CC/CCS 29" Arm Mounted - Kim Lighting
CC/CCS 29" Arm Mounted Curvilinear Cutoff
revision 6/5/15 • kl_cc29arm_spec.pdf
Type: Job: Catalog number: /
/
Approvals:
/
Mtg. Fixture Electrical Module Finish See page 3 See page 2
/ Options See pages 4-5
Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for arm fitting.
29" Diameter Specifications 750 to 1000 Watt
29" Diameter 750 to 1000 Watt
CC
29"
DIA.
(736.6 mm)
8" (203.2 mm)
6"
11"
(152.4 mm)
(279.4 mm)
2" (50.8 mm)
CCS
Arm CrossSection
Date: Page: 1 of 5
Housing: Spun aluminum. (Rollformed linear reveals; CC: Three equally spaced reveals, K" wide, separated by K" ribs, J" deep. CCS: One J" groove, J" deep.) Sidewalls have a maximum 1° of taper, and are free of welds or fasteners. A rollformed aluminum flange is hemmed into the bottom providing support for the reflector module. An internal aluminum casting provides for mounting of the electrical module plus reinforcing for side-arm mounting of the fixture. Lens Frame Assembly: One-piece cast aluminum lens frame is attached to the housing by a zinc plated cold rolled steel hinge with a stainless steel pin. Closure is by four self-retained stainless steel screws. A stainless steel self-locking stop arm is provided to hold the lens frame in the open position while servicing. A F" thick clear flat tempered glass lens is fully gasketed by a one-piece extruded and vulcanized silicone gasket. Lens is retained in the frame by removable zinc plated steel clips. Standard Arm Mounting: Arm is one-piece extruded aluminum with internal bolt guides and fully radiussed top and bottom. Luminaire-to-pole attachment is by internal draw bolts, and includes a pole reinforcing plate with wire strain relief. Arm is circular cut to mate with specified round pole. Reflector Module: Specular Alzak® optical segments are rigidly mounted within a die-cast aluminum enclosure that attaches to the housing as a one-piece module. Reflectors are field rotatable in 90° increments. All sockets are factory prewired with a quick-disconnect plug for the ballast module. Wire penetrations to the socket are sealed by a silicone gasket to create a totally sealed optical chamber. The optical segments are positioned so that reflected light does not pass through the lamp arc tube. All HPS and PMH horizontal reflectors are equipped with a mogul base socket rated 4KV or 5KV. 750 and 1000 watt lamps utilize a lamp vibration stabilizer that braces the neck of the lamp with two-prong stainless steel clamp extending from the socket mount. Electrical Module: All electrical components are UL and CSA recognized, mounted on a single plate and factory prewired with quick-disconnect plugs. Module attaches inside the housing using keyhole slots. All ballasts are high power factor with starting temperatures of -40°F. for HPS and -20°F. for MH lamp modes. Finish/Color: Each luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) polyester powdercoat finish. Standard colors include (BL) Black, (DB) Dark Bronze, (WH) White, (PS) Platinum Silver, (SG) Stealth Gray, (LG) Light Gray, and (CC) Custom Color (Include RAL#). CAUTION: Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failute to do so may result in serious personal injury.
UL cUL 15981
Listings and Ratings CE IP66 Rated Full Cut Off2 (Flat Glass Lens Only)
25C Ambient
Suitable for wet locations Dark Sky Legislation Compliant
1 2
Kim Lighting reserves the right to change specifications without notice.
© 2015 KIM LIGHTING INC. • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
CC/CCS 29" Arm Mounted Curvilinear Cutoff
revision 6/5/15 • kl_cc29arm_spec.pdf
Type: Job:
Page: 2 of 5
Standard Features Mounting 3Y configuration is available for round poles only.
Plan View:
Wall Mount
EPA: 1.8 3.6 3.3 5.2 5.2 5.9 — Cat. No.: l 1A l 2B l 2L l 3T l 3Y l 4C l 1W Fixture Cat. No. designates CC/CCS fixture and light distribution. See the Kim Site/Roadway Optical Systems Catalog for detailed information on reflector design and application.
Horizontal Lamp CC CCS Light Distribution: Type I Type II Type III Full Cutoff Full Cutoff Full Cutoff Cat. No.:
l CC29A1
l CC29A2
l CC29A3
Type IV Forward Throw Full Cutoff
l CC29A4
Type V Square Full Cutoff
l CC29A5
l CCS29A1 l CCS29A2 l CCS29A3 l CCS29A4 l CCS29A5
© 2015 KIM LIGHTING INC. • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
CC/CCS 29" Arm Mounted Curvilinear Cutoff
revision 6/5/15 • kl_cc29arm_spec.pdf
Type: Job:
Page: 3 of 5
Standard Features Electrical Module HPS = High Pressure Sodium MH = Metal Halide PMH = Pulse Start Metal Halide
Lamp Lamp Line Watts Type Volts 750 HPS 277
Cat. Nos. for Electrical Modules available: High Pressure Sodium l 750HPS120 l 1000HPS120 l 750HPS208 l 1000HPS208 l 750HPS240 l 1000HPS240 l 750HPS277 l 1000HPS277 l 750HPS347 l 1000HPS347 l 750HPS480 l 1000HPS480
Metal Halide l 1000MH120 l 1000MH208 l 1000MH240 l 1000MH277 l 1000MH347 l 1000MH480
Lamp BT-37 Clear E-25 Clear Socket Mogul Base Mogul Base ANSI Ballast S-111 S-52 Type
BT-37 Clear Mogul Base M-47
Pulse Start Metal Halide l 750PMH120 l 1000PMH120 l 750PMH208 l 1000PMH208 l 750PMH240 l 1000PMH240 l 750PMH277 l 1000PMH277 l 750PMH347 l 1000PMH347 l 750PMH480 l 1000PMH480
NOTE: For lamp/ballast information outside of the U.S.A. and Canada, please consult your local Kim representative.
Lamp BT-37 Clear BT-37 Clear Socket Mogul Base Mogul Base ANSI Ballast M-149 M-141 Type
Finish TGIC powder coat
Color: Black Dark Bronze Cat. No.: l BL l DB
Light Gray Stealth Gray l LG
l SG
Platinum Silver White l PS
l WH
Custom Color1 l CC
Custom colors subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description: 1
© 2015 KIM LIGHTING INC. • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
CC/CCS 29" Arm Mounted Curvilinear Cutoff
revision 6/5/15 • kl_cc29arm_spec.pdf
Type: Job:
Page: 4 of 5
Optional Features Wall Mounting Cat. No. l 1W l No Option Select from Mounting on page 2.
Wall Mount: A cast mounting plate of 356 alloy, low-copper (
revision 6/5/15 • kl_cc29arm_spec.pdf
Type: Job: Catalog number: /
/
Approvals:
/
Mtg. Fixture Electrical Module Finish See page 3 See page 2
/ Options See pages 4-5
Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for arm fitting.
29" Diameter Specifications 750 to 1000 Watt
29" Diameter 750 to 1000 Watt
CC
29"
DIA.
(736.6 mm)
8" (203.2 mm)
6"
11"
(152.4 mm)
(279.4 mm)
2" (50.8 mm)
CCS
Arm CrossSection
Date: Page: 1 of 5
Housing: Spun aluminum. (Rollformed linear reveals; CC: Three equally spaced reveals, K" wide, separated by K" ribs, J" deep. CCS: One J" groove, J" deep.) Sidewalls have a maximum 1° of taper, and are free of welds or fasteners. A rollformed aluminum flange is hemmed into the bottom providing support for the reflector module. An internal aluminum casting provides for mounting of the electrical module plus reinforcing for side-arm mounting of the fixture. Lens Frame Assembly: One-piece cast aluminum lens frame is attached to the housing by a zinc plated cold rolled steel hinge with a stainless steel pin. Closure is by four self-retained stainless steel screws. A stainless steel self-locking stop arm is provided to hold the lens frame in the open position while servicing. A F" thick clear flat tempered glass lens is fully gasketed by a one-piece extruded and vulcanized silicone gasket. Lens is retained in the frame by removable zinc plated steel clips. Standard Arm Mounting: Arm is one-piece extruded aluminum with internal bolt guides and fully radiussed top and bottom. Luminaire-to-pole attachment is by internal draw bolts, and includes a pole reinforcing plate with wire strain relief. Arm is circular cut to mate with specified round pole. Reflector Module: Specular Alzak® optical segments are rigidly mounted within a die-cast aluminum enclosure that attaches to the housing as a one-piece module. Reflectors are field rotatable in 90° increments. All sockets are factory prewired with a quick-disconnect plug for the ballast module. Wire penetrations to the socket are sealed by a silicone gasket to create a totally sealed optical chamber. The optical segments are positioned so that reflected light does not pass through the lamp arc tube. All HPS and PMH horizontal reflectors are equipped with a mogul base socket rated 4KV or 5KV. 750 and 1000 watt lamps utilize a lamp vibration stabilizer that braces the neck of the lamp with two-prong stainless steel clamp extending from the socket mount. Electrical Module: All electrical components are UL and CSA recognized, mounted on a single plate and factory prewired with quick-disconnect plugs. Module attaches inside the housing using keyhole slots. All ballasts are high power factor with starting temperatures of -40°F. for HPS and -20°F. for MH lamp modes. Finish/Color: Each luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) polyester powdercoat finish. Standard colors include (BL) Black, (DB) Dark Bronze, (WH) White, (PS) Platinum Silver, (SG) Stealth Gray, (LG) Light Gray, and (CC) Custom Color (Include RAL#). CAUTION: Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failute to do so may result in serious personal injury.
UL cUL 15981
Listings and Ratings CE IP66 Rated Full Cut Off2 (Flat Glass Lens Only)
25C Ambient
Suitable for wet locations Dark Sky Legislation Compliant
1 2
Kim Lighting reserves the right to change specifications without notice.
© 2015 KIM LIGHTING INC. • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
CC/CCS 29" Arm Mounted Curvilinear Cutoff
revision 6/5/15 • kl_cc29arm_spec.pdf
Type: Job:
Page: 2 of 5
Standard Features Mounting 3Y configuration is available for round poles only.
Plan View:
Wall Mount
EPA: 1.8 3.6 3.3 5.2 5.2 5.9 — Cat. No.: l 1A l 2B l 2L l 3T l 3Y l 4C l 1W Fixture Cat. No. designates CC/CCS fixture and light distribution. See the Kim Site/Roadway Optical Systems Catalog for detailed information on reflector design and application.
Horizontal Lamp CC CCS Light Distribution: Type I Type II Type III Full Cutoff Full Cutoff Full Cutoff Cat. No.:
l CC29A1
l CC29A2
l CC29A3
Type IV Forward Throw Full Cutoff
l CC29A4
Type V Square Full Cutoff
l CC29A5
l CCS29A1 l CCS29A2 l CCS29A3 l CCS29A4 l CCS29A5
© 2015 KIM LIGHTING INC. • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
CC/CCS 29" Arm Mounted Curvilinear Cutoff
revision 6/5/15 • kl_cc29arm_spec.pdf
Type: Job:
Page: 3 of 5
Standard Features Electrical Module HPS = High Pressure Sodium MH = Metal Halide PMH = Pulse Start Metal Halide
Lamp Lamp Line Watts Type Volts 750 HPS 277
Cat. Nos. for Electrical Modules available: High Pressure Sodium l 750HPS120 l 1000HPS120 l 750HPS208 l 1000HPS208 l 750HPS240 l 1000HPS240 l 750HPS277 l 1000HPS277 l 750HPS347 l 1000HPS347 l 750HPS480 l 1000HPS480
Metal Halide l 1000MH120 l 1000MH208 l 1000MH240 l 1000MH277 l 1000MH347 l 1000MH480
Lamp BT-37 Clear E-25 Clear Socket Mogul Base Mogul Base ANSI Ballast S-111 S-52 Type
BT-37 Clear Mogul Base M-47
Pulse Start Metal Halide l 750PMH120 l 1000PMH120 l 750PMH208 l 1000PMH208 l 750PMH240 l 1000PMH240 l 750PMH277 l 1000PMH277 l 750PMH347 l 1000PMH347 l 750PMH480 l 1000PMH480
NOTE: For lamp/ballast information outside of the U.S.A. and Canada, please consult your local Kim representative.
Lamp BT-37 Clear BT-37 Clear Socket Mogul Base Mogul Base ANSI Ballast M-149 M-141 Type
Finish TGIC powder coat
Color: Black Dark Bronze Cat. No.: l BL l DB
Light Gray Stealth Gray l LG
l SG
Platinum Silver White l PS
l WH
Custom Color1 l CC
Custom colors subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description: 1
© 2015 KIM LIGHTING INC. • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
CC/CCS 29" Arm Mounted Curvilinear Cutoff
revision 6/5/15 • kl_cc29arm_spec.pdf
Type: Job:
Page: 4 of 5
Optional Features Wall Mounting Cat. No. l 1W l No Option Select from Mounting on page 2.
Wall Mount: A cast mounting plate of 356 alloy, low-copper (
