º
Ø 2.45” 60.02mm HOLE FOR CONDUIT
1.183” 30.05mm
1.183” 30.05mm
Ø 3.75” 95.25mm 4.404” 111.86mm
BOLLARD INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
Anchor bolt template for bled bollard
Drawing not to scale. Use the actual mounting plate as your template.
1.5” 39.94mm
45º
45.0°
1.021” 25.94mm
1.5” 39.94mm
Ø 2.45” 60.02mm HOLE FOR CONDUIT
1.021” 25.94mm
Ø 3.75” 95.25mm
1.45” 36.95mm
39.1º
Ø 2.45” 60.02mm HOLE FOR CONDUIT
1.183” 30.05mm
1.183” 30.05mm
Ø 3.75” 95.25mm 4.404” 111.86mm
BOLBASE RETRO24 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable
parts inside.
BOLBASE24 RETRO
CAUTION: Before drilling and mounting, make sure to align Bollard Base Retro in the orientation that will result in the desired Bollard Fixture orientation. Retrofit Bollard Base for BLED12 and BLED24 for retrofit application for existing concrete or base (Bollards sold separately). 1. Drill the surface in the drilling location shown in the detailed dimensional drawings. 2. Feed the conduit through 2.45” dia hole of the Retrofit Bottom Plate. Place the Retrofit Bottom Plate on the mounting surface and tighten it with 4 screws. 3. Place Retrofit Top Plate on Retrofit Bottom Plate and tighten it with Set Screws. 4. Install Bollard on the Retrofit Top Plate using appropriate hardware.
Bollard Base
Retrofit Top Plate Set Screws Retrofit Bottom Plate Conduit
Mounting Surface
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
BOLBASE RETRO24 INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: [email protected]
base plate template
Template not to scale. Use actual plate as template. CAUTION: Before drilling and mounting, make sure to align Bollard Base Retro in the orientation that will result in the desired Bollard Fixture orientation. .257 [ 6,53 ] 8.547 [ 217,1 ]
4.500 [ 114,3 ] 45.0°
2.298 [58,37]
2.747 [69,77]
50.0°
6.500 [ 165,1 ]
