Fitbit charge HR Disassembly
Fitbit charge HR Disassembly
Fitbit charge HR Disassembly Fitbit charge teardown. It stopped working and was sent a new one so tore old one open...wondering if possible to replace battery (cant find a replacement) as the voltage is 0. LSSP031420AB lipoly battery.
Written By: Hunter
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 4
Fitbit charge HR Disassembly
INTRODUCTION Fitbit charge teardown. It stopped working and was sent a new one so tore old one open...wondering if possible to replace battery (cant find a replacement) as the voltage is 0. LSSP031420AB lipoly battery.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 4
Fitbit charge HR Disassembly
Step 1 — Removing the guts
Remove all four T3 Torx screws. Then "pop" out the electronics by pressing in the reset hole and pushing out the side with a pin. Use your thumb and push it up towards the wrist band clip (top in this picture). The unit "slides" up and out.
Step 2 — Remove top board to expose battery
To access the lipo, remove the two screws above the screen. Pull the circular vibrating motor out and pull out the board.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 4
Fitbit charge HR Disassembly
Step 3 — Exploring the inside
Image 3a) Two inner screws removed, case gently pried open.
Image 3b) Obverse, showing battery glued onto the circuit. Be careful when prying this up as it could pull off the other connectors.
Expanded view showing battery pried out.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-16 03:56:21 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 4
Fitbit charge HR Disassembly Fitbit charge teardown. It stopped working and was sent a new one so tore old one open...wondering if possible to replace battery (cant find a replacement) as the voltage is 0. LSSP031420AB lipoly battery.
Written By: Hunter
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 4
Fitbit charge HR Disassembly
INTRODUCTION Fitbit charge teardown. It stopped working and was sent a new one so tore old one open...wondering if possible to replace battery (cant find a replacement) as the voltage is 0. LSSP031420AB lipoly battery.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 4
Fitbit charge HR Disassembly
Step 1 — Removing the guts
Remove all four T3 Torx screws. Then "pop" out the electronics by pressing in the reset hole and pushing out the side with a pin. Use your thumb and push it up towards the wrist band clip (top in this picture). The unit "slides" up and out.
Step 2 — Remove top board to expose battery
To access the lipo, remove the two screws above the screen. Pull the circular vibrating motor out and pull out the board.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 4
Fitbit charge HR Disassembly
Step 3 — Exploring the inside
Image 3a) Two inner screws removed, case gently pried open.
Image 3b) Obverse, showing battery glued onto the circuit. Be careful when prying this up as it could pull off the other connectors.
Expanded view showing battery pried out.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-16 03:56:21 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 4
