Disassembling VTech MobiGo Touch Learning System Screen ...
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Disassembling VTech MobiGo Touch Learning System Screen Enclosure Disassemble the screen enclosure of the VTech MobiGo Touch Learning System.
Written By: Daniel Kresge
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
INTRODUCTION The VTech has two cases. The main case housing the main circuit board and other components and a smaller enclosure that houses the screen and two buttons. This guide is how to disassemble the Vtech to gain access to the screen and button components.
TOOLS: Screwdriver (1) iFixit Opening Tools (1) Magnetic Project Mat (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Step 1 — Case
Remove the battery covers and the four batteries.
Step 2
Remove the four plastic caps with a metal spudger to expose the 6.0 mm Philips JIS #0 case screws.
Remove the eight 6.0 mm JIS #0 case screws.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Step 3
Using a plastic opening tool, separate the two pieces of the case carefully.
Step 4 — Disassembling VTech MobiGo Touch Learning System Screen Enclosure
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the three 4.0 mm Philips J0 screws holding the "L" shaped brackets in place.
Page 4 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Step 5
Remove the three "L" shaped brackets and the spring.
Flip the device over and remove the three 4.0 mm Philips J0 case screws.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Step 7
Separate the front and back of the case.
Use a plastic opening tool if necessary.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-25 01:28:12 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure Disassemble the screen enclosure of the VTech MobiGo Touch Learning System.
Written By: Daniel Kresge
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
INTRODUCTION The VTech has two cases. The main case housing the main circuit board and other components and a smaller enclosure that houses the screen and two buttons. This guide is how to disassemble the Vtech to gain access to the screen and button components.
TOOLS: Screwdriver (1) iFixit Opening Tools (1) Magnetic Project Mat (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Step 1 — Case
Remove the battery covers and the four batteries.
Step 2
Remove the four plastic caps with a metal spudger to expose the 6.0 mm Philips JIS #0 case screws.
Remove the eight 6.0 mm JIS #0 case screws.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Step 3
Using a plastic opening tool, separate the two pieces of the case carefully.
Step 4 — Disassembling VTech MobiGo Touch Learning System Screen Enclosure
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the three 4.0 mm Philips J0 screws holding the "L" shaped brackets in place.
Page 4 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Step 5
Remove the three "L" shaped brackets and the spring.
Flip the device over and remove the three 4.0 mm Philips J0 case screws.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Disassembling VTech MobiGo Touch Learning System Screen Enclosure
Step 7
Separate the front and back of the case.
Use a plastic opening tool if necessary.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-25 01:28:12 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
