DANGER WARNING Martin® Return Roller Basket ... AWS
Martin® Return Roller Basket Installation Instructions
!
DANGER
Before installing, servicing, or adjusting the conveyor equipment, turn off and lock out/tag out all energy sources to the conveyor and conveyor accessories according to ANSI standards. Failure to do so could result in serious injury or death. !
WARNING
®
Martin Return Roller Baskets are designed to prevent return roller from falling in case of mechanical failure. Martin® Return Roller Baskets do not guard personnel from contacting return roller. 13.25 (337) Bolt Centers
13.25 (337) Bolt Centers
Return Roller Centerline
Return Roller Centerline 1.81 (46)
6.625 (168)
6.625 (168)
12.64 (321)
1.81 (46)
6.625 (168)
6.625 (168)
12.64 (321)
Outside of Stringer Mount Brackets
Bottom of Stringer Mount Brackets
Figure 1. Martin® Return Roller Basket Mounting Location 1. Turn off and lock out/tag out energy source according to ANSI standards. 2. Mark vertical center line of return roller. Make sure center line is perpendicular to belt line. 3. Measure 6.625 in. (168 mm) in both directions and mark locations.
D
D E
B
B
E A
A
C
C
A. Cap Screw, Washers, and Lock Nut B. Mount Brackets C. End Plate D. Stringer E. Cap Screw, Washers, and Nut
Figure 2. Martin® Return Roller Basket Installation 4. Determine which mounting brackets are best suited for the application. 5. Install mounting brackets (B) on end plate (C) using cap screws, washers and lock nuts (A). 6. Align mount brackets with locations marked in step 3. 7. Using the brackets as a template, mark location of mounting holes. 8. Drill or cut holes in stringer (D). Remove burrs and sharp edges. 9. Install end plate with brackets to stringer using cap screws, washers, and nuts (E). 10. Repeat steps 2–9 on opposite side of conveyor.
J
I K
H
L F. Side Panel G. Cap Screw with Shoulder H. Nylon Spacer I. Washer
G
F
J. Lock Nut K. Lock Pin L. Cap Screw, Washers, and Nut
Figure 3. Martin® Return Roller Basket Installation
NOTE It may be necessary to loosen cap screws and nuts (L) to allow side panel to fit properly between end plates. 11. Install side panel (F) onto end plate using cap screw (G), nylon spacer (H), washer (I), and lock nut (J). Nylon spacer must be installed between the end plate and side panel. 12. Repeat step 11 on opposite end of panel. 13. Rotate side panel up into the closed position and insert lock pins (K) on both ends of side panel. 14. Repeat steps 11–13 to install other side panel. 15. Make sure all fasteners are tight and return roller baskets do not interfere with operation of conveyor.
Part Numbers RRB–XX X X
NOMENCLATURE P/N Prefix Belt Width (inches) Stringer Color/Material
STRINGER S: Standard Base W: Wide Base
COLOR/MATERIAL O: Martin® Orange C: 304 Stainless Steel S: 316 Stainless Steel
Form No. M3840-06/12 © 2011, 2012 MARTIN ENGINEERING COMPANY. All rights reserved. Patents and patents pending, ® Registered trademark of Martin Engineering Company in the U.S. and other select locations.
One Martin Place Neponset, IL 61345-9766 USA Phone: 309-852-2384 or 800-544-2947 FAX: 800-814-1553 www.martin-eng.com
!
DANGER
Before installing, servicing, or adjusting the conveyor equipment, turn off and lock out/tag out all energy sources to the conveyor and conveyor accessories according to ANSI standards. Failure to do so could result in serious injury or death. !
WARNING
®
Martin Return Roller Baskets are designed to prevent return roller from falling in case of mechanical failure. Martin® Return Roller Baskets do not guard personnel from contacting return roller. 13.25 (337) Bolt Centers
13.25 (337) Bolt Centers
Return Roller Centerline
Return Roller Centerline 1.81 (46)
6.625 (168)
6.625 (168)
12.64 (321)
1.81 (46)
6.625 (168)
6.625 (168)
12.64 (321)
Outside of Stringer Mount Brackets
Bottom of Stringer Mount Brackets
Figure 1. Martin® Return Roller Basket Mounting Location 1. Turn off and lock out/tag out energy source according to ANSI standards. 2. Mark vertical center line of return roller. Make sure center line is perpendicular to belt line. 3. Measure 6.625 in. (168 mm) in both directions and mark locations.
D
D E
B
B
E A
A
C
C
A. Cap Screw, Washers, and Lock Nut B. Mount Brackets C. End Plate D. Stringer E. Cap Screw, Washers, and Nut
Figure 2. Martin® Return Roller Basket Installation 4. Determine which mounting brackets are best suited for the application. 5. Install mounting brackets (B) on end plate (C) using cap screws, washers and lock nuts (A). 6. Align mount brackets with locations marked in step 3. 7. Using the brackets as a template, mark location of mounting holes. 8. Drill or cut holes in stringer (D). Remove burrs and sharp edges. 9. Install end plate with brackets to stringer using cap screws, washers, and nuts (E). 10. Repeat steps 2–9 on opposite side of conveyor.
J
I K
H
L F. Side Panel G. Cap Screw with Shoulder H. Nylon Spacer I. Washer
G
F
J. Lock Nut K. Lock Pin L. Cap Screw, Washers, and Nut
Figure 3. Martin® Return Roller Basket Installation
NOTE It may be necessary to loosen cap screws and nuts (L) to allow side panel to fit properly between end plates. 11. Install side panel (F) onto end plate using cap screw (G), nylon spacer (H), washer (I), and lock nut (J). Nylon spacer must be installed between the end plate and side panel. 12. Repeat step 11 on opposite end of panel. 13. Rotate side panel up into the closed position and insert lock pins (K) on both ends of side panel. 14. Repeat steps 11–13 to install other side panel. 15. Make sure all fasteners are tight and return roller baskets do not interfere with operation of conveyor.
Part Numbers RRB–XX X X
NOMENCLATURE P/N Prefix Belt Width (inches) Stringer Color/Material
STRINGER S: Standard Base W: Wide Base
COLOR/MATERIAL O: Martin® Orange C: 304 Stainless Steel S: 316 Stainless Steel
Form No. M3840-06/12 © 2011, 2012 MARTIN ENGINEERING COMPANY. All rights reserved. Patents and patents pending, ® Registered trademark of Martin Engineering Company in the U.S. and other select locations.
One Martin Place Neponset, IL 61345-9766 USA Phone: 309-852-2384 or 800-544-2947 FAX: 800-814-1553 www.martin-eng.com
