C:\Documents and Settings\S5592 - Sensio
Instruction for the use of the LED POWER SUPPLY With terminal cover and cable clamp, the LED power supply can
Model: SE40625
be independent installed.
Applications This type of power supply is an exclusively designed stabilized power supply for LED lamp. With constant current constant
·The indicated load should not be exceeded. For 3W high power LED(IF=700mA, VF=3.6V), 1 to 2PCS.
voltage (CCCV) technology, it is suitable for constant voltage
·The maximum length of the output cable to the LED lamps
lamps(12VDC) connected in parallel or constant current
should not exceed 2m in order to meet the EMC standard.
lamps(700mA) connected in series. As an advantage of CCCV the LED power supply is used for purposes other than
technology, a switch can be installed between secondary side
·If
and lamps.
originally
intended
or
it
is
connected
incorrectly,
the
manufacturer is not responsible for possible damages. The built-in protection circuit will shut down the power supply in case of such faults as: open circuit, short circuit , over load or over temperature. The power supply will restart automatically after fault correction.
Important information for the installation · The unit uses dangerous mains voltage(100~240VAC), it should only be installed by qualified electricians according to European safety standards or relevant nation regulations. Failure to observe any of the installation instructions may cause fire or other hazards.
Specifications Input voltage : 100~240VAC Input frequency : 50/60Hz Input current : max.0.16A Input power factor : 0.4C Constant output curren : 700mA Output voltage : 3~8.4VDC(CC) or 12VDC(CV) Rated output power : 1~6 W LED type : high power LED 3W x1 to2 Ambient temperature : -20-40℃ Case temperature : 70℃ IP protection : IP20 2 Primary cable : H03VVH2-F 2X0.75mm or SPT-2 18AWG 2 Secondary cable : H03VVH2-F 2X0.75mm or SPT-2 18AWG
SE40625
www.sensio.co.uk
Model: SE40625
be independent installed.
Applications This type of power supply is an exclusively designed stabilized power supply for LED lamp. With constant current constant
·The indicated load should not be exceeded. For 3W high power LED(IF=700mA, VF=3.6V), 1 to 2PCS.
voltage (CCCV) technology, it is suitable for constant voltage
·The maximum length of the output cable to the LED lamps
lamps(12VDC) connected in parallel or constant current
should not exceed 2m in order to meet the EMC standard.
lamps(700mA) connected in series. As an advantage of CCCV the LED power supply is used for purposes other than
technology, a switch can be installed between secondary side
·If
and lamps.
originally
intended
or
it
is
connected
incorrectly,
the
manufacturer is not responsible for possible damages. The built-in protection circuit will shut down the power supply in case of such faults as: open circuit, short circuit , over load or over temperature. The power supply will restart automatically after fault correction.
Important information for the installation · The unit uses dangerous mains voltage(100~240VAC), it should only be installed by qualified electricians according to European safety standards or relevant nation regulations. Failure to observe any of the installation instructions may cause fire or other hazards.
Specifications Input voltage : 100~240VAC Input frequency : 50/60Hz Input current : max.0.16A Input power factor : 0.4C Constant output curren : 700mA Output voltage : 3~8.4VDC(CC) or 12VDC(CV) Rated output power : 1~6 W LED type : high power LED 3W x1 to2 Ambient temperature : -20-40℃ Case temperature : 70℃ IP protection : IP20 2 Primary cable : H03VVH2-F 2X0.75mm or SPT-2 18AWG 2 Secondary cable : H03VVH2-F 2X0.75mm or SPT-2 18AWG
SE40625
www.sensio.co.uk
