Electronic Pricer Kit 1
06.08.15 Page 1/10 Item # 10027
Electronic Pricer Kit Contents:
Instru ctions
CARTON
Securing Clips (2)
(2) Transformer (2) 8 1/4" Adapter (6) Message Set (2) Block-Out (12) Pieces Total) Panel
Securing Tape Set of (3) (2) #10-32 (4) #6-32 (2) Cable Ties (2) Electronic Pricer x 1 1/4” x 5/8” Screws Screws NOTE: May contain extra hardware not required.
(1) Storage Pocket w/ Instruction Card
Block Out Decals Set of (3)
Cover Up Decals Set of (9)
1. Determine location of Electronic Pricers.
(or)
Flip-Up Lighted Sign - 5 1/2" Instruction #'s 2-9
Header Lighted Sign - 8 1/4" Instruction #'s 10-21
The Electronic Pricers can be mounted to Flip Signs or Header Signs. This kit contains the required components to mount (2) Pricers. The instruction sheet first covers installation of the pricer onto a Flip Sign, then onto a Header Sign, and then general information.
Instruction Sheet Part # 200261
06.08.15 Page 2/10 Item # 10027
Electronic Pricer Kit
2.
Installation of Pricer onto a Flip Sign.
Remove (2) screws holding right side end cap on.
WARNING: This step must be done or damage to the power cord may occur.
3.
Feed the Transformer cord thru the coiled power cord and thru the (2) ball chain loops of the Flip Sign. Transformer Plug
Ball Chains
Side View Flip Sign
Instruction Sheet Part # 200261
06.08.15 Page 3/10 Item # 10027
Electronic Pricer Kit
4.
Remove the full length clear graphic cover, it is not used with the pricer.
5.
Slide the acrylic diffuser out the end of the sign a couple of inches. Wrap a Block-Out Decal around the far right edge. Make sure the decal is along the edge of the diffuser. Slide the diffuser back into the sign.
Acrylic Diffuser
Block-out Decal
Instruction Sheet Part # 200261
06.08.15 Page 4/10 Item # 10027
Electronic Pricer Kit
6.
7.
Plug Transformer power cord into pricer and route cord out the side.
Start to slide the Blockout Panel into the sign channel (rubber pads touching the acrylic diffuser). When it is halfway in, start sliding the pricer into the sign channel as well. Continue sliding both pieces in together until the pricer is flush with Clear Graphic Cover the edge of the sign.
Block-out Panel (Rubber pads towards sign) Electronic Pricer
Note: The left edge of the Block-out Panel should always be sticking out from behind the left side of the pricer. Leave about an inch of the Blockout Panel exposed to the left side of the pricer. You will need to slide it behind the clear graphic cover.
8. 9.
Replace end cap. Apply (1) piece of black securing tape to the bottom of the Flip-up Sign and Electronic Pricer to keep Bottom of pricer from sliding left / Flip-up Sign right. PRESS FIRMLY.
Black Securing Tape Instruction Sheet Part # 200261
06.08.15 Page 5/10 Item # 10027
Electronic Pricer Kit Front view of installed electronic pricer
Edge of Narrow Clear Graphic Cover
Electronic Pricer
Block-out decal behind Pricer
Edge of Block-out Panel
WARNING: Failure to perform this step could result in the Pricer power cord becoming damaged.
10.
A Attach (1) securing clip to the right hand end cap of the Flip Up Lighted Sign with the opening “up” (as shown). B Attach (1) securing clip to the back of the Flip Up Lighted Sign with the opening “down” (as shown). C Press firmly to ensure the clips do not come off. 10. A
11.
10. B Cable tie Pricer power cord to Flip Sign power cord.
Secure Pricer power cord.
Electronic Pricer Securing Clips
Flip Sign power cord
Straighten and route cord along side of end cap and along back to Flip Sign power cord. Tuck Pricer power cord into securing clips. Cable tie to Flip Sign power cord. WARNING: Do not over tighten cable tie. This could damage power cord insulation WARNING: Raise and release the Flip Sign, looking carefully at the power cords to ensure there is no binding or pinching. Instruction Sheet Part # 200261
06.08.15 Page 6/10 Item # 10027
Electronic Pricer Kit
12. Install and adjust #10 x 32 x 1 1/4" black machine screws in both hinges. All signs should be adjusted to the same viewing angle.
Electronic Pricer
Adjustment Screw
Approx 5O Facing Up
13.
Note: 2' Flip signs on 2' OTP fixtures do not get pricers attached to them. The signs without pricers will naturally face upward approximately 5o, signs with pricers will naturally face downward slightly. Adjust the screws on the flip signs with pricers so that they also face upward approximately 5o.
Installation of Pricer onto a Header Sign.
Remove clear graphic cover by lifting at finger notch and pulling slightly forward and down.
Narrow Graphic Cover
Do the same with the narrow graphic cover.
Full Length Clear Graphic Cover
Finger Notch
WARNING: Unplug and turn off power before Step #11
14.
Remove Acrylic Diffuser by lifting, then pulling slightly forward and down.
Acrylic Diffuser
Instruction Sheet Part # 200261
06.08.15 Page 7/10 Item # 10027
Electronic Pricer Kit
15.
Place a black Block-out Decal along the edge of the right side of the Acrylic Diffuser.
Acrylic Diffuser
17.
16.
Reinstall the Acrylic Diffuser.
Block-out Decal
Acrylic Diffuser
Reinstall the Tobacco Representative Instruction Packet (with Decals) and narrow graphic cover on the left side of the Header Sign.
Acrylic Diffuser
Edge of Block-out Panel
18.
Edge of Narrow Graphic Cover
Install the Block-out Panel.
Block-out Panel (with rubber feet toward sign)
Note: Rubber feet are touching the acrylic diffuser. The left edge of the Block-out Panel should be under the narrow graphic cover about 2". Instruction Sheet Part # 200261
Electronic Pricer Kit
19.
06.08.15 Page 8/10 Item # 10027
Plug Transformer power cord into pricer and route cord up and out the top.
Back of Pricer
20.
Screw thru the 8 1/4" Adapter into the back of the Electronic Pricer. Use the hole and slot that "center" the Pricer on the Adapter.
Center Pricer on Adapter.
Side View Instruction Sheet Part # 200261
06.08.15 Page 9/10 Item # 10027
Electronic Pricer Kit
1
21. 22. 23.
Place the Transformer over the top of the Header Sign, into the cord management tray.
2
3
Slide the Pricer/Adapter up into the top channel of the Header Sign, then push the bottom edge back against the acrylic diffuser and down into the lower channel of the Header Sign. Pull Pricer power cord snug over top of Header and cable tie to metal frame tubing. Pricer Power Cord Cable Tie Transformer
Rear View
WARNING: Do not over tighten cable tie. This could damage power cord insulation.
24. See installation sheet Power Cord Routing. GENERAL INFORMATION
25. Peel liner off tape, position and stick clear
storage pocket (with instructions, messages and decals) to the outside of the top drawer - left side.
Ins tru cti on s
Instruction Sheet Part # 200261
06.08.15 Page 10/10 Item # 10027
Electronic Pricer Kit
26.
Instructions for Setting Price and Messages.
8888 8888
Set Top Lock Set Bottom
Note: Price/messages to be set by store personnel.
Slide switch up or down to adjust top or bottom price. When flashing, push buttons to adjust digits. Turn message light on. Slide switch to middle to lock.
27.
Pick correct message from set and insert. Bow messages to fit under tabs in corners.
8888 8888
Remove Protective Film
CARTON Plus Tax Incl
Note: Store unused messages in storage pocket (see step 22).
28.
Based on need: Use Cover-up Decals to block out either the "Plus" or "Incl" text.
CARTON Plus Tax Incl
Note: Store unused cover-up decals in storage pocket (see step 22). Instruction Sheet Part # 200261
Electronic Pricer Kit Contents:
Instru ctions
CARTON
Securing Clips (2)
(2) Transformer (2) 8 1/4" Adapter (6) Message Set (2) Block-Out (12) Pieces Total) Panel
Securing Tape Set of (3) (2) #10-32 (4) #6-32 (2) Cable Ties (2) Electronic Pricer x 1 1/4” x 5/8” Screws Screws NOTE: May contain extra hardware not required.
(1) Storage Pocket w/ Instruction Card
Block Out Decals Set of (3)
Cover Up Decals Set of (9)
1. Determine location of Electronic Pricers.
(or)
Flip-Up Lighted Sign - 5 1/2" Instruction #'s 2-9
Header Lighted Sign - 8 1/4" Instruction #'s 10-21
The Electronic Pricers can be mounted to Flip Signs or Header Signs. This kit contains the required components to mount (2) Pricers. The instruction sheet first covers installation of the pricer onto a Flip Sign, then onto a Header Sign, and then general information.
Instruction Sheet Part # 200261
06.08.15 Page 2/10 Item # 10027
Electronic Pricer Kit
2.
Installation of Pricer onto a Flip Sign.
Remove (2) screws holding right side end cap on.
WARNING: This step must be done or damage to the power cord may occur.
3.
Feed the Transformer cord thru the coiled power cord and thru the (2) ball chain loops of the Flip Sign. Transformer Plug
Ball Chains
Side View Flip Sign
Instruction Sheet Part # 200261
06.08.15 Page 3/10 Item # 10027
Electronic Pricer Kit
4.
Remove the full length clear graphic cover, it is not used with the pricer.
5.
Slide the acrylic diffuser out the end of the sign a couple of inches. Wrap a Block-Out Decal around the far right edge. Make sure the decal is along the edge of the diffuser. Slide the diffuser back into the sign.
Acrylic Diffuser
Block-out Decal
Instruction Sheet Part # 200261
06.08.15 Page 4/10 Item # 10027
Electronic Pricer Kit
6.
7.
Plug Transformer power cord into pricer and route cord out the side.
Start to slide the Blockout Panel into the sign channel (rubber pads touching the acrylic diffuser). When it is halfway in, start sliding the pricer into the sign channel as well. Continue sliding both pieces in together until the pricer is flush with Clear Graphic Cover the edge of the sign.
Block-out Panel (Rubber pads towards sign) Electronic Pricer
Note: The left edge of the Block-out Panel should always be sticking out from behind the left side of the pricer. Leave about an inch of the Blockout Panel exposed to the left side of the pricer. You will need to slide it behind the clear graphic cover.
8. 9.
Replace end cap. Apply (1) piece of black securing tape to the bottom of the Flip-up Sign and Electronic Pricer to keep Bottom of pricer from sliding left / Flip-up Sign right. PRESS FIRMLY.
Black Securing Tape Instruction Sheet Part # 200261
06.08.15 Page 5/10 Item # 10027
Electronic Pricer Kit Front view of installed electronic pricer
Edge of Narrow Clear Graphic Cover
Electronic Pricer
Block-out decal behind Pricer
Edge of Block-out Panel
WARNING: Failure to perform this step could result in the Pricer power cord becoming damaged.
10.
A Attach (1) securing clip to the right hand end cap of the Flip Up Lighted Sign with the opening “up” (as shown). B Attach (1) securing clip to the back of the Flip Up Lighted Sign with the opening “down” (as shown). C Press firmly to ensure the clips do not come off. 10. A
11.
10. B Cable tie Pricer power cord to Flip Sign power cord.
Secure Pricer power cord.
Electronic Pricer Securing Clips
Flip Sign power cord
Straighten and route cord along side of end cap and along back to Flip Sign power cord. Tuck Pricer power cord into securing clips. Cable tie to Flip Sign power cord. WARNING: Do not over tighten cable tie. This could damage power cord insulation WARNING: Raise and release the Flip Sign, looking carefully at the power cords to ensure there is no binding or pinching. Instruction Sheet Part # 200261
06.08.15 Page 6/10 Item # 10027
Electronic Pricer Kit
12. Install and adjust #10 x 32 x 1 1/4" black machine screws in both hinges. All signs should be adjusted to the same viewing angle.
Electronic Pricer
Adjustment Screw
Approx 5O Facing Up
13.
Note: 2' Flip signs on 2' OTP fixtures do not get pricers attached to them. The signs without pricers will naturally face upward approximately 5o, signs with pricers will naturally face downward slightly. Adjust the screws on the flip signs with pricers so that they also face upward approximately 5o.
Installation of Pricer onto a Header Sign.
Remove clear graphic cover by lifting at finger notch and pulling slightly forward and down.
Narrow Graphic Cover
Do the same with the narrow graphic cover.
Full Length Clear Graphic Cover
Finger Notch
WARNING: Unplug and turn off power before Step #11
14.
Remove Acrylic Diffuser by lifting, then pulling slightly forward and down.
Acrylic Diffuser
Instruction Sheet Part # 200261
06.08.15 Page 7/10 Item # 10027
Electronic Pricer Kit
15.
Place a black Block-out Decal along the edge of the right side of the Acrylic Diffuser.
Acrylic Diffuser
17.
16.
Reinstall the Acrylic Diffuser.
Block-out Decal
Acrylic Diffuser
Reinstall the Tobacco Representative Instruction Packet (with Decals) and narrow graphic cover on the left side of the Header Sign.
Acrylic Diffuser
Edge of Block-out Panel
18.
Edge of Narrow Graphic Cover
Install the Block-out Panel.
Block-out Panel (with rubber feet toward sign)
Note: Rubber feet are touching the acrylic diffuser. The left edge of the Block-out Panel should be under the narrow graphic cover about 2". Instruction Sheet Part # 200261
Electronic Pricer Kit
19.
06.08.15 Page 8/10 Item # 10027
Plug Transformer power cord into pricer and route cord up and out the top.
Back of Pricer
20.
Screw thru the 8 1/4" Adapter into the back of the Electronic Pricer. Use the hole and slot that "center" the Pricer on the Adapter.
Center Pricer on Adapter.
Side View Instruction Sheet Part # 200261
06.08.15 Page 9/10 Item # 10027
Electronic Pricer Kit
1
21. 22. 23.
Place the Transformer over the top of the Header Sign, into the cord management tray.
2
3
Slide the Pricer/Adapter up into the top channel of the Header Sign, then push the bottom edge back against the acrylic diffuser and down into the lower channel of the Header Sign. Pull Pricer power cord snug over top of Header and cable tie to metal frame tubing. Pricer Power Cord Cable Tie Transformer
Rear View
WARNING: Do not over tighten cable tie. This could damage power cord insulation.
24. See installation sheet Power Cord Routing. GENERAL INFORMATION
25. Peel liner off tape, position and stick clear
storage pocket (with instructions, messages and decals) to the outside of the top drawer - left side.
Ins tru cti on s
Instruction Sheet Part # 200261
06.08.15 Page 10/10 Item # 10027
Electronic Pricer Kit
26.
Instructions for Setting Price and Messages.
8888 8888
Set Top Lock Set Bottom
Note: Price/messages to be set by store personnel.
Slide switch up or down to adjust top or bottom price. When flashing, push buttons to adjust digits. Turn message light on. Slide switch to middle to lock.
27.
Pick correct message from set and insert. Bow messages to fit under tabs in corners.
8888 8888
Remove Protective Film
CARTON Plus Tax Incl
Note: Store unused messages in storage pocket (see step 22).
28.
Based on need: Use Cover-up Decals to block out either the "Plus" or "Incl" text.
CARTON Plus Tax Incl
Note: Store unused cover-up decals in storage pocket (see step 22). Instruction Sheet Part # 200261
