Cast Iron No-Hub Pipe & Fittings System
No-Hub Submittal S10010 - 07/11rev
Cast Iron No-Hub Pipe & Fittings System
Suggested Spec
Date
All drain, waste, vent, sewer and storm lines shall be of cast iron soil pipe, fittings and couplings, and shall be NSF Certified to conform to the CISPI 301 standard, and shall comply with ASTM A 888, latest edition. Pipe and fittings shall be marked with the collective trademarks of the Cast Iron Soil Pipe Insitute and NSF International, indicate the manufacturer’s name, country of origin, and date of manufacture, or receive prior approval of the engineer.
Project Architect Engineer Contractor
NO-HUB PIPE, 10’ LAYING LENGTH
DIMENSIONS AND TOLERANCES
Size
Wt/Piece (lbs)
Pieces/Bundle
Lbs/Bundle
Size
B Inside Diam
J Outside Diam
T Norm
T Min
1-1/2” 2 3 4 5 6 8 10 12 15
30 36 54 74 85 115 165 265 325 435
54 64 48 30 24 21 10 8 6 3
1620 2340 2592 2220 2040 2415 1740 2280 2130 1425
1-1/2” 2 3 4 5 6 8 10 12 15
1.50±.06 1.96±.09 2.96±.09 3.94±.09 4.94±.09 5.94±.09 7.94±.13 10.00±.13 11.94±.13 15.11±.13
1.90±.06 2.35±.09 3.35±.09 4.38+.09/-.05 5.30+.09/-.05 6.30+.09/-.05 8.38+.13/-.09 10.56±.09 12.50±.13 15.83±.13
.16 .16 .16 .19 .19 .19 .23 .28 .28 .35
.13 .13 .13 .15 .15 .15 .17 .22 .22 .30
Weights are approximate for shipping
T
B
J
Pipe diagram for illustration only, not to scale
For more detailed specifications of cast iron pipe and fittings, see the Cast Iron Soil Pipe Institute Pipe and Fittings Handbook, available online at www.abifoundry.com, or contact AB&I at 800-GOT-IRON (468-4766). AB&I is a founding member of CISPI.
CISPI
CERTIFIED
IAPMO
100% RECYCLED
MADE IN USA
AB&I Foundry • 7825 San Leandro Street • Oakland, CA 94621 • 800-GOT-IRON (468-4766) • www.abifoundry.com
Husky SD–4000 Submittal 4/14 rev
Super–Duty Couplings
Material Specifications
Project Architect
Engineer
Contractor
Date
Husky SD–4000 Couplings
The HUSKY SD–4000 coupling has been engineered to provide an all stainless steel coupling designed to provide superior sealing while accommodating potential dimensional disparities in the mating of cast iron no–hub pipe and fittings. This has been accomplished through the use of a super– duty corrugated shield of sufficient width to accommodate additional surface–bearing sealing clamps, torqued to 80inlbs. These additional clamps result in more uniformly rigid joint, with the load supported at both the outer edge of the coupling and the centerline of the joint. These clamps also yield increased surface–bearing contact, thereby inhibiting joint movement at higher internal pressures.
Clamps: Type 304 AISI stainless steel. 4 clamps on sizes 1-1/2"– 4', 6 clamps on sizes 5"–15" Screws: Type 305 AISI stainless steel 3/8” hex head Shield: Type 304 AISI stainless steel corrugated. Shield thickness 0.015” Gasket: Genuine neoprene as the primary elastomer, conforming to ASTM C564. Oil immersion test: 80% maximum volume change after immersion in ASTM oil No. 3 for 70 hours at 212˚F
Suggested Specification No–hub couplings shall be of the super–duty variety, with shields and bands made of 304 stainless steel, and gaskets made of genuine neoprene as the sole elastomer. 1–1/2" through 4" couplings shall have a minimum of four clamps, and 5" through 15" couplings shall have a minimum of 6 clamps. Couplings shall be installed in conformance with the manufacturer's installation instructions and local code requirements. Meets ASTM C1540, ASTM C564, FM 1680 Class 1, CSA B 602. IAMPO File No. 6726
Anaco • 1001 El Camino Avenue • 951/372–2732 • Fax: 951/738–1183
Corona, CA • 92879 • www.anaco–husky.com
anaco Standing the test of time
®
HUSKY SD–4000 SUPER– Duty Coupling Meets ASTM C 1540, ASTM C 564, FM 1680 Class 1, CSA B 602 IAPMO File No. 6726 Made in USA
Gasket Test Performance Test
Physical Tests Min. or Max. Requirements
ASTM Method
Tensile Strength
1500psi min.
D412
Elongation
250 min.
D412
Durometer (Shore A)
70 +/– 5 @ 76° +/– 5° F
D2240
Accelerated Aging
15% maximum tensile and 20% maximum elongation deterioration, 10 points maximum increase in hardness, all determinations after oven aging for 96hrs at 158°F.
D573
Compression Set
25% maximum after 22 hrs at 158°F
D395 Method B
Oil Immersion
80% maximum volume change after immersion in IRM 903 for 70hrs at 212°F
D471
Ozone Cracking
No visible cracking at 2x magnification of the gasket after 100hrs exposure in 1.5ppm ozone concentration at 100°F. Testing and inspection to be on gasket which is loop mounted to give approximately 25% elongation of outer surface.
D1149
Tear Resistance
150lbs. minimum per inch of thickness
D624
Water Obsorption
20% maximum by weight after 7 days at 158°F
D471
vv
Bracing Horizontal pipe and fittings 5” and larger must be suitably braced to prevent horizontal movement. This must be done at every branch opening or change of direction by the use of braces, blocks, rodding, or other suitable method, to prevent movement or joint separation (Ch IV, Handbook, Cast Iron Soil Pipe Institute.)
Marketed by AB&I Foundry
•
800/GOT.IRON (468–4766)
7825 San Leandro Street •
Fax: 510/632–3467
•
Oakland, CA •
•
94621
www.abifoundry.com
MUELLER FITTINGS COMPANY INC.
DECLARATION OF CONFORMANCE Mueller Fittings Co. Inc. manufactures or supplies product which are manufactured to meet the following specifications. ASME B16.22 MSS SP-104 ASME B16.29
Wrought Copper and Copper Alloy Solder Joint Pressure Fittings Wrought Copper Solder Joint Pressure Fittings Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings - DWV ASME/ANSI B16.18 Cast Copper Alloy Solder Joint Pressure Fittings ASME/ANSI B16.15 Cast Bronze Threaded Fittings ASME/ANSI B16.23 Cast Copper Alloy Solder Joint Drainage Fittings – DWV MSS SP-106 Class 150-Cast Copper Flanges shall meet the requirements of MSS SP106 and/or the workmanship and dimensional of Federal Spec. WW-F406 ASME B16.24. MSS SP – 106 Class 125 Bronze Pipe Flanges and Flanged Fittings MSS SP – 109 Welded Fabricated Copper Solder Joint Pressure Fittings MSS SP - 123
Threaded and Solder Joint Copper Unions
The materials used to manufacture these fittings are also in compliance with the following specifications. Products Made From Sheet ASTM B152 Alloy C11000 Standard Specification for Copper Sheet, Strip, Plated Rolled Bar Cast Products ASTM B584 Alloy C84400 Standard Specification for Copper Alloy Sand Castings for General Applications: Federal Specification WW-U-516 for Type III, Class A and B Copper Alloy Unions. Copper Fittings ASTM B75 Alloy C12200 or Alloy C10200
Standard Specification for Seamless Round, Copper Tube for General Engineering applications.
3400 MUELLER BRASS ROAD, COVINGTON, TN 38019 PHONE: (901) 476-5858 FAX: (901) 475-1334
Date
2/24/2015
Product Certification Mueller Copper Tube products are all manufactured in the USA. All tubing produced in Fulton, MS, and Wynne, AR, is seamless and of UNS C12200 grade of copper and is manufactured to meet the chemical and mechanical properties of the applicable ASTM specifications set forth below. When specified at order placement, Mueller Copper Tube can supply Certified Tube to meet all requirements of the current applicable ASTM specification, at an additional cost.
Streamline Copper Water Tube (Types K,L,M) ASTM B88 and ANSI/NSF 61 Streamline Copper Refrigeration Service Coils ASTM B280 Streamline Nitrogenized ACR Hard Drawn Copper Tube ASTM B280 Streamline Copper Drainage Tube (DWV) ASTM B306
*
Please contact Technical Services for certification in Oxygen and Medical service tube. (1.662.862.1700) Oxygen & Medical Service Tube To ASTM B819 (Types K & L) Hard Drawn Straight Lengths Only in Accordance To CGA Cleanness Specification; CGA G4.1 (Compressed Gas Association); & NFPA 99 (Health Care Facilities).
NSF 61 Restriction Statement: “Copper Tube (Alloy C12200) is certified by NSF to ANSI/NSF Standard 61 for public water supplies meeting or in the process of meeting the U.S. EPA Lead and Copper Rule (56FR 26460, June 7, 1991). Water supplies with pH less than 6.5 may require corrosion control to limit copper solubility in drinking water.” P. O. BOX 849 u FULTON, MS 38843 u (662) 8621700 u FAX (662) 8623002 P. O. BOX 309 u WYNNE, AR 72396 u (870) 2383201 u FAX (870) 2388724
Cast Iron No-Hub Pipe & Fittings System
Suggested Spec
Date
All drain, waste, vent, sewer and storm lines shall be of cast iron soil pipe, fittings and couplings, and shall be NSF Certified to conform to the CISPI 301 standard, and shall comply with ASTM A 888, latest edition. Pipe and fittings shall be marked with the collective trademarks of the Cast Iron Soil Pipe Insitute and NSF International, indicate the manufacturer’s name, country of origin, and date of manufacture, or receive prior approval of the engineer.
Project Architect Engineer Contractor
NO-HUB PIPE, 10’ LAYING LENGTH
DIMENSIONS AND TOLERANCES
Size
Wt/Piece (lbs)
Pieces/Bundle
Lbs/Bundle
Size
B Inside Diam
J Outside Diam
T Norm
T Min
1-1/2” 2 3 4 5 6 8 10 12 15
30 36 54 74 85 115 165 265 325 435
54 64 48 30 24 21 10 8 6 3
1620 2340 2592 2220 2040 2415 1740 2280 2130 1425
1-1/2” 2 3 4 5 6 8 10 12 15
1.50±.06 1.96±.09 2.96±.09 3.94±.09 4.94±.09 5.94±.09 7.94±.13 10.00±.13 11.94±.13 15.11±.13
1.90±.06 2.35±.09 3.35±.09 4.38+.09/-.05 5.30+.09/-.05 6.30+.09/-.05 8.38+.13/-.09 10.56±.09 12.50±.13 15.83±.13
.16 .16 .16 .19 .19 .19 .23 .28 .28 .35
.13 .13 .13 .15 .15 .15 .17 .22 .22 .30
Weights are approximate for shipping
T
B
J
Pipe diagram for illustration only, not to scale
For more detailed specifications of cast iron pipe and fittings, see the Cast Iron Soil Pipe Institute Pipe and Fittings Handbook, available online at www.abifoundry.com, or contact AB&I at 800-GOT-IRON (468-4766). AB&I is a founding member of CISPI.
CISPI
CERTIFIED
IAPMO
100% RECYCLED
MADE IN USA
AB&I Foundry • 7825 San Leandro Street • Oakland, CA 94621 • 800-GOT-IRON (468-4766) • www.abifoundry.com
Husky SD–4000 Submittal 4/14 rev
Super–Duty Couplings
Material Specifications
Project Architect
Engineer
Contractor
Date
Husky SD–4000 Couplings
The HUSKY SD–4000 coupling has been engineered to provide an all stainless steel coupling designed to provide superior sealing while accommodating potential dimensional disparities in the mating of cast iron no–hub pipe and fittings. This has been accomplished through the use of a super– duty corrugated shield of sufficient width to accommodate additional surface–bearing sealing clamps, torqued to 80inlbs. These additional clamps result in more uniformly rigid joint, with the load supported at both the outer edge of the coupling and the centerline of the joint. These clamps also yield increased surface–bearing contact, thereby inhibiting joint movement at higher internal pressures.
Clamps: Type 304 AISI stainless steel. 4 clamps on sizes 1-1/2"– 4', 6 clamps on sizes 5"–15" Screws: Type 305 AISI stainless steel 3/8” hex head Shield: Type 304 AISI stainless steel corrugated. Shield thickness 0.015” Gasket: Genuine neoprene as the primary elastomer, conforming to ASTM C564. Oil immersion test: 80% maximum volume change after immersion in ASTM oil No. 3 for 70 hours at 212˚F
Suggested Specification No–hub couplings shall be of the super–duty variety, with shields and bands made of 304 stainless steel, and gaskets made of genuine neoprene as the sole elastomer. 1–1/2" through 4" couplings shall have a minimum of four clamps, and 5" through 15" couplings shall have a minimum of 6 clamps. Couplings shall be installed in conformance with the manufacturer's installation instructions and local code requirements. Meets ASTM C1540, ASTM C564, FM 1680 Class 1, CSA B 602. IAMPO File No. 6726
Anaco • 1001 El Camino Avenue • 951/372–2732 • Fax: 951/738–1183
Corona, CA • 92879 • www.anaco–husky.com
anaco Standing the test of time
®
HUSKY SD–4000 SUPER– Duty Coupling Meets ASTM C 1540, ASTM C 564, FM 1680 Class 1, CSA B 602 IAPMO File No. 6726 Made in USA
Gasket Test Performance Test
Physical Tests Min. or Max. Requirements
ASTM Method
Tensile Strength
1500psi min.
D412
Elongation
250 min.
D412
Durometer (Shore A)
70 +/– 5 @ 76° +/– 5° F
D2240
Accelerated Aging
15% maximum tensile and 20% maximum elongation deterioration, 10 points maximum increase in hardness, all determinations after oven aging for 96hrs at 158°F.
D573
Compression Set
25% maximum after 22 hrs at 158°F
D395 Method B
Oil Immersion
80% maximum volume change after immersion in IRM 903 for 70hrs at 212°F
D471
Ozone Cracking
No visible cracking at 2x magnification of the gasket after 100hrs exposure in 1.5ppm ozone concentration at 100°F. Testing and inspection to be on gasket which is loop mounted to give approximately 25% elongation of outer surface.
D1149
Tear Resistance
150lbs. minimum per inch of thickness
D624
Water Obsorption
20% maximum by weight after 7 days at 158°F
D471
vv
Bracing Horizontal pipe and fittings 5” and larger must be suitably braced to prevent horizontal movement. This must be done at every branch opening or change of direction by the use of braces, blocks, rodding, or other suitable method, to prevent movement or joint separation (Ch IV, Handbook, Cast Iron Soil Pipe Institute.)
Marketed by AB&I Foundry
•
800/GOT.IRON (468–4766)
7825 San Leandro Street •
Fax: 510/632–3467
•
Oakland, CA •
•
94621
www.abifoundry.com
MUELLER FITTINGS COMPANY INC.
DECLARATION OF CONFORMANCE Mueller Fittings Co. Inc. manufactures or supplies product which are manufactured to meet the following specifications. ASME B16.22 MSS SP-104 ASME B16.29
Wrought Copper and Copper Alloy Solder Joint Pressure Fittings Wrought Copper Solder Joint Pressure Fittings Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings - DWV ASME/ANSI B16.18 Cast Copper Alloy Solder Joint Pressure Fittings ASME/ANSI B16.15 Cast Bronze Threaded Fittings ASME/ANSI B16.23 Cast Copper Alloy Solder Joint Drainage Fittings – DWV MSS SP-106 Class 150-Cast Copper Flanges shall meet the requirements of MSS SP106 and/or the workmanship and dimensional of Federal Spec. WW-F406 ASME B16.24. MSS SP – 106 Class 125 Bronze Pipe Flanges and Flanged Fittings MSS SP – 109 Welded Fabricated Copper Solder Joint Pressure Fittings MSS SP - 123
Threaded and Solder Joint Copper Unions
The materials used to manufacture these fittings are also in compliance with the following specifications. Products Made From Sheet ASTM B152 Alloy C11000 Standard Specification for Copper Sheet, Strip, Plated Rolled Bar Cast Products ASTM B584 Alloy C84400 Standard Specification for Copper Alloy Sand Castings for General Applications: Federal Specification WW-U-516 for Type III, Class A and B Copper Alloy Unions. Copper Fittings ASTM B75 Alloy C12200 or Alloy C10200
Standard Specification for Seamless Round, Copper Tube for General Engineering applications.
3400 MUELLER BRASS ROAD, COVINGTON, TN 38019 PHONE: (901) 476-5858 FAX: (901) 475-1334
Date
2/24/2015
Product Certification Mueller Copper Tube products are all manufactured in the USA. All tubing produced in Fulton, MS, and Wynne, AR, is seamless and of UNS C12200 grade of copper and is manufactured to meet the chemical and mechanical properties of the applicable ASTM specifications set forth below. When specified at order placement, Mueller Copper Tube can supply Certified Tube to meet all requirements of the current applicable ASTM specification, at an additional cost.
Streamline Copper Water Tube (Types K,L,M) ASTM B88 and ANSI/NSF 61 Streamline Copper Refrigeration Service Coils ASTM B280 Streamline Nitrogenized ACR Hard Drawn Copper Tube ASTM B280 Streamline Copper Drainage Tube (DWV) ASTM B306
*
Please contact Technical Services for certification in Oxygen and Medical service tube. (1.662.862.1700) Oxygen & Medical Service Tube To ASTM B819 (Types K & L) Hard Drawn Straight Lengths Only in Accordance To CGA Cleanness Specification; CGA G4.1 (Compressed Gas Association); & NFPA 99 (Health Care Facilities).
NSF 61 Restriction Statement: “Copper Tube (Alloy C12200) is certified by NSF to ANSI/NSF Standard 61 for public water supplies meeting or in the process of meeting the U.S. EPA Lead and Copper Rule (56FR 26460, June 7, 1991). Water supplies with pH less than 6.5 may require corrosion control to limit copper solubility in drinking water.” P. O. BOX 849 u FULTON, MS 38843 u (662) 8621700 u FAX (662) 8623002 P. O. BOX 309 u WYNNE, AR 72396 u (870) 2383201 u FAX (870) 2388724
