flat base tv stand 1 flat base tv stand 1 - Displays2go
FLAT BASE TV STAND Parts A. B. C1. C2. D1. D2. E. F.
Instructions Metal Base Lower Round Tube Lower Round Tube Upper Round Tube Upper Round Tube Tube Connector Pan Head Screw
1 1 1 1 1 1 2 12
(Left) (Right) (Left) (Right)
A
B
E
F
C1
C2
D1
D2
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE START THE ASSEMBLING. Open small box, lay out 4 long Tubes (C1, C2, D1, D2) on a flat surface. See picture below to identify where each tube goes to (upper or lower, left or right).
1
3b
RIGHT VIEW
LEFT VIEW
BACK VIEW
3a
2 2 Upper Right Tube
D2
LEFT VIEW
RIGHT VIEW
D1
BACK VIEW
Upper Left Tube
Lower Right Tube C2 C1 CAUTION: 1. METAL BASE IS HEAVY! AT LEAST 2 PEOPLE SHOULD LIFT/MOVE TO PREVENT ANY PHYSICAL INJURY FROM MISHANDLING. 2. ALWAYS PLACE THE UNIT ON A HARD, FLAT SURFACE. DO NOT PLACE THE UNIT IN WHERE IT MAY BE IMPACTED OR MOVED. FAILURE TO DO SO COULD CAUSE SEVERE BODILY INJURY. Lower Left Tube
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
1
FLAT BASE TV STAND
2
ALL SCREWS MUST BE SECURELY TIGHTENED BEFORE USING TV STAND. Fix Tube Connector (Part E) on top of the Before assembling, remove packing materials. Lower Tube. Carefully place the Metal Base (Part B) on a hard, flat ground.
4
Holes at top of Lower Tubes should face outward, to align with the holes on Tube Connectors. (See STEP 4)
C1
E
Insert Tube Connectors (Part E) into the Fixed Lower Tubes. Hold it in place when lining up holes. (Align with the top holes on Lower Tubes)
C2 Insert 4 Screws (Part F) through Lower Tubes into Connectors. Fasten screws with hex key.
Insert Lower Tube into the upright on the Metal Base.
Ensure slot cutouts on uprights and Lower Tubes align with each other.
Insert Upper Tubes with Connectors.
D1
D2
Ensure the 2 slot cutouts are facing the same direction as other cutouts on the Lower Tubes.
B
3
5
Fix Lower Tubes by tightening 4 screws at bottom of the TV Stand.
Insert Upper Tubes (Part D) intoTube Connectors from above. The holes should line up with the holes on Connectors. Fasten 4 Screws (Part F) with hex key.
F
Tighten 4 Screws (Part F) against the surface of lower poles with hex key.
If securing the whole unit to the floor, use hardware through 4 corner holes to fix the base.
Still have questions? No worries. If you’re confused during any step, just call the number located at the bottom of the Instruction pages. Our friendly representative will be more than happy to assist you.
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
2
FLAT BASE TV STAND CAUTION: 1. 2. 3. 4.
For 2 TVs hanging ONLY AT LEAST 2 PEOPLE SHOULD LIFT/HANG TVs. BE CAREFUL IF USE LADDERS OR STANDING ABOVE THE GROUND. DO NOT ADJUST THE POSITION OF EXTRUSION WHEN TV IS ON THE BRACKET. DO NOT USE CASTERS. HOLES IN THE BASE ARE FOR MOUNTING ONTO FLOOR ONLY.
1. Before starting, measure and calculate the minimum distance between 2 TVs while hanging on FLTBSPTBBK, without interfering with each other.
Distance between 2 TVs
NOTE: (1) FLTBSPTBBK can hold dual flat TVs up to 70”, depending on different layouts and orientation. (2) TVs can not be rotated while 2 TVs are hung on the stand at the same time. (3) Image on the right shows 2 same size TVs, which the height is the minimum distance required. STEP 1. must be done if hanging 2 different size TVs, or hanging any 2 TVs at different orientations.
2. Avoid fastening Extrutions at the joint area of 2 3. Hang the lower TV first, then the upper one. It Tubes, where screws could interfere with the Extru- could be difficult to hang the lower TV last as there might not be enough room. sions.
2nd operation Hang Upper TV
Extrution 1st operation Hang Lower TV
Tube * TIPS: Adjust Extrution up and down as needed for desired result.
* TIPS: It is easier to accomplish this task by increasing the gas between 2 TVs. Bracket mounted on TV can be adjusted up and down to best fit and locate both TVs on the stand.
Still have questions? No worries. If you’re confused during any step, just call the number located at the bottom of the Instruction pages. Our friendly representative will be more than happy to assist you.
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
3
Instructions Metal Base Lower Round Tube Lower Round Tube Upper Round Tube Upper Round Tube Tube Connector Pan Head Screw
1 1 1 1 1 1 2 12
(Left) (Right) (Left) (Right)
A
B
E
F
C1
C2
D1
D2
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE START THE ASSEMBLING. Open small box, lay out 4 long Tubes (C1, C2, D1, D2) on a flat surface. See picture below to identify where each tube goes to (upper or lower, left or right).
1
3b
RIGHT VIEW
LEFT VIEW
BACK VIEW
3a
2 2 Upper Right Tube
D2
LEFT VIEW
RIGHT VIEW
D1
BACK VIEW
Upper Left Tube
Lower Right Tube C2 C1 CAUTION: 1. METAL BASE IS HEAVY! AT LEAST 2 PEOPLE SHOULD LIFT/MOVE TO PREVENT ANY PHYSICAL INJURY FROM MISHANDLING. 2. ALWAYS PLACE THE UNIT ON A HARD, FLAT SURFACE. DO NOT PLACE THE UNIT IN WHERE IT MAY BE IMPACTED OR MOVED. FAILURE TO DO SO COULD CAUSE SEVERE BODILY INJURY. Lower Left Tube
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
1
FLAT BASE TV STAND
2
ALL SCREWS MUST BE SECURELY TIGHTENED BEFORE USING TV STAND. Fix Tube Connector (Part E) on top of the Before assembling, remove packing materials. Lower Tube. Carefully place the Metal Base (Part B) on a hard, flat ground.
4
Holes at top of Lower Tubes should face outward, to align with the holes on Tube Connectors. (See STEP 4)
C1
E
Insert Tube Connectors (Part E) into the Fixed Lower Tubes. Hold it in place when lining up holes. (Align with the top holes on Lower Tubes)
C2 Insert 4 Screws (Part F) through Lower Tubes into Connectors. Fasten screws with hex key.
Insert Lower Tube into the upright on the Metal Base.
Ensure slot cutouts on uprights and Lower Tubes align with each other.
Insert Upper Tubes with Connectors.
D1
D2
Ensure the 2 slot cutouts are facing the same direction as other cutouts on the Lower Tubes.
B
3
5
Fix Lower Tubes by tightening 4 screws at bottom of the TV Stand.
Insert Upper Tubes (Part D) intoTube Connectors from above. The holes should line up with the holes on Connectors. Fasten 4 Screws (Part F) with hex key.
F
Tighten 4 Screws (Part F) against the surface of lower poles with hex key.
If securing the whole unit to the floor, use hardware through 4 corner holes to fix the base.
Still have questions? No worries. If you’re confused during any step, just call the number located at the bottom of the Instruction pages. Our friendly representative will be more than happy to assist you.
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
2
FLAT BASE TV STAND CAUTION: 1. 2. 3. 4.
For 2 TVs hanging ONLY AT LEAST 2 PEOPLE SHOULD LIFT/HANG TVs. BE CAREFUL IF USE LADDERS OR STANDING ABOVE THE GROUND. DO NOT ADJUST THE POSITION OF EXTRUSION WHEN TV IS ON THE BRACKET. DO NOT USE CASTERS. HOLES IN THE BASE ARE FOR MOUNTING ONTO FLOOR ONLY.
1. Before starting, measure and calculate the minimum distance between 2 TVs while hanging on FLTBSPTBBK, without interfering with each other.
Distance between 2 TVs
NOTE: (1) FLTBSPTBBK can hold dual flat TVs up to 70”, depending on different layouts and orientation. (2) TVs can not be rotated while 2 TVs are hung on the stand at the same time. (3) Image on the right shows 2 same size TVs, which the height is the minimum distance required. STEP 1. must be done if hanging 2 different size TVs, or hanging any 2 TVs at different orientations.
2. Avoid fastening Extrutions at the joint area of 2 3. Hang the lower TV first, then the upper one. It Tubes, where screws could interfere with the Extru- could be difficult to hang the lower TV last as there might not be enough room. sions.
2nd operation Hang Upper TV
Extrution 1st operation Hang Lower TV
Tube * TIPS: Adjust Extrution up and down as needed for desired result.
* TIPS: It is easier to accomplish this task by increasing the gas between 2 TVs. Bracket mounted on TV can be adjusted up and down to best fit and locate both TVs on the stand.
Still have questions? No worries. If you’re confused during any step, just call the number located at the bottom of the Instruction pages. Our friendly representative will be more than happy to assist you.
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
3
