Compaq Presario v2000 Display Panel Replacement
Compaq Presario v2000 Display Panel Replacement
Compaq Presario v2000 Display Panel Replacement How to remove and replace the LCD display panel
Written By: Andrew
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Compaq Presario v2000 Display Panel Replacement
INTRODUCTION How to remove and replace the LCD display panel
TOOLS: Phillips #1 Screwdriver (1) Spudger (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Compaq Presario v2000 Display Panel Replacement
Step 1 — Display Panel
Remove the battery before starting working on the laptop
Step 2
There are 6 screws holding on the display bezel, hidden behind screw covers
Remove the screw covers with a spudger or small flat blade screwdriver
Remove the screws with a phillips #1 screwdriver
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Compaq Presario v2000 Display Panel Replacement
Step 3
Use your fingers to pry off the bezel at the top and sides first
Don't use anything hard and sharp as you may damage the panel
You may need to use a spudger or flat blade screwdriver at the bottom edge around the hinges
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the backlight inverter cable using a spudger or flat blade screwdriver
Page 4 of 6
Compaq Presario v2000 Display Panel Replacement
Step 5
Remove the two side screws at the top of the panel first
Then remove the two side screws at the bottom. It may be necessary to angle the display away from the back cover to reach these well
Hold on to the display when removing the last screw, there is still a cable on the back to remove Step 6
Lay the panel down on the keyboard
Remove the tape covering the display cable connecter
Remove the display cable from the panel
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Compaq Presario v2000 Display Panel Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-24 02:14:16 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
Compaq Presario v2000 Display Panel Replacement How to remove and replace the LCD display panel
Written By: Andrew
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Compaq Presario v2000 Display Panel Replacement
INTRODUCTION How to remove and replace the LCD display panel
TOOLS: Phillips #1 Screwdriver (1) Spudger (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Compaq Presario v2000 Display Panel Replacement
Step 1 — Display Panel
Remove the battery before starting working on the laptop
Step 2
There are 6 screws holding on the display bezel, hidden behind screw covers
Remove the screw covers with a spudger or small flat blade screwdriver
Remove the screws with a phillips #1 screwdriver
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Compaq Presario v2000 Display Panel Replacement
Step 3
Use your fingers to pry off the bezel at the top and sides first
Don't use anything hard and sharp as you may damage the panel
You may need to use a spudger or flat blade screwdriver at the bottom edge around the hinges
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the backlight inverter cable using a spudger or flat blade screwdriver
Page 4 of 6
Compaq Presario v2000 Display Panel Replacement
Step 5
Remove the two side screws at the top of the panel first
Then remove the two side screws at the bottom. It may be necessary to angle the display away from the back cover to reach these well
Hold on to the display when removing the last screw, there is still a cable on the back to remove Step 6
Lay the panel down on the keyboard
Remove the tape covering the display cable connecter
Remove the display cable from the panel
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Compaq Presario v2000 Display Panel Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-24 02:14:16 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
