Double Wedding Ring Table Runner
1
Double Wedding Ring Table Runner Finished Size 17½” x 46” Copyright © 2014 HoopSisters
This table runner is made with 5 inch blocks and one single piece of fabric as the rings, unlike the Double Wedding Ring quilt, which is made from striped pieced fabrics done before making the block.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
2
Double Wedding Ring Table Runner Finished Size 17½” x 46” Copyright © 2014 HoopSisters
Fabric Requirements:
Supplies:
Background: 1 1/4 yards
Battilizer® - 5 yard package
Backing: 1 yard
Trimmer By George 2.0®
Ring Fabric: 3/4 yard
HoopScissors Mini
Binding: 1/3 yard
VanishLite Water Soluble Thread
Embroidery threads to match your background and ring fabrics
Cutting Chart Background Fabric
Cut 16
7½” x 7½”
Cut 20
7½” x 6”
Cut 4
6” x 6”
Cut 16
6” x 6”
Cut 20
6” x 5”
Cut 4
4½ x 4½
Ring Fabric
Cut 16
6” x 6”
Binding Fabric
Cut 4
2½ x Width of Fabric
Backing Fabric
3
Main Double Wedding Ring Block - Stitch 16 for Runner in 5 inch size Copyright © 2014 HoopSisters 1.) Hoop Battilizer®. Place neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer®
2.) Place water soluble thread in the needle only. Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew outline and placement stitches.
3.) Place Thread A in the needle and bobbin and stitch embroidery. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
4.) Still using Thread A in the needle and bobbin, Place Ring Fabric, centering over placement stitches. Sew tack down. Cut small slit (see X). Trim up to stitching inside and outside rings. Keep center section for Border blocks.
5.) Place Thread B in the needle and bobbin and stitch the quilting and deco stitch.
6.) Place Thread A in the needle and bobbin and stitch satin stitches.
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
7.) Place Thread B in the needle and bobbin and stitch quilting.
8.) Place water soluble thread in the needle and neutral embroidery thread in the bobbin and stitch basting stitch.
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
x
4
Main Double Wedding Ring Block Block Trimming Instructions Copyright © 2014 HoopSisters
Trim the backing and Battilizer® up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4” from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
5
Double Wedding Ring Border Blocks - Stitch 10 Block A, and 10 Block B for Runner in 5 inch size Copyright © 2014 HoopSisters 2.) Place water soluble thread in the needle only.
1.) Hoop Battilizer®. Place the neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer®
Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew outline and placement stitches.
4.) Place Thread B in the needle and bobbin and stitch the quilting and deco stitch.
3.) Place fabric from center of main block over placement stitches. Sew tack down stitches.
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
Trim close to stitching.
5.) Place Thread A in the needle and bobbin and stitch satin stitches. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
7.) Place Thread A in the needle and bobbin and stitch embroidery. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
A
B
6.) Place Thread B in the needle and bobbin and stitch quilting.
A
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
B
8.) Place water soluble thread in the needle and neutral embroidery thread in the bobbin and stitch basting stitch. This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
6
Double Wedding Ring Border Blocks Copyright © 2014 HoopSisters Double Wedding Ring Border Block Block Trimming Instructions Cut the side marked in red that will have binding attached to it 1/4” through all layers. For the other three sides, trim the backing and Battilizer® up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4” from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow.
A
B
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
7
Double Wedding Ring Corner Block - Stitch 4 for Runner in 5 inch size Copyright © 2014 HoopSisters 1.) Hoop Battilizer®. Place the neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer®
3.) Place Thread B in the needle and bobbin and stitch quilting. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
2.) Place Water soluble thread in the needle only. Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew basting stitch.
4.) Place Water soluble thread in the needle and embroidery bobbin thread in the bobbin and stitch basting stitch. This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block.
Double Wedding Ring Corner Block Block Trimming Instructions Cut the two sides marked in red that will have binding attached to it 1/4” through all layers. For the remaining two sides, trim the backing and Battilizer® up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4” from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
Double Wedding Ring Table Runner Finished Size 17½” x 46” Copyright © 2014 HoopSisters
This table runner is made with 5 inch blocks and one single piece of fabric as the rings, unlike the Double Wedding Ring quilt, which is made from striped pieced fabrics done before making the block.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
2
Double Wedding Ring Table Runner Finished Size 17½” x 46” Copyright © 2014 HoopSisters
Fabric Requirements:
Supplies:
Background: 1 1/4 yards
Battilizer® - 5 yard package
Backing: 1 yard
Trimmer By George 2.0®
Ring Fabric: 3/4 yard
HoopScissors Mini
Binding: 1/3 yard
VanishLite Water Soluble Thread
Embroidery threads to match your background and ring fabrics
Cutting Chart Background Fabric
Cut 16
7½” x 7½”
Cut 20
7½” x 6”
Cut 4
6” x 6”
Cut 16
6” x 6”
Cut 20
6” x 5”
Cut 4
4½ x 4½
Ring Fabric
Cut 16
6” x 6”
Binding Fabric
Cut 4
2½ x Width of Fabric
Backing Fabric
3
Main Double Wedding Ring Block - Stitch 16 for Runner in 5 inch size Copyright © 2014 HoopSisters 1.) Hoop Battilizer®. Place neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer®
2.) Place water soluble thread in the needle only. Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew outline and placement stitches.
3.) Place Thread A in the needle and bobbin and stitch embroidery. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
4.) Still using Thread A in the needle and bobbin, Place Ring Fabric, centering over placement stitches. Sew tack down. Cut small slit (see X). Trim up to stitching inside and outside rings. Keep center section for Border blocks.
5.) Place Thread B in the needle and bobbin and stitch the quilting and deco stitch.
6.) Place Thread A in the needle and bobbin and stitch satin stitches.
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
7.) Place Thread B in the needle and bobbin and stitch quilting.
8.) Place water soluble thread in the needle and neutral embroidery thread in the bobbin and stitch basting stitch.
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
x
4
Main Double Wedding Ring Block Block Trimming Instructions Copyright © 2014 HoopSisters
Trim the backing and Battilizer® up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4” from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
5
Double Wedding Ring Border Blocks - Stitch 10 Block A, and 10 Block B for Runner in 5 inch size Copyright © 2014 HoopSisters 2.) Place water soluble thread in the needle only.
1.) Hoop Battilizer®. Place the neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer®
Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew outline and placement stitches.
4.) Place Thread B in the needle and bobbin and stitch the quilting and deco stitch.
3.) Place fabric from center of main block over placement stitches. Sew tack down stitches.
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
Trim close to stitching.
5.) Place Thread A in the needle and bobbin and stitch satin stitches. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
7.) Place Thread A in the needle and bobbin and stitch embroidery. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
A
B
6.) Place Thread B in the needle and bobbin and stitch quilting.
A
NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
B
8.) Place water soluble thread in the needle and neutral embroidery thread in the bobbin and stitch basting stitch. This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
6
Double Wedding Ring Border Blocks Copyright © 2014 HoopSisters Double Wedding Ring Border Block Block Trimming Instructions Cut the side marked in red that will have binding attached to it 1/4” through all layers. For the other three sides, trim the backing and Battilizer® up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4” from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow.
A
B
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
7
Double Wedding Ring Corner Block - Stitch 4 for Runner in 5 inch size Copyright © 2014 HoopSisters 1.) Hoop Battilizer®. Place the neutral embroidery thread in the needle and embroidery bobbin thread in the bobbin and sew the pattern onto the Battilizer®
3.) Place Thread B in the needle and bobbin and stitch quilting. NOTE: Make sure to do a needle down, needle up to bring your bobbin thread to the top before stitching the embroidery.
2.) Place Water soluble thread in the needle only. Place Backing Fabric 2 on the back of the hoop. Place Background Fabric 1 on the top of the hoop. Sew basting stitch.
4.) Place Water soluble thread in the needle and embroidery bobbin thread in the bobbin and stitch basting stitch. This is the stitching you will put the edge of the Trimmer By George 2.0 against to trim block.
Double Wedding Ring Corner Block Block Trimming Instructions Cut the two sides marked in red that will have binding attached to it 1/4” through all layers. For the remaining two sides, trim the backing and Battilizer® up to the basting stitch using the Trimmer By George 2.0. Cut fabric on front of block 3/4” from the basting stitch. You will use the no sash method for joining the blocks. See Joining Slideshow.
Photocopying, digitizing, and all other copying to “share” these instructions is strictly prohibited by law. Thank you for respecting the designer’s copyright.
