GE 30" Built-In Single Convection Wall Oven

SHOP DRAWING, PRODUCT DATA OR SAMPLE TRANSMITTAL

PLANNING•ARCHITECTURE•ENGINEERING•INTERIORS 5307 E Mockingbird Lane, Ste 400 Dallas, TX 75206

NO.

339.0

DATE

August 12, 2016

PROJECT NAME

Vintage

DALY PROJECT NO. 012-10362-000 CONTRACTOR

Carmel Partners

CONTRACTOR JOB NO.

1ST Submittal

X

(Indicate by X)

Resubmittal

(Indicate by X)

IF RESUBMITTAL, PREVIOUS TRANSMITTAL NO. OF ITEM BEING RESUBMITTED: Specification Section & Paragraph No.

Description of Product or Equipment

Manufacturer

Drawing or Data No.

Amenity Appliances

Sample (Mark X)

X

Action Taken by A/E

C

a.

The above submittal has been reviewed and approved by the Contractor in accordance with provisions of the General Conditions for this project, and there are no deviations from the requirements of the Contract Documents. _____ (Indicate by X); or,

b.

The above submittal has been reviewed and approved by the Contractor in accordance with the provisions of the General Conditions for this project with any specific deviations from the requirements of the Contract Documents clearly identified. _____ (Indicate by X – note: if this is actually a Substitution, a separate Substitution Application Form must be attached, clearly documenting how the Owner would benefit from such a contract change; the submittal will not be returned until Substitution Application has been acted upon)

Contractor's Signature

Contractor

Street Address or P.O. Box No.

City, State

SPACE BELOW FOR ARCHITECT USE ONLY The above submittal has been reviewed by the Architect in accordance with the General Conditions for this project and is returned with action as indicated in the legend below. Shop drawings and other submittals are part of the Contractor’s own Work Plan and are not Contract Documents. Architect’s review of Contractor's submittals is only for the limited purpose of checking for conformance with the design concept expressed in the Contract Documents. Architect’s review of such submittals is not conducted for the purpose of determining the accuracy and completeness of other details such as dimensions and quantities, or for substantiating instructions for installation or performance of equipment or systems, all of which remain the sole responsibility of the Contractor. Architect's review of Contractor's submittals cannot change the Contract Documents and cannot relieve the Contractor of any obligations under the Contract. The Architect's review shall not constitute approval of Contractor’s safety precautions or of any construction means, methods, techniques, sequences or procedures.

A - No Exceptions Noted

B - Exceptions C - Revise and Noted (do not Resubmit resubmit) (See Notes)

D - Rejected

By (reviewer initials):

7-8-09

SMD

E - Not Required Returned without Action

Date: Aug 18, 2016

LAD 00840-1

Carmel to review for final substitution.

SUBSTITUTION REQUEST TO

Carmel Partners

PROJECT

Vintage

SPECIFIED ITEM

Viking VIPR162RSS w/ interior power ventilator kit #VIDV500

SECTION ID Plan

PAGE ID7.11

PARAGRAPH

Tag E2

DESCRIPTION Clubroom electric cooktop - downdraft with ventilator kit PROPOSED SUBSTITUTION Viking VDD5360SS Downdraft & VDVI600 Internal Blower Attached data includes product description, specifications, drawings, photographs, performance and test data adequate for evaluation of request including identification of applicable data portions. Attached data also includes description of changes to Contract Documents and proposed substitution requires for proper installation.

Undersigned certifies following items, unless modified by attachments, are correct: 1. 2.

Proposed substitution does not affect dimensions shown on drawings. Undersigned pays for changes to building design, including engineering design, detailing, and construction costs caused by proposed substitution. Proposed substitution has no adverse effect on other trades, construction schedule, or specified warranty requirements. Maintenance and service parts available locally or readily obtainable for proposed substitution.

3. 4.

Undersigned further certifies function, appearance, and quality of proposed substitutions are equivalent or superior to specified item. Undersigned agrees to terms and conditions for substitutions found in Bidding Documents to this proposed substitution. Submitted By:

Dusty Jones Name (Printed or typed)

General Contractor (if after award of Contract)

Signature

For use by A/E

Ferguson Firm Name Address City, State, Zip

____Approved

____Approved as noted

____Not Approved

____Received too late

By

08/12/16 Date

Date

415-527-8086 Tel:

Remarks

Carmel to review for final substitution. SUBSTITUTION REQUEST Is this the correct item #???

TO

Carmel Partners

PROJECT

Vintage

SPECIFIED ITEM

GE GLDA696FSS

SECTION ID Plan

PAGE ID7.11

PARAGRAPH Tag E14

DESCRIPTION Workroom Refrigerator PROPOSED SUBSTITUTION

GE PZS22MSKSS

Attached data includes product description, specifications, drawings, photographs, performance and test data adequate for evaluation of request including identification of applicable data portions. Attached data also includes description of changes to Contract Documents and proposed substitution requires for proper installation.

Undersigned certifies following items, unless modified by attachments, are correct: 1. 2.

Proposed substitution does not affect dimensions shown on drawings. Undersigned pays for changes to building design, including engineering design, detailing, and construction costs caused by proposed substitution. Proposed substitution has no adverse effect on other trades, construction schedule, or specified warranty requirements. Maintenance and service parts available locally or readily obtainable for proposed substitution.

3. 4.

Undersigned further certifies function, appearance, and quality of proposed substitutions are equivalent or superior to specified item. Undersigned agrees to terms and conditions for substitutions found in Bidding Documents to this proposed substitution. Submitted By:

Dusty Jones Name (Printed or typed)

General Contractor (if after award of Contract)

Signature

For use by A/E

Ferguson Firm Name Address City, State, Zip

____Approved

____Approved as noted

____Not Approved

____Received too late

By

08/12/16 Date

Date

415-527-8086 Tel:

Remarks

CARMEL PARTNERS

THE VINTAGE

LUB-ROOM & WORK-ROOM) PLEASANTON, CALIFORNIA

FERGUSON CONTACT DUSTY JONES 415-527-8086 [email protected]

Need a freezer installed next to the 2-drawer refrigerator. VT65M7BISSHVADA

704 N. Laverne Ave. Fresno, CA 93727

CARMEL PARTNERS THE VINTAGE - CLUBROOM & WORK ROOM PLEASANTON, CA REVISED FEBRUARY 18, 2016 PRODUCT/LINK

DESCRIPTION

CLUBROOM - RESIDENTIAL APPLIANCES RVGC3365BSS Viking - 36" Gas Cooktop with 5 Permanently Sealed Burners VDD5360SS Viking - 36" Downdraft Ventilation System w/ Multiple Blower Options VDVI600 Viking - 600 CFM Internal Blower * GE - 30" Single Electric Wall Oven Self-Cleaning w/ Convection - ADA JT5000SFSS GE Profile - 30" Warming Drawer - ADA PW9000SFSS SP6DS2D7ADA Summit - 24" Double Drawer Refrigerator - ADA GE - Top Control Dishwasher - E-STAR - ADA GLDT696DSS JMD2124WS Jenn - Air - 24" Stainless Steel Under Counter Microwave Drawer 30IMAT-BS-F-R Marvel - Undercounter Ice Machine - solid stainless steel right hinge door - no factory installed drain pump GFC535V GE - 1/2 HP Continuous Feed Garbage Disposal - Corded SCR600LBIADA Summit - Undercounter Drink Refrigerator - ADA APPLIANCE PACKAGE TOTAL

WORKROOM - RESIDENTIAL APPLIANCES GE - Front Control Dishwasher - ADA (losing E-Star in 2016) GLDA696FSS PZS22MSKSS GE Profile - 22.1 Cu. Ft. Counter-Depth Side-by-Side Refrigerator GE Profile - 1.1 cu. ft. Countertop Microwave - ADA PEM31SFSS APPLIANCE PACKAGE TOTAL

INSTALLATION ACCESSORIES IBS9C 3/8 Black MI 150# ST 90 ELL - Cooktop BCSSD4K36 1/2 MIP X 1/2 FIP Ball X 36 Connector - Cooktop RAP33003 16/3 3FT ANG Power Supply Cord - Hood BBP87 7" Damper - Hood DIV750RC841 Romex Connector - Hood DIVPI328 Split Bolt Connector (X 4 per unit) - Built-In Oven B804DC2 Angle Connector - Built-In Oven S52C6 Plate Cover - Built-In Oven PFSSHC6712 1/2 SS Hose Clamp - Dishwasher PFXSD6C72ET LF 3/8X3/8 72 Connector w/ FHT ELL - Dishwasher RAP33002 16/3 6FT STR Power Supply Cord - Dishwasher DIV750RC841 Romex Connector - Dishwasher PFX146205 LF 1/4X1/4 60 SS Ice-Maker Connector - Refrigerator APPLIANCE PACKAGE TOTAL

NON-UNION & NON-PREVAILING WAGE LABOR LABOR LABOR LABOR LABOR LABOR

COOKTOP DOWNDRAFT VENT & BLOWER** WALL OVEN WARMING DRAWER DOUBLE DRAWER REFRIGERATOR

LABOR LABOR LABOR LABOR LABOR LABOR LABOR

DISHWASHER UNDERCOUNTER MICROWAVE DRAWER UNDERCOUNTER ICE MACHINE DISPOSAL - INSTALLED BY OTHERS UNDERCOUNTER REFRIGERATOR REFRIGERATOR COUNTERTOP MICROWAVE LABOR TOTAL PRICING BASED ON [1] STOP DELIVERY / INSTALLATION FOR COMPLETION OF ENTIRE PROJECT ADDITIONAL STOPS WILL INCUR A TRIP CHARGE CREDIT FOR OCIP: PROJECT TOTAL (ALL SERVICES INCLUDED)

* Blower may require additional parts for installation depending on installation location ** Listed labor price is to install the blower in the bottom cabinet (other blower locations may incur labor increase)

Terms & Conditions on following page

GENERAL TERMS & CONDITIONS OF INSTALLATION SERVICES •Pricing is based on elevator use or lift to units, NO STAIRS. Stairs quote available per request. •Disposal installation does not fall under Ferguson's scope of work. This task is completed by Plumber. •This bid does not include parking fees. If they are required please advise and quote will be provided. •Long appliance hauls or delays due to entrances being blocked need to be assessed for delays and backcharge. • Requested installation dates need a minimum 10 day lead time for scheduling. •Door swing reversal for Refrigerator and Laundry not included. Quote available upon request. •Based on GC provided existing hook ups. Modifications or alterations are outside of scope, and installers are not qualified for such work. Ferguson is not responsible for work performed by other related subcontractors. •Install prices for laundry include standard 4 ft hoses. If 6 ft hoses are determined to be needed due to closet constraints at jobsite walk, then a change to 6 ft hoses will be charged. •Serial numbers are located on appliances and in most use and care manuals. Close out warranty packets show location of info for easy tenant finding. Serial number recording is a lengthy time consuming process for the installers, causing a degree of delay. If requested, serial number recording per unit & entered into an organized spreadsheet is an additional $5 (Non Union) or $23 (Union) per a kitchen charge. •Saturday delivery/installation requires a 3 week lead time for scheduling and overtime charges will apply. •Appliance warranty is run by certified manufacture technicians, separate entities. Ferguson will assist with contracted customer for warranty items until job turn over. At this time, the warranty close out packet is given with detailed information for property management to utilize manufacture warranties directly. Ferguson will explain the process if needed. •Aesthetic Warranty: Manufacture gives 72 hours for aesthetic warranty to be reported by GC Supervisor walk. After this time, parts can be considered trade damage. This is a timely process, and damages need to be reported immediately. •Recipient of appliances (GC or someone acting on the GC’s behalf) must sign off on all appliances upon delivery. •If cycle test is unable to be performed due to site readiness issues, $65 return to site charge per stop, plus $25 cycle test charge per appliance.

GENERAL TERMS & CONDITIONS OF SUPPLY •Due to the nature of Ferguson's role as a supplier of ready to use appliances, installation is a third party sub tiered service we oversee and project manage solely. Therefore, retention will be held on the labor portion of the contract only. •Manfacturer warranties are valid for one year from the substantial completion date of the project. Extended warranties may be available upon request, please inquire for more information. •Appliances are based on current Department of Energy Star Ratings from date of quote. Ferguson and Manufacture are not responsible for DOE change of energy star qualifications and subject to change on short notice. •Model numbers and discontinuations are subject to change without notice by manufacturer. This may include price differences for non-transitional product out of supplier's control. •Lift-gates for delivery trucks are not included in above pricing. Pricing is available upon request. •Final quantities are to be approved by purchaser before final contract is written. PRICE VALID THROUGH - 03/31/16

GAS COOKTOPS

RVGC330-5B – 30” WIDE RVGC336-5B – 36” WIDE

®

Features and Functions

Easy Operation and Cleanup

• Wide variety of BTU ratings to accommodate all types

• Permanently sealed burners – spills cannot enter burner box

of surface cooking needs – 30” wide model – 5 burners • Left front – 9,100 BTU • Left rear – 9,100 BTU • Center – 17,000 BTU • Right front – 12,000 BTU

• One-piece, extremely durable steel top with separate spill collection areas • Durable metal die-cast knobs with child-proof, push-to-turn safety feature • Customer-removable knobs, grates, and burners/caps for easy cleaning

• Right rear – 5,000 BTU

• Continuous grate design for easy movement of pots and pans

– 36” wide model - 5 burners

• Overall/burner box dimensions designed to fit majority of

• Left front – 9,100 BTU • Left rear – 9,100 BTU

similarly sized cooktop cutouts

• Center – 17,000 BTU

Installation Accessories

• Right front – 12,000 BTU

• LP conversion kit (RDLPKC)

• Right rear – 5,000 BTU • Sealed burners with aluminum flame ports and porcelainized, cast-iron burner caps

Finish • Available in Stainless Steel (SS)

• Exclusive – SureSpark™ Ignition System – Automatic electronic spark ignition/re-ignition surface burners light at any position on the knob and re-light if extinguished, even on lowest setting

– Finish designates top; all units have black porcelain grates and burner caps

Warranty Highlights • One-year full – complete product • Ninety-day full – cosmetic parts such as glass, painted items, and decorative items • Five-year limited – surface burners

30” Wide Gas Cooktop

36” Wide Gas Cooktop

GAS COOKTOPS

RVGC330-5B – 30” WIDE RVGC336-5B – 36” WIDE

®

GAS 30”AND 36” WIDE COOKTOPS

DESCRIPTION

RVGC330-5B

RVGC336-5B

Overall Width

30 3/4” (78.1 cm)

Overall Height

4 3/8” (13.7 cm)

Overall Depth

21" (53.3 cm)

Cutout Width

29 1/4” (74.3 cm) minimum 29 7/8” (75.9 cm) maximum

Cutout Height

3 1/8” (7.9 cm)

Cutout Depth

20” (50.8 cm) minimum; 20 1/4” (51.4 cm) maximum

Gas Requirements

Ships Natural or LP/Propane; Field convert with conversion kit (purchased separately); accepts standard residential 1/2” (1.3 cm) ID gas service line.

Electrical Requirements

120VAC/60Hz; 4 ft. (121.9 cm), 3-wire cord with grounded 3-prong plug attached to product

Maximum Amp Usage

2.0 amps

Surface Burner Rating

Left Front – 9,100 BTU Left Rear – 9,100 BTU Center – 17,000 BTU Right Front – 12,000 BTU Right Rear – 5,000 BTU

Left Front – 9,100 BTU Left Rear – 9,100 BTU Center – 17,000 BTU Right Front – 12,000 BTU Right Rear – 5,000 BTU

Approximate Shipping Weight

49 lb. (22.0 kg)

74 lb. (33.3 kg)

36 3/4” (93.3 cm)

35 1/4” (89.5 cm) minimum 35 7/8” (91.1 cm) maximum

30

(78-3/4 .1 ” cm )

36

(93-3/4 .3 ” cm )

” 21 cm) .3

(53

. ax ” m m) 133.0 c

” 21 cm) .3

2-1/2”

(53

4-3/8”

(6.4 cm)

(3

in.

(11.1 cm)

”m ) 18 .7 cm

in. ”m ) 361.4 cm (9

(45

(

. in ) m m ” c 8 0.3 2

2-1/2”

(6.4 cm)

1-3/4”

(4.5 cm)

B

(

(9

” /2 ) -1 cm 2 .4 6

in. ”m ) 361.4 cm A C

A

VIKING RANGE, LLC ®

F60258

30”W. Model

36”W. Model

29 1/4” (74.3 cm) minimum 29 7/8” (75.9 cm) maximum

35 1/4” (89.5 cm) minimum 35 7/8” (91.1 cm) maximum

B

20” (50.8 cm) minimum; 20 1/4” (51.4 cm) maximum

C

3” (7.6 cm) min.

111 FRONT STREET

GREENWOOD, MISSISSIPPI 38930

USA

For detailed product information, model numbers, or to request a quote call 1-888-845-4641 or visit vikingrange.com © 2013 Viking Range, LLC | Specifications subject to change without notice.

0715

BUILT-IN REAR DOWNDRAFTS

®

Are the controls for the downdraft located for accessibility?

DESIGN AND APPEARANCE §§Coordinates with both Viking Professional and Viking cooktops and Viking Professional rangetops §§Compact design is installed directly behind a cooktop or rangetop for an unobtrusive appearance §§Available in 30”, 36”, 45” and 48” widths §§Thin profile provides additional space under the cabinet

PROFESSIONAL PERFORMANCE AND FEATURES §§Industry leading 18” high chimney rise is ideal for large pots and pans, capturing more smoke and odors than other downdrafts §§Brushed stainless steel cover with dishwasher-safe filters are easy to remove for cleaning §§Filter clean indicator takes the guesswork out of when to clean the filter §§Capacitive touch control on front and top §§Two level LED lighting (500 LUX) for bright surface illumination §§Four speed blower efficiently handles all types of cooking §§Heat sensor automatically adjusts speed of blower to high when excessive heat is detected

BLOWER OPTIONS §§VDVI600 – 600 CFM interior flex blower §§Unique ducting capability allows interior blower to be ducted

MODEL NUMBERS

left, right, down or as a remote mount

§§VDD5300SS – 30”W. Rear Downdraft

§§VDVE900 – 900 CFM external blower

§§VDD5360SS – 36”W. Rear Downdraft

§§VDVE1200 – 1200 CFM external blower

§§VDD5450SS – 45”W. Rear Downdraft

§§Optional ARKD accessory recirculating kit provides an option when outside ducting is not possible

§§VDD5480SS – 48”W. Rear Downdraft

ACCESSORIES

ACCESSORIES (CONTINUED)

WARRANTY

§§ARKD – Non-duct recirculation kit

§§VACE36 – End caps for 36-3/4”W. cooktop

§§1-year full covers complete unit

§§BPFD – Non-duct filter replacement

§§AXKD2 – 2’ of flexible duct

§§5-year limited covers downdraft blower

§§ATKD8 – Transition to 8” round

§§AXD5 – 5’ of extension cable for flex

§§ATKD10 – Transition to 10” round

blower remote use

§§RCVD8 – Front panel rough-in for remote flex blower 8” §§RCVD10 – Front panel rough-in for remote flex blower 10”

COLOR FINISHES §§Available in Stainless Steel (SS)

BUILT-IN REAR DOWNDRAFTS

®

B U I LT- I N R E A R D O W N D R A F T S MODEL NUMBER

CFM

RECOMMENDED DUCT SIZE

MAX DUCT RUN

120 V/60 HZ MAX AMPS

VDVI600 (interior) – NEW

600

8” round

40 feet (12.2m)

3.0

VDVE900 (exterior) – NEW

900

10” round

50 feet (15.2m)

5.7

VDVE1200 (exterior) – NEW

1200

10” round

50 feet (15.2m)

6.0

Please do not prepare installation from brochure data only. See installation instructions for important clearance/installation information.

VIKING R ANGE, LLC

111 FRONT STREET

30”W. Model

36”W. Model

45”W. Model

48”W. Model

A

47.875”

47.875”

47.875”

47.875”

B

18.5”

18.5”

18.5”

18.5”

C

27.375”

33.375”

43.375”

45.375”

D

2.25”

2.25”

2.25”

2.25”

E

25.5”

31.5”

40.5”

43.5”

F

1.75”

1.75”

1.75”

1.75”

G

29.375”

29.375”

29.375”

29.375”

H

27.125”

33.125”

42.125”

45.125”

I

2.5”

2.5”

2.5”

2.5”

GREENWOOD, MISSISSIPPI 38930 USA

For detailed product information, model numbers, or to request a quote call 1-888-845-4641 or visit vikingrange.com © 2015 Viking Range, LLC All rights reserved. Specifications subject to change without notice. F60343A

0715

23-1/2" MIN

9-1/2" MAX.

Junction box location

F

JT5000SF

Cutout depth 23-1/2" MIN

F 9-1/2" MAX.

Junction box 22" to location bottom of

GE 30" Built-In Single Convection Wall Oven

Cutout depth 23-1/2" MIN

junction box Conduit Cutout width DIMENSIONS INFORMATION (IN 28-1/2" INCHES) MIN. 40" AND INSTALLATION 22" to 28-5/8" MAX. bottom of MOST 30" WALL CABINETS CAN BE junction box Conduit Cutout width USED 28-1/2" MIN. 40" WITH THIS UNIT. NOTE: These D ovens are not approved for stackable installations. Cabinets installed adjacent to wall ovens must have an adhesion specDof at least a 194°F temperature rating. 22 " handle protrudes 3" from door face. Door

22 "

Cabinets and drawers on adjacent 45° and 90° walls should be placed to avoid interference with the handle.

Conduit Junction box 40" location

E

28-5/8" MAX.

A B A B C

Electric wall ovens are not approved for installation with a plug and receptacle. They must be hard wired in accordance with installation instructions. INSTALLATION INFORMATION: Before installing, consult installation instructions packed with product for ­ current dimensional data.

F

Cutout heightC 27-1/4" MIN. 27-5/16" MAX.

Recommended cutout location from floor 32-1/2"

30''

D

Conduit 40"

Cutout height E 27-1/4" MIN. 27-5/16" MAX.

Cutout width 28-1/2" MIN. 28-5/8" MAX

22 "

D

Recommended cutout location from floor 23" minimum 32-1/2"

22" to bottom of junction box

A

23" minimum door opening 22 " allowance

B C

door opening allowance

30'' PT7050 JT5000 JT3000 JT1000

PT7050 JT5000 JT3000 JT5000 JT1000

30'' CL

Side-by-side installations rerquire CL 2 x 4 or 2 x 4 or 2 x 4 or at equivalent least 2" between runnerscutouts. equivalent runners equivalent runners level with bottom of cutout with level withlevel bottom of bottom cutout of cutout Cabinet 30" Cabinet 30" and flush with sides of cutout KW RATING and flush with sides with of cutout and flush sides of cutout A – Overlap of oven top of cutout 1" or solid bottom floor. A –atOverlap of oven at top of cutout 1" or solid bottom floor. or solid4.2 bottom floor. 240V B – Overlap of oven side ofofedges cutout 3/4" of cutout B –over Overlap ovenofover side of edges 3/4" C – Overlap of oven at bottom of cutout 1-1/4" 208V 3.2 Suitable C – Overlap of oven at bottom of cutout 1-1/4" Suitable Oven bracing BREAKER SIZE bracing Oven (must support 200 lbs.) to200 support (must support lbs.) D – Install depth 23-1/2" to support 240V 20 Amps runners runners D – Install depth 23-1/2" s.) E – Overall height with trim 28-5/8" t 200 lbs.) 208V 20 Amps 28-5/8" F – Overall widthE – Overall height with trim 29-3/4" F – Overall width 29-3/4"

ADA

For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.

COMPLIANT

2 x 4 or equivalent runners level with bottom of cutout and flush with sides of cutout Cabinetfloor. or solid bottom

A – Overlap of oven at top of cutout B – Overlap of oven over side of edges C – Overlap of oven at bottom of cutou Oven D – Install depth E – Overall height with trim F – Overall width

Listed by Underwriters Laboratories

Specification Revised 4/16

JT5000SF

GE 30" Built-In Single Convection Wall Oven OPTIONAL UNDERCOUNTER DIMENSIONS AND INSTALLATION INFORMATION NOTE: 36" ribbon cooktop are approved for use over GE 30" single wall ovens and warming drawers. 30" ribbon cooktops are approved for use over 30" and GE 27" single wall ovens and warming drawers. Refer to cooktop and wall oven installation information packed with products for current dimensional data.

Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. Gas or electric connections for gas cooktop must be located in an adjacent accessible location to the right

240V / 208V Junction box location

25

9-1/2"

Note: Door handle protrudes 3" from door face. Cabinets and drawers on adjacent 45° and 90° walls should be placed to avoid interference with the handle. Installation information: Before installing, consult installation instructions packed with products for current dimensional data and for alternate installation options.

28 1/2" MIN. 28 5/8" MAX. 27 1/4" MIN. 27 5/16" MAX.

Allow 1-1/4" top/bottom and 1" on sides for overlap

ELECTRIC WALL OVENS ARE NOT APPROVED FOR INSTALLATION WITH A PLUG AND RECEPTACLE. THEY MUST BE HARD WIRED IN ACCORDANCE WITH INSTALLATION INSTRUCTIONS.

36" Typical countertop height

22" MIN. Above support platform

24

4" 3/4" Support platform required

Must Support 200 Lbs.

Dimension and installation information are shown in inches.

ADA

For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.

COMPLIANT

Listed by Underwriters Laboratories

Specification Revised 4/16

JT5000SF

GE 30" Built-In Single Convection Wall Oven FEATURES AND BENEFITS True European Convection – Achieve delicious results from a third heating element and fan combination Convection

Self-clean with steam clean option – Clean your oven the way you want Self-clean heavy-duty oven racks – Conveniently clean your oven and racks together

Convection

1 Rack/Multi

r

Glass touch controls – Set temperatures quickly and clean with little effort Halogen interior oven lighting – Easily see how your food is baking Ten-pass bake element – Even baking is assured with heat that covers more surface area Eight-pass broil element – Get full broil coverage and even browning from edge to edge 5.0 cu. ft. oven capacity – Cook more dishes at once Black gloss oven interior – Enjoy a clean and sleek appearance Hidden bake – Make cleanup easy by eliminating hard-to-reach areas Model JT5000SFSS – Stainless steel GUARANTEED FIT Replacing a similar wall oven from GE or another brand? GE wall ovens are guaranteed for an exact fit to make replacement easy Visit geappliances.com for more info

JT5000SFSS

Specification Revised 4/16

23-1/2" min.

PW9000SF GE Profile™ Series 30" Warming Drawer Dimensions and Installation Information (in inches)

Optional Accessories: ZXD30B –1/4” panel kit 23-1/4" capability.

Warming A

23-1/4"

Note: Custom panel will not be flush with adjacent cabinetry drawers and doors. 10-1/2" 10-1/2"

23-1/4" Undercounter Installation: A solid barrier must be installed at least 1” from the lowest point of the bottom of cooktop burner box to the10-1/2" top of the B cutout. Use any solid material such as 1/4”-thick B plywood. Allow at least 1/4” air gap between the barrier and the top of the warming drawer. See B label on top of the warming drawer for approved cooktop models.

Under Oven Installation: Additional clearance between cutouts may be required. Check to be sure that oven supports above the warming drawer location do not obstruct the required interior 23-1/2” depth and 9-1/4” height.

Locate 2 warming drawers perelectrical outlet in adjacent the ID elevations.cabinet 16" from Locate electrical outlet in adjacent cabinet 16" from left side or 42" from right side

9-1/4"

9-1/4"

24" A recommended 9-1/4" from floor 9-1/4" for under 24" countertop recommended installation

23-1/4"

10-1/2"

from floor for under countertop installation

B

Install Install 2x4 or 2x2 2x4anti-tip or 2x2 block 9" anti-tip from floor from2x4 floor to bottom or 2x2 block 9" of block to runners bottomor solid from floor bottom of block

Door handle protrudes 2-3/4” from door face. runners or solid9" 9" bottom Cabinets and drawers on adjacent 45° and 90° 2x4 or 2x2 walls should be placed to avoid interference with(Must Support runners or solid 150 lbs.) bottom2x4 or 2x2 the handle. (Must Support 150to lbs.)bottom of block runners or solid (Must Support 150 lbs.) Installation Information: Before installing, consult bottom installation instructions packed with product for ­current dimensional data. KW Rating 120V

.45

Breaker Size 120V

15 Amps

Dimensions (in inches)

Dimensions (in inches)

Dimensions (in inches) A

27" Drawer

25-1/2"

(Must Support 150 lbs.) A B

A 27" Drawer

26-3/4"

B25-1/2"

28-1/2"

30" Drawer

A

29-3/4" 28-1/2"

A

B 26-3/4"

27" Drawer 25-1/2" 26-3/4" Dimensions (in inches) 28-1/2" 30" Drawer 28-1/2" 30" Drawer

30" Drawer

29-3/4"

B 29-3/4" 29-3/4"

B

27" Drawer 25-1/2" ® For answers to your Monogram® or GE26-3/4" appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000.

30" Drawer

23-1/2" min.

28-1/2"

29-3/4"

Oven cutout

23-1/2" min.

Oven cutout

cabinet 16" from left side or 42" from right side

2x2 or 2x4 2" min. anti-tip block

2" min.

24" recommended from floor for under 24" countertop recommended from floor installation for under

against rear wall 9" from floor 2x2 to or bottom 2x4 Oven 9" ofanti-tip block block Allow 5/8" cutout 2x2 or 2x4 rear 9-1/4" overlapagainst on anti-tip block

Oven cutout

Allow 5/8" 2" min. overlap on all sides

wall 9" from

2" min.

rear all sidesfloor toagainst bottom wall 9" from

9"

Allow 5/8" overlap on Allow 5/8" overlap on all sides

of block floor to bottom

9"

9-1/4"

of block

9-1/4"

all sides

A

countertop installation

1" min. above toekick or A adjust to oven installation height

A

Install 2x4 or 2x2 anti-tip block 9" Install 2x4 or 2x2 from floor anti-tip 9" to bottom of block block 9"

2x4 or 2x2

left side or 42" from right side Under Oven Installation

Locate electrical outlet in adjacent DrawerADimensions cabinet 16" from Locate electrical left side or 42" outlet in adjacent from right side

A

9"

23-1/2" min.

A

1" min. toekick above toekick 1" min. above or adjustortoadjust ovento oven installation installation height height

Undercounter Installation 1-1/2" Cabinet top

Electrical outlet

Install a solid barrierside right 7 below a cooktop Install a solidflush barrier

25"

1" Min.* 9-1/4"

Install 2x4 2x2 wall 9" from rearor cabinet with 7side of floor to bottom ofoutlet block Electrical anti-tip blocktoagainst floor bottom of block cabinet 7" max. rear cabinet wallfrom 9" from 42" max. 7 Electrical out 9 floor 9 to bottom of block 1-1/2"

below a cooktop

1" Min.* 36" Install a solid1"barrier Min.* below a cooktop Countertop 9-1/4" 9-1/4" height

36" Countertop height

Install 2x4 or 2x2

Electrical outlet

1-1/2" right side Installagainst 2x4 or 2x2 flush withanti-tip side of block Cabinet topmax. fromcabinet 7" max. 42" Electrical outlet anti-tip block against 25" wall 9" from cabinet 7"rear max.cabinet

25"

1-1/2" Cabinet top

36" Countertop height

Electrical outlet 42" max. from Electrical Electrical outlet outlet right side 42" max.with fromside of flush

A

A

A Cabinet top Solid barrier

right side

25"9 Solid barrier

Solid barrier

1/4" Air gap

Electrical

Electrical outlet 16" max. outlet 16" max. from left side Install a solid barrier from left side 1/4" Air gap belowElectrical a cooktop

Install a solid barrier below a cooktop

7

outlet 16" max. 23-1/2 min. from left" side

36" 1" Min. * Install a solid barrier 23-1/2 " min. 1/4" Air gap Countertop below a cooktop 9-1/4" 23-1/2" min.

Install a solid barrier height below a cooktop

flush with sid cabinet 7" m

A Listed by Solid barrier Underwriters Laboratories 1/4" Air gap

Specification Revised 8/14

Install a solid barrier below a cooktop

PW9000SF GE Profile™ Series 30" Warming Drawer Features and Benefits • Variable temperature control - Provides a variety of temperatures • Variable humidity control - Customized warming from crisp to moist • Frameless drawer front - Offers a smooth appearance • “On” indicator light - Illuminates when warming drawer is operating • Half rack - Maximizes drawer space • Model PW9000SFSS – Stainless steel

PW9000_PJ7000

Specification Revised 8/14

SP6DS2D7ADA 32" x 23.75" x 23.63" (H x W x D) Commercially approved ADA compliant two-drawer refrigerator in stainless steel for built-in use

Highlights: Commercially approved for use in food service establishments 32 inch height fits under lower ADA compliant counters Flexible design allows built-in or freestanding use

Product Features: ADA Compliant

32 inch height is designed to fit under ADA compliant counters

Commercially approved

ETL-S listed to NSF-7 Standards for use in commercial establishments

Slim undercounter dimensions

Less than 24 inches wide to fit tight spaces

Built-in capable

Make the best use of space by installing your appliance under the counter and flush with other cabinetry

Fully finished cabinet

Allows the unit to be used freestanding

Complete stainless steel construction

Built with solid durability, inside and out

Automatic defrost

Reduced maintenance with auto defrost system

Adjustable thermostat

Dial thermostat for easy temperature management

Spring assisted rollers

Enjoy the gentle gliding motion that helps you open the drawer and keep it firmly closed

SUMMIT APPLIANCE DIVISION, FELIX STORCH, INC. | ISO 9001:2008 Certified 770 Garrison Avenue Bronx, NY 10474 USA TEL 718-893-3900 FAX 844-478-8799

[email protected]

www.summitappliance.com

SP6DS2D7ADA Specifications: Overview Height of Cabinet

32.0" (81 cm)

Width

23.75" (60 cm)

Depth

23.63" (60 cm)

Depth with Handle

24.63" (63 cm)

Depth with door at 90°

40.5" (103 cm)

Capacity

3.1 cu.ft. (88 L)

Defrost Type

Automatic

Door

Stainless Steel

Cabinet

Stainless Steel

US Electrical Safety

ETL

Canadian Electrical Safety

ETL-C

Sanitation

ETL-S

Amps Shipping Weight Parts & Labor Warranty Compressor Warranty

1.3 140.0 lbs. (64 kg) 1 Year 5 Years

Refrigerator Features Thermostat Type Fan Type

Dial Interior and Exterior

Refrigerant Type

R134a

Refrigerant Amount

1.8oz.

High Side PSI

285.0

Low Side PSI

70.0

Level Legs Qty

4

Dimensions Interior Height 1

9.25" (23 cm)

Interior Width 1

19.75" (50 cm)

Compressor Step Height Compressor Step Width Compressor Step Depth

7.0" (18 cm) 19.75" (50 cm) 6.0" (15 cm)

Drawer Dimensions Interior Depth 1

17.75" (45 cm)

Interior Height 2

11.75" (30 cm)

Interior Width 2

19.75" (50 cm)

Interior Depth 2

17.75" (45 cm)

SUMMIT APPLIANCE DIVISION, FELIX STORCH, INC. | ISO 9001:2008 Certified 770 Garrison Avenue Bronx, NY 10474 USA TEL 718-893-3900 FAX 844-478-8799

[email protected]

www.summitappliance.com

GLDT690D/GLDT696D

GE® Stainless Steel Interior Dishwasher with Hidden Controls Dimensions and Installation Information (in inches) Electrical Rating Voltage AC.......................................................... 120 Hertz.................................................................... 60 Total connected load amperage.............   6.7 Calrod® heater watts max....................... 650 For use on adequately wired 120-volt, 15-amp circuit having 2-wire service with a separate ground wire. This appliance must be grounded for safe operation.

For answers to your Monogram,® Cafe™ Series, Profile™ Series or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. Listed by Underwriters Laboratories

As an Energy Star® partner, GE has determined that this product meets the Energy Star guidelines for energy efficiency.

Specification Revised 7/13

350219

GLDT690D/GLDT696D

GE® Stainless Steel Interior Dishwasher with Hidden Controls Features and Benefits • Bright annealed stainless steel interior - Attractive interior provides long-lasting durability • Low profile installation capable - Great for raised sub-floors and 34" countertop heights • Gray racks - Long-lasting, durable racks resist rusting, chipping and peeling • Two utility shelves in upper rack with Stem Safe - Conveniently flip down to handle tall items and protect stemware • 2-digit countdown display with 1-24 hour Delay Start - Wash dishes at your convenience and monitor the progress • Audible end-of-cycle signal - Alert signals when cycle is complete • 5 wash levels - Eliminates the central wash tower to accommodate more items • ADA-compliant - Dishwasher design allows for simple operation and easy access • ENERGY STAR® qualified - Meets or exceeds federal guidelines for energy efficiency for year-round energy and money savings • Model GLDT690DWW – White on white • Model GLDT690DBB – Black on black • Model GLDT696DSS – Stainless steel (shown)

GLDT696TSS As an Energy Star® partner, GE has determined that this product meets the Energy Star guidelines for energy efficiency.

Specification Revised 7/13

350219

JENN-AIR DETAILED PLANNING DIMENSIONS ®

1 of 2

under counter microwave oven with drawer design JMD2124W – 233⁄4" x 153⁄8" x 241⁄2"

PRODUCT DIMENSIONS A A

MODEL # B B

A

E C E G C F G F D D FRONT VIEW

Height of control panel

C

Height of drawer

D

Height of trim

E

M M G G

in

cm

233⁄4

60.4

21⁄2 Back of Cabinet Back of101⁄2 Cabinet

6.2 26.6 5.1

Space between control panel and drawer

1⁄8

0.4

Space between drawer and trim

1⁄4

0.5

Overall height

153⁄8

39.1

H

Recessed width

215⁄8

54.9

I

Width of conduit channel

45⁄8

11.9

J

Depth without drawer

231⁄2

59.7

Depth with drawer

241⁄2

62.4

Depth with drawer fully open

391⁄2

100.5

M

Recessed height

145⁄8

37.1

N

Depth with drawer fully open   Flush receptacle

391⁄2

100.5

44

111.9

241⁄2

62.4

29

73.8

Depth without drawer   Flush receptacle

231⁄2

59.7

  Non-flush receptacle

28

71.1

K L

J J K K L L

JMD2124W

2

G

I I

Overall width

B

F

H H

N N O O P P

  Non-flush receptacle O

Depth with drawer   Flush receptacle   Non-flush Power Supply Locationreceptacle Power Supply Location

P

Top VIEW

N

O

P M

G Back of Cabinet

Side VIEW

Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.

JRC120058A 07/2012

JENN-AIR DETAILED PLANNING DIMENSIONS ®

2 of 2

under counter microwave oven with drawer design JMD2124W – 233⁄4" x 153⁄8" x 241⁄2"

OPENING/CLEARANCE DIMENSIONS MODEL # A C

B

e

B

C

D

A E

D E

in

cm

Width of cutout

221⁄8

56.2

Height of cutout

147⁄8

37.6

Top of cutout to bottom of oven (min.)

2

5.1

Top of cutout to bottom of countertop (min.)

2

5.1

Bottom of cutout to top of cabinet door (min.)

2

5.1

231⁄2

59.7

28

71.1

Depth of cutout (min.)    with flush receptacle    with non-flush receptacle

e

e

e

B A

A

B B D

C

120 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded circuit P is required. A time-delay fuse or dedicated circuit is recommended. Do not use an extension cord.

LOCATION REQUIREMENTS M

D

E

Recommended electrical connection location

N ELECTRICAL REQUIREMENTS O

C

C

A

JMD2124W

G 100 lb (45.4 kg) including Support structure must be able to support Back of microwave oven and contents. Cabinet

G F E

D

FRONT VIEW – installation under single oven

E

SIDE VIEW

H

I

J e

K B

C L D

A

Power Supply Location

FRONT VIEW – installation under C countertop

Back VIEW

C

e

e

A

B A

B D

D

Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.

JRC120058A 07/2012

15” Marvel Low Profile Clear Ice™ Machine ADA Height Model # 30iMAT****

• Produces up to 34 lbs of clear ice in 24 hours and stores up to 30 lbs • Stainless steel ice cutter ensures consistent cube size and shape • Sound-buffering ice deflector greatly reduces cube impact noise • Low profile, ADA height allows for universal installation applications, both commercial and residential • High efficiency, low maintenance condenser design for built-in zero clearance installations • Equipped with cleaning mode • Insulated thermal-efficient cabinet • Frost-free technology ensures you’ll never have to manually defrost the unit • Ice scoop included • Available with or without factory-installed drain pump • Close Door Assist System™ gently and automatically closes door • Height adjustment up to 1” with leveling legs • 4” black adjustable toe kick • 1-year warranty

Storage Capacity Up to 30 lbs of clear ice

Product Dimensions 14 ⅞“ W x 31 ⅛ “ H x 25 ⅝ “D (including handle)

Accessories 16-oz Ice Machine Sanitizer 4-oz Ice Machine Cleaner

Finish/Door Options

Stainless Steel

Black

White

Wood Overlay (Panel Ready)

Ordering Details NO FACTORY-INSTALLED DRAIN PUMP

"A"

"B" "C" 15" Rough-In Dimensions "A"

"B"

"C"

15" (38.1 cm)

**31 3/8" to 32 3/8" (79.1 to 81.6 cm)

24” (61 cm)

Solid Stainless Door, Right Hinge

30iMAT-BS-F-R

Solid Stainless Door, Left Hinge

30iMAT-BS-F-L

Solid Panel Overlay Ready Door, Stainless Handle, Right Hinge

30iMAT-BB-O-R

Solid Panel Overlay Ready Door, Stainless Handle, Left Hinge

30iMAT-BB-O-L

Solid Black Door, Right Hinge

30iMAT-BB-F-R

Solid Black Door, Left Hinge

30iMAT-BB-F-L

Solid White Door, Right Hinge

30iMAT-WW-F-R

Solid White Door, Left Hinge

30iMAT-WW-F-L

WITH FACTORY-INSTALLED DIMENSIONS FOR 30IMAT SOLID OVERLAY DOOR DRAIN PUMP

211/2” (54.6cm)

137/8” (35.3cm)

Solid Stainless Door, Right Hinge

30iMAT-BS-F-R-P

Solid Stainless Door, Left Hinge

30iMAT-BS-F-L-P

Solid Black Door, Right Hinge

30iMAT-BB-F-R-P

Solid Black Door, Left Hinge

30iMAT-BB-F-L-P

Solid White Door, Right Hinge 371/16” (95.4cm) 227/8”* (58.1cm)

147/8” (37.8cm)

30iMAT-WW-FR-P

Solid White Door, Left Hinge

30iMAT-WW-F-L-P

Solid Panel Overlay Ready Door, Stainless Handle, Right Hinge

30iMAT-BB-O-R-P

Solid Panel Overlay Ready CL water supply Door, Stainless Handle, Left Hinge

30iMAT-BB-O-L-P

2” (5.1cm)

311/8” to 321/8” (79.1 to 81.6cm)

No panel installation kit required.

CL water supply

6” (15.2cm) 2” (5.1cm)

3” to 4” (7.6 to 8.8cm)

Width Interior Finish Capacity

ROUGH IN OPENING DIMENSIONS, FOR 30IMAT SOLID OVERLAY DOOR Vacation / Temperature Range NA 14 ¾" White Up to 30lbs of clear ice

Lock Electrical Requirements

120V / 60Hz / 15A

Length of Power Cord

5'

Product Dimensions

Shelf Fronts

NA

Depth to Front of Door

23 ¾"

Other Storage

NA

Depth to Handle

25 ½"

Interior Lighting

NA

Depth with door at 90°

37 1/16"

Shipping Weight

120 lbs

Handle Control Type

Black

Designer

Finishes

NA

Agency Approvals

CSA

ENERGY STAR Certified

NA

14 ¾" W x 31 ⅛" H x 21 ½" D

Classic Hinge

** 313/8” to 323/8” NA (79.7 to 82.2cm)

Sabbath Mode

NA

NA

Hinge

8” (20.3cm)

CL gravity drain

Shelving System

Toe Grill Finish

* To face of door without custom panel

SS, B, W, O

Electrical Requirements: A grounded 115 volt, 15 amp dedicated circuit Finishes Keyis required.

SS = Stainless Steel Power outlet can be located in the back wall behind B = Black the ice machine. 1” to depth for thickness of W = Add White plug, or recess outlet 1” into the wall. Power outlet O = Overlay can also be installed in adjacent cabinetry with a cutout for routing of power cord. Follow all local building codes when installing electrical and the ice

p hinge ange as shown . This space can be adjusted by adjusting the oveand thebottom hinge adapters. op

m)

Overlay Panels

W

from the door, drill the mounting holes from the front, to the recommended diameter of the handle manufacturer. Counter bore the back-side of the panel so the screw heads do not interfere with the surface of the door.

W Top hinge adapter

FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS

Front of overlay H panel Front of is attachedoverlay to the door and cabinet. After the panel is removed from the door, H from the front, to the paneldrill the mounting holes recommended diameter of the handle manufacturer. Counter bore the back-side of the panel so the screw heads do not interfere with the surface of the door.

Material Type

#8 Wood Screw

Hardwood

1/8” (3.2mm) Diameter. Pilot Hole

Softwood

7/64 (2.8mm) Diameter. Pilot Hole Table B

Figure 11 Figure Top11hinge Model adapter

W

Model

30iMT W

145/8” (37.1cm) H

30iMT

145/8” 30iMAT (37.1cm)

145/8” 305/16” (37.1cm) (77.0cm)

30iMAT

145/8” (37.1cm)

2711/16” Table A (70.3cm)

Table A

Hole in hinge adapter

Door H 305/16” (77.0cm) Hole in hinge

Clearance hole through door gasket channel

Overlay panel

2711/16” adapter (70.3cm)

#10 Wood Screw

FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS

Step 5: Drill hinge clearance holes in overlay panel

ved e er nter-

Step 8: Install door gasket

Press the door gasket into the door Make certain the Material Type #8channel. Wood Screw Hole in bottom gasket corners are fully inserted. If applicable insert the key into Hardwood 1/8” (3.2mm) Diameter. Pilot Hole hinge adapter the lock and make certain the lock operates properly. Softwood 7/64 (2.8mm) Diameter. Pilot Hole Figure 12 Step 9: Install the door Door Install the top and bottomTable hingeBadapter bushings back into the hinge adapters that were removed in step 6. Install the door by reversing the procedure from step 2. InstallOverlay the top hinge pin so the screw flush with the top surface of the hinge. If appliStep 6: head Drill ispanel mounting holespanel

Top d adap

Figure 12

n Set the overlay panel on the door front, align the edges, and out- 5: Drill ishinge attached to the door and cabinet. After the panel isnot removed tep clearance holes in overlay clamp together. Clamp the panel firmly butpanel be careful to Material Type #8 Wood Screw Back of door from the drill the mounting from front, to the Door t the overlay panel ondoor, the door front, alignMark theholes edges, and damage the door or the panel. center of the hinge adapter recommended diameter of the manufacturer. Counter 1/8” (3.2mm) amp together. Clamp the panel firmly but behandle careful not to 12.) Remove hole on wood panel, top and bottom. (See Figure Step 6: Hardwood Drill panel mounting holesDiameter. Pilot Hole boreorpanel the of the panel so the screw heads clearance do not inter- Re-clamp Softwood amage the door theback-side panel. Mark center hinge adapter wood from door and drillof 5/16” (8mm) diameter the panel to the door step 5Diameter. and drill the 7/64 per (2.8mm) Pilotscrew Hole Overlay fere with the surface of (See the door. Figure 13door. Select ole on woodholes panel, top and bottom. Figure 12.) deep. Remove into the overlay panels 3/4” (20mm) These will be pilot holes for attaching the overlay panel to the gain panel oodby panel from door holes and drill clearance clearance for 5/16” the (8mm) top anddiameter bottom hinge pins. the size of the hole from TableTable B. BeBcareful not to drill the pilot ket oles into the overlay panels 3/4” (20mm) deep. These will be holes through the overlay panel, (1/2” (12.7mm) deep for 3/4” earance holes the top and bottom hinge pins. Thisfor is also a convenient time to locate and drill thePANEL holes for INSTALLATION (19mm) and 5/8” INSTRUCTIONS (15.7mm) panels ). FULL OVERLAY Top hinge your handle. Most often the handle is to match that of the surTop hinge Top hinge pin Hole in bottom adapter Step 7: Secure overlay panel to the door. his is also a convenient time to locate and drill the holes for rounding cabinetry. If your handle attaches from the back-side el to Clearance hole through hinge adapter With the #10 wood screws provided, fasten the overlay panel to ur handle. of Most thepanel, handle is to the match that of holes the surthe often custom locate mounting while the panel door gasket channel Topdoor. door hinge Hole in hinge the (See Figure 13). 14 is attached to the and cabinet. After the panel is removed unding cabinetry. IfFigure your handle from the back-side 12 doorattaches adapter Material Type #8 Wood Screw thelocate door, the drillmounting the mounting the front, to the the customfrom panel, holesholes whilefrom theadapter panel Step 8: Install door gasket recommended diameter of the handle manufacturer. Counter Hardwood 1/8”door (3.2mm) Diameter. Hole Top hinge adapter Press the gasket into the channel. Make Pilot certain the #10door Wood Screw bore the back-side of the panel so the screw heads do not interbushing Softwood 7/64 (2.8mm) Diameter. gasket corners are fully inserted. If applicable insertPilot theHole key into fere with the surface of the door. the lock and make certain the lock operates properly. Step 6: Drill panel mounting holes Table B Re-clamp the panel to the door per step 5 and drill the screw Step 9: Install the door pilot holes for attaching the overlay panel to the door. Select Bottom door Install the top and bottom hinge adapter bushings back into the the size of the hole Top from hingeTable B. Be careful not to drill the pilot hinge adapters adapter that were removed in step 6. Install the door by hinge holes through the overlay panel, (1/2” (12.7mm) deep for 3/4” Back of door adapter Door reversing the procedure from step 2. Install the top hinge pin so Clearance hole through (19mm) and 5/8” (15.7mm) panels ). the screw head is flush with the top surface of the hinge. If applidoor gasket channel Hole in hinge cable insert key into lock and verify the lock cam works properly Step 7: Secure overlay panel to the door. Overlay INSTALLATION INSTRUCTIONS 13 adapter with thehinge catch bracket on the front of theFigure ice machine cabinet. With the #10 wood screws provided, fasten panel the overlay panel to Bottom the door. (See Figure 13).

Top h

Hole in bottom hinge adapter

adapter bushing #10 Wood Screw Bottom hinge Top hinge pin cam

Top door hinge Bottom hinge pin adapter Back of door comprehensive TopFor hinge adapter installation instructions, please visit www.marvelrefrigeration.com bushing Figure 14 Figure 13

Top hinge

Bottom hinge

Top h bushi

Botto hinge

Botto adap

Botto cam

Botto

15

GFC535V

GE Appliances 1/2 Horsepower Continuous-Feed Disposer DISPOSALL® FOOD WASTE DISPOSER DIMENSIONS (IN INCHES)

ers-Continuous Feed INLET/OUTLET DIAMETERS

7 3/4

6 15/16

Dishwasher inlet diameter (in.)

1

Drain outlet diameter (in.)

1-1/2

POWER/RATINGS Power Connection

Line Cord

Volts/Hertz/Amps

120 V/60 Hz/4.5 A

13 7/16

5 3/8

Listed by Underwriters Laboratories

For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.

Specification Revised 5/16

GFC535V

GE Appliances 1/2 Horsepower Continuous-Feed Disposer FEATURES AND BENEFITS 1/2 Horsepower Motor Extra-Large-Capacity, Continuous-Feed Disposer Over 2800 RPM Grinding Action* Stainless Steel Jam-Resistant, Dual-Swivel Impellers EZ Mount installation Line Cord Power Connection, length = 35" Sound Reduction Technology ColdRolled Carbon Steel Armature Shaft Material SplashGuard Wall Switch with Sink Stopper Manual Reset Overload Protector Dishwasher Drain Connector Stainless Steel Sink Flange Stainless Steel Turntable 2 Level Precutter Model GFC535V *Based on RPM testing of cleared GE and competitive models

For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.

GFC530T_GFC535T GFC530V_GFC535V

Listed by Underwriters Laboratories

Specification Revised 5/16

Needs to be stainless steel. How about SCR600BLBIHVADA

SCR600LBIADA 32" x 23.63" x 23.5" (H x W x D) ADA compliant commercially listed built-in undercounter glass door all-refrigerator with white cabinet and front lock

Highlights: Commercially approved for use in food service establishments 32 inch height fits under lower ADA compliant counters Flexible design allows built-in or freestanding use in 24" spaces

Product Features: Commercially approved

ETL-S Listed and CalCode Compliant

ADA Compliant

32 inch height is designed to fit under ADA compliant counters

Factory installed lock

Keyed lock for a secure interior

Built-in capable

Make the best use of space by installing your appliance under the counter and flush with other cabinetry

Fully finished white cabinet

Allows the unit to be used freestanding

Double pane tempered glass door

Heat resistant design provides clear view of stored products

Reversible door

Keep placement options flexible with a reversible door swing that is easy to switch when your arrangement changes

Automatic defrost

Reduced user maintenance with automatic defrost

One piece interior liner

Simple cleanup with a seamless liner that won't hold a mess in hidden crevices

SUMMIT APPLIANCE DIVISION, FELIX STORCH, INC. | ISO 9001:2008 Certified 770 Garrison Avenue Bronx, NY 10474 USA TEL 718-893-3900 FAX 844-478-8799

[email protected]

www.summitappliance.com

SCR600LBIADA Specifications: Overview Height of Cabinet

32.0" (81 cm)

Height to Hinge Cap

32.38" (82 cm)

Width

23.63" (60 cm)

Depth

23.5" (60 cm)

Depth with Handle

25.5" (65 cm)

Depth with door at 90° Capacity Defrost Type

White

US Electrical Safety

UL

Canadian Electrical Safety

ULC

Shipping Weight Parts & Labor Warranty Compressor Warranty

5.0" (13 cm)

Automatic

Cabinet

Voltage/Frequency

Compressor Step Depth

5.5 cu.ft. (156 L)

Glass

Amps

20.75" (53 cm)

46.0" (117 cm)

Door

Sanitation

Compressor Step Width

ETL-S 1.0 115 V AC/60 Hz 115.0 lbs. (52 kg) 1 Year 5 Years

Refrigerator Features Door Swing

RHD

Reversible

Yes

Shelf Type

Wire

Shelf Qty

4

Adjustable Shelves

Yes

Thermostat Type

Dial

Fan Type

Exterior

Refrigerant Type

R134a

Refrigerant Amount

1.8oz.

High Side PSI

285.0

Low Side PSI

70.0

Level Legs Qty Interior Light

2 Yes

Dimensions Interior Height

26.0" (66 cm)

Interior Width

20.75" (53 cm)

Interior Depth

17.5" (44 cm)

Compressor Step Height

6.0" (15 cm)

SUMMIT APPLIANCE DIVISION, FELIX STORCH, INC. | ISO 9001:2008 Certified 770 Garrison Avenue Bronx, NY 10474 USA TEL 718-893-3900 FAX 844-478-8799

[email protected]

www.summitappliance.com

GLDA690FWW/GLDA690FBB/GLDA696FSS GE® Stainless Steel Interior Dishwasher with Front Controls Dimensions and Installation Information (in inches) Electrical Rating Voltage AC............................................................120 Hertz......................................................................... 60 Total connected load amperage................. 6.7 Calrod® heater watts max............................650

32-1/2" to 34-3/4" 34-1/2" 1/4" Underside Underside ofof Countertop Countertop to Floor to Floor

For use on adequately wired 120-volt, 15-amp circuit having 2-wire service with a separate ground wire. This appliance must be grounded for safe operation. Note: The rough cabinet opening must be at least 24" deep, 24" wide and approximately 34-1/2" high from floor to underside of the countertop. Dishwasher must not be installed more than 10 feet from sink for proper drainage. All plumbing and electrical work must be in accordance with local codes. The power cord and connections must comply with the National Electrical Code Section 422 and/or local codes and ordinances. The cord must be no longer than 6 ft. from the junction box to the receptacle. Installation Information: Before installing, consult installation instructions packed with product for c­ urrent dimensional data.

For answers to your Monogram,® Cafe™ Series, Profile™ Series or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000.

24" MAX.

This Wall Area must be Free of Pipes or wires 5"

24" Min.

Plumbing and Electric Service Must Enter Inside This Area

Figure A

24

4"

5"

24" Min.

Cabinets Square and Plumb

Floor MUST be Even With Room Floor

• The rough cabinet opening must be at least 24" deep, 24" wide and approximately 32-1/2" to 34-3/4" high from floor to underside of the countertop.

22

25-5/8 32-7/20" MIN. adj. to 34-1/2" 20-1/2 4" (Adjustable) 4 Listed by Underwriters Laboratories

Specification Created 7/13

350241

GLDA690FWW/GLDA690FBB/GLDA696FSS GE® Stainless Steel Interior Dishwasher with Front Controls Features and Benefits • ADA-compliant for height - Designed for easy access and operation • Bright annealed stainless steel interior - A lustrous finish and lasting beauty that resists stains and corrosion • 9 electronic touchpads - Provide a smooth, easy-to-use, easy-to-clean surface • 2-digit countdown display with 2/4/8-hour Delay Start - Signals remaining cycle time, makes it easier than ever to wash dishes at any hour, taking advantage of reduced energy rates or washing dishes even when the family is asleep • Electronic controls with 4 cycles/4 options - Make it easy to select a wide range of wash cycles • Two utility shelves in tiered upper rack with 1 Stem Safe - Adjust easily, provide room to stack items and a secure place to wash delicate stemware • Deluxe lower rack - Curved tines accommodate stoneware, large plates or broiler pans • Pots and Pans Cycle - Scours off baked-on food with a wall of water • Heated dry option - Circulates warm air to quickly and gently dry dishes • Model GLDA696FSS - Stainless steel (shown) • Model GLDA696FWW - White on white • Model GLDA696FBB - Black on black

GLDA696MSS

Specification Created 7/13

350241

G Needs to be changed out to match what is being provided in the units.

PZS22MMK/MSK

GE Profile™ Series 22.1 Cu. Ft. Counter-Depth Side-by-Side Refrigerator DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

69-7/8

Height to top of hinge (in.) B

H

69-1/4

Height to top of case (in.) C

G

69

Case depth without door (in.) D

24-1/8

Case depth less door handle (in.) E

28-1/2

Case depth with door handle (in.) F

30-3/4

Depth with fresh food door open 90° (in.) G

46-1/4

Width (in.) H

35-3/4

Width with door open 90° inc. door handle (in.) I

43-1/4

C

D

AA BB C

I H

D

E

E

F F

G

1/8

Top (in.)

1

Back (in.)

2

Height to top of door (in.) A

69-7/8

Height to top of hinge (in.) B

69-1/4

For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.

Height to top of case (in.) B

Height to top of case (in.) C

67-3/8 66-7/8 69

Case depth without door (in.) C Case depth without door (in.) D

26-5/6

Case depth with door handle (in.)(in.) EF Case depth with door handle

32-1/2 30-3/4

OVERALL DIMENSIONS

OVERALL DIMENSIONS

Height to top of hinge (in.) A

24-1/8

DepthDepth with fresh foodfood doordoor open 90˚90° (in.) FG with fresh open (in.)

56-3/4 46-1/4

Width Width (in.) G(in.) H

28 35-3/4

with door door handle(in.) (in.)H I Width Width with door openopen 90˚ 90° withinc. door handle

30-5/8 43-1/4 Listed by

Case depth less door handle (in.)(in.) DE Case depth less door handle

Each side (in.)

Each side (in.) AIR

Each side (in.) AIR

TOP VIEW

Height to top of door (in.) A

AIR CLEARANCES

OVERALL DIMENSIONS

FRONT VIEW

Top (in.)

Top (in.) Back (in.) Back (in.)

30-1/2 28-1/2

1/8 Underwriters

3/4 Laboratories

1

21

2 Specification Revised 4/16

24" CABINET

3/4" AIRSPACE (1/2" GAP + 1/4" WALL PLATES)

25" COUNTER TOP

PZS22MMK/MSK

24" CABINET

3/4" AIRSPACE (1/2" GAP + 1/4" WALL PLATES)

25" COUNTER TOP

GE Profile™ Series 22.1 Cu. Ft. Counter-Depth Side-by-Side Refrigerator DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

TRIM

INSTALLATION TIPS TO MAXIMIZE THE BUILT-IN LOOK All wall/floor molding should be removed prior to installation.

12" SOFFIT

Water recess on rear wall recommended to prevent water line damage. 48" minimum length, 1/4" diameter water line tubing recommended.

8' CEILING

13" to 14" CABINET

When possible, recess both copper water line and electrical outlet. (See local codes) Front and rear leveling legs are adjustable for the built-in look. (See owner’s manual) WATER

24" CABINET

FOR 24 CUBIC FOOT MODELS

WATER

ELECTRICAL

3/4" AIRSPACE (1/2" GAP + 1/4" WALL PLATES) 25" COUNTER TOP

Fig 2A eps

24" CABINET

ELECTRICAL

3/4" AIRSPACE (1/2" GAP70"* + 1/4" 23 CU. FT. MODELS WALL PLATES) 25" 72-1/2"* COUNTER TOP 25 CU. FT. MODELS

TRIM

24-1/2" 36-1/8"

*The rough-in dimensions of 70" for 23 cu. ft. models and 72-1/2" for 25 cu. ft. models are minimum and measured from the finished floor to top of opening *The rough-in dimensions of 70" for 23 cu. ft. models and 72-1/2" for 25 cu. ft. (or the underside of the overhead cabinets). For Models with Trim Kit: If frameless style cabinets are planned for above the refrigerator, you may need models are minimum and measured from the finished floor to top of opening to consider adding a maximum of 1/4" (70-1/4") to height of opening for 23 cu. ft. models and 1/8" (72-5/8") for 25 cu. ft. models to allow for additional clearance between the cabinet doors and the top of refrigerator trim when the cabinet doors are in open position. (or the underside of the overhead cabinets). For Models with Trim Kit: If frameless style cabinets are planned for above the refridgerator, you may need to consider adding a maximum of 1/4" (70-1/4") to height of opening for 23 cu. ft. models and 1/8" (72-5/8") for 25 cu. ft. models to allow additional Listed by clearance between cabinet doors and top of refridgerator trim when cabinet Underwriters doors are in open position. Laboratories † Model PSDW3YGX is 71-3/4". For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000. Specification Revised 4/16

Collar Trim In. w/ceiling

PZS22MMK/MSK

GE Profile™ Series 22.1 Cu. Ft. Counter-Depth Side-by-Side Refrigerator FEATURES AND BENEFITS

Counter-depth design – Offers a built-in look by fitting nearly flush with surrounding cabinetry LED Lighting – Illuminates the fresh food compartment, vegetable drawer and climate-controlled drawers to spotlight food without compromising space Quick Ice setting – Creates ice up to 50% faster than normal settings Turbo Cool setting – Restores proper temperature to the refrigerator after frequent door openings Quick Space shelf – Quickly slides out of the way to make room for tall items Advanced water filtration uses MWF replacement filter – Reduces trace pharmaceuticals from water and ice* (* Removes 98% of ibuprofen, atenolol, fluoxetine, progesterone and trimethoprim. These pharmaceuticals are not necessarily in all users’ water) Adjustable slide-out, spillproof glass shelves – Raised edges help contain spills and make cleanup quick and easy Adjustable Clear Look door bins – Offer ideal space for large containers in the door and free up valuable shelf space Adjustable-humidity drawers – Controls help food stay fresh Glass freezer shelves – Enjoy a high-end appearance with secure storage for a variety of items Model PZS22MMKES – Slate Model PZS22MSKSS – Stainless Steel

PSE28KSH

UFAS COMPLIANT

Specification Revised 4/16

PEM31SF/EF

24-7/8" ± 1/8"

GE Profile™ Series 1.1 Cu. Ft. Countertop Microwave Oven A

Dimensions and Installation Information (in inches) W x H x D

15" ± 1/8"

C

Exterior Dimensions* (in inches) 24 x 12-1/8 x 12-7/8

*Height includes feet. Depth does not include handle and excludes receptacle plug, + 1/2"-3/4". Optional Accessory Trim Kits for GE Microwave Ovens For a custom built-in appearance, these kits allows built-in installation of the countertop microwave oven into a wall or cabinet alone, and is U. L. approved for installation over a GE single electric wall oven. These kits should not be installed over a gas wall oven. Accessory trim kit

"Z"

Max height

Trim kit

27" Deluxe

26-7/8"

16-1/2"

JX827SFSS/EFES

30" Deluxe

29-7/8"

16-1/2"

JX830SFSS/EFES

Installation Information: This information is not intended to be used for installing unit described. Before installing, consult installation instructions packed with product for current dimensional data. Note: Undercabinet Installation Install countertop microwave ovens in just a few easy steps with the mounting template, which provides all the necessary measurements. Installation may vary depending on cabinets. These microwave ovens can be installed on practically any wood or metal cabinets. Note: 120V, 60-cycle, grounded power receptacle location optional on back within cabinet opening.

B

16-1/2"

Trim Kit

18" MIN. receptacle in cabinet 16" MIN. receptacle outside cabinet

Bra

cke t 36" MIN.*

Z

Cabinet overlap requirements 30" A - Overlap of trim kit over top of cabinet 3/4" B - Overlap of trim kit over bottom of cabinet 5/8" C - Overlap of trim kit over sides of cabinet 2-1/2"

*For ADA compliance, the microwave must be installed no higher than 37-7/8".

Accessory Trim Kits JX830 JX827

Note: Allow an additional inch of clearance beyond trim frame on all sides

Z 29-7/8" 26-7/8"

Not to be used over a thermal oven. Undercabinet mounting kit Pub. No. JXA019K for Spacemaker II microwave oven models available at additional cost.

For answers to your Monogram,® Cafe™ Series or Profile™ Series appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000.

27" 3/4" 5/8" 1"

Listed by Underwriters Laboratories

Specification 2/15 240381 Specification Revised 10/13 Revised

PEM31SF/EF GE Profile™ Series 1.1 Cu. Ft. Countertop Microwave Oven Features and Benefits • 1.1 cu. ft. capacity - 800 Watts (IEC-705 test procedure) • Sensor cooking controls - Automatically adjusts time and power • Optional built-in trim kit - Custom appearance and built-in convenience • Optional hanging kit - Frees up counter space • Weight and time defrost - Simply enter the weight of the food, and the oven automatically sets the optimal defrosting time and power level or set your desired time or defrosting • Turntable on/off - Controls turntable operation • Control lockout - Helps prevent accidental activation • Add 30 seconds - Add 30 seconds of microwave cooking time • Kitchen timer - Minute timer helps keep you on track • Timer on/off - Minute timer helps keep you on track • Model PEM31SFSS – Stainless steel • Model PEM31EFES – Slate

PEM3115SF

Listed by Underwriters Laboratories

Specification 2/15 240381 Specification Revised 10/13 Revised