Disassembling Pentax K200D Front Cover
Disassembling Pentax K200D Front Cover
Disassembling Pentax K200D Front Cover Remove the front cover to access the lens mount, manual and autofocus switch, lens release switch, timer light, and other components.
Written By: Rick Nelson
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 4
Disassembling Pentax K200D Front Cover
INTRODUCTION Remove the front cover to access the lens mount, manual and autofocus switch, lens release switch, timer light, and other components.
TOOLS: Phillips #00 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 4
Disassembling Pentax K200D Front Cover
Step 1 — Preparation
Retrieve your Pentax K200D, the lens mount cover, and required tools.
Remove the lens, if you have one attached, and replace it with the lens mount cover to make handling and repair easier.
With the camera turned on, press the pop-up flash button to release the flash.
Step 2 — Flash
Be sure to turn the camera back off before proceeding.
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the two 4.3 mm Phillips screws securing the top edge of the front cover to the top cover.
Page 3 of 4
Disassembling Pentax K200D Front Cover
Step 3 — Bottom cover
Remove the seven 4.3 mm Phillips screws securing the bottom cover to the camera body
Remove the two 2.5 mm Phillips screws also securing the bottom cover to the camera body
Open the battery door and carefully remove the bottom cover, as the battery door components become unsecured when the bottom cover is removed.
Step 4
Remove the two 4.3 mm Phillips screws securing the right side of the front cover to the camera body.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-22 12:50:15 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 4
Disassembling Pentax K200D Front Cover Remove the front cover to access the lens mount, manual and autofocus switch, lens release switch, timer light, and other components.
Written By: Rick Nelson
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 4
Disassembling Pentax K200D Front Cover
INTRODUCTION Remove the front cover to access the lens mount, manual and autofocus switch, lens release switch, timer light, and other components.
TOOLS: Phillips #00 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 4
Disassembling Pentax K200D Front Cover
Step 1 — Preparation
Retrieve your Pentax K200D, the lens mount cover, and required tools.
Remove the lens, if you have one attached, and replace it with the lens mount cover to make handling and repair easier.
With the camera turned on, press the pop-up flash button to release the flash.
Step 2 — Flash
Be sure to turn the camera back off before proceeding.
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the two 4.3 mm Phillips screws securing the top edge of the front cover to the top cover.
Page 3 of 4
Disassembling Pentax K200D Front Cover
Step 3 — Bottom cover
Remove the seven 4.3 mm Phillips screws securing the bottom cover to the camera body
Remove the two 2.5 mm Phillips screws also securing the bottom cover to the camera body
Open the battery door and carefully remove the bottom cover, as the battery door components become unsecured when the bottom cover is removed.
Step 4
Remove the two 4.3 mm Phillips screws securing the right side of the front cover to the camera body.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-22 12:50:15 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 4
