Bush Pump Above Grade Riser Pipe Replacement
Bush Pump Above Grade Riser Pipe Replacement
Bush Pump Above Grade Riser Pipe Replacement Use this guide to replace the above grade riser pipe, or remove it for repair.
Geschrieben von: Jake Devincenzi
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 1 von 9
Bush Pump Above Grade Riser Pipe Replacement
EINFÜHRUNG This guide will walk you through the procedure to remove the above grade riser pipe. You can then replace it with a new one, or perform any necessary repairs on it.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 2 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 1 — Head and Handle
Test pump performance by pumping 40 strokes.
An effective pump should return at least 10 liters. Schritt 2
Remove the two pins connecting the handle to the slider.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 3 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 3
Pull the two lever arms away from the slider.
Schritt 4
Lift the two pins attaching the pump frame to the head and handle up, off of the pump frame.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 4 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 5
Throughout this step, make sure you support the handle and head with at least three hands.
Slide the bearing rod out of the head.
Inspect the bearing rod and head for any wear or tear. Schritt 6
© iFixit — CC BY-NC-SA
de.iFixit.com
Remove the head and handle, and place them on a clean surface to prevent contamination.
Seite 5 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 7 — Riser Main Slider
Firmly lift the riser main slider with two hands.
Use caution not to drop the riser main, as this can damage the pump cylinder. Schritt 8
Use a pipe wrench to fully loosen the above grade riser pipe.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 6 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 9
Lift the slider and riser main pipe.
Place a pump rod clamp around the rod, and tighten it securely against the pump rod.
Carefully lower the riser main and slider to allow it to rest on the rod clamp.
Schritt 10
Loosen and remove both the pump rod jam nut and pump rod nut on the top of the slider.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 7 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 11
Remove the riser main slider, and inspect it for wear and tear.
Set the slider in a sanitary place to prevent contamination.
Schritt 12 — Above Grade Riser Pipe
Remove the above grade riser pipe.
Firmly screw a T-handle onto the pump rod.
If you are replacing the above ground riser main, leave the T-handle attached until you are ready to install the replacement part.
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
de.iFixit.com
Seite 8 von 9
Bush Pump Above Grade Riser Pipe Replacement Dieses Dokument wurde zuletzt angelegt am 2017-09-06 03:49:25 AM.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 9 von 9
Bush Pump Above Grade Riser Pipe Replacement Use this guide to replace the above grade riser pipe, or remove it for repair.
Geschrieben von: Jake Devincenzi
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 1 von 9
Bush Pump Above Grade Riser Pipe Replacement
EINFÜHRUNG This guide will walk you through the procedure to remove the above grade riser pipe. You can then replace it with a new one, or perform any necessary repairs on it.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 2 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 1 — Head and Handle
Test pump performance by pumping 40 strokes.
An effective pump should return at least 10 liters. Schritt 2
Remove the two pins connecting the handle to the slider.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 3 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 3
Pull the two lever arms away from the slider.
Schritt 4
Lift the two pins attaching the pump frame to the head and handle up, off of the pump frame.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 4 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 5
Throughout this step, make sure you support the handle and head with at least three hands.
Slide the bearing rod out of the head.
Inspect the bearing rod and head for any wear or tear. Schritt 6
© iFixit — CC BY-NC-SA
de.iFixit.com
Remove the head and handle, and place them on a clean surface to prevent contamination.
Seite 5 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 7 — Riser Main Slider
Firmly lift the riser main slider with two hands.
Use caution not to drop the riser main, as this can damage the pump cylinder. Schritt 8
Use a pipe wrench to fully loosen the above grade riser pipe.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 6 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 9
Lift the slider and riser main pipe.
Place a pump rod clamp around the rod, and tighten it securely against the pump rod.
Carefully lower the riser main and slider to allow it to rest on the rod clamp.
Schritt 10
Loosen and remove both the pump rod jam nut and pump rod nut on the top of the slider.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 7 von 9
Bush Pump Above Grade Riser Pipe Replacement
Schritt 11
Remove the riser main slider, and inspect it for wear and tear.
Set the slider in a sanitary place to prevent contamination.
Schritt 12 — Above Grade Riser Pipe
Remove the above grade riser pipe.
Firmly screw a T-handle onto the pump rod.
If you are replacing the above ground riser main, leave the T-handle attached until you are ready to install the replacement part.
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
de.iFixit.com
Seite 8 von 9
Bush Pump Above Grade Riser Pipe Replacement Dieses Dokument wurde zuletzt angelegt am 2017-09-06 03:49:25 AM.
© iFixit — CC BY-NC-SA
de.iFixit.com
Seite 9 von 9
