General Product & Quality Specification
DATE: 18/08/2014 VERSION NUMBER: 09
General Product & Quality Specification Flush Veneer and Durador Doors Introduction: Veneered flush\Veneer Match doors are designed for internal use only, and must not be installed in damp conditions. Door faces are factory lacquer finished, enhancing real wood veneers laid ‘edge to edge’ or Veneer Match which uses natural veneers that are dyed & processed to obtain a consistent grain & colour match across the range both ranges are over factory applied solid timber lippings to both vertical edges. Edges require site decoration. The door must be fully sealed on all edges, especially on the top and bottom. Environmental Certification: Doors are manufactured under the formally audited Environmental Standard BS EN ISO 14001. All materials used are from known managed sources, including some formally certified components. Dimensional tolerances apply as follows:
Width Length Thickness Squareness Twist Bow Cup Local Flatness
Tolerance EN1529 +/- 1.5mm +/- 1.5mm +/- 1.0mm 1.5mm Tolerance EN1530 8mm 8mm 4mm 0.4mm
Measurement Method EN 951 EN 951 EN 951 EN 951 EN 952 EN 952 EN 952 EN 952
Quality: Manufacture is controlled against a formal quality management system, -- ISO9001
At supply, door faces and edges will be visibly defect free, when viewed from 2 meters distance. The moisture content of timber components is critically controlled in line with the industry norm, based on BS EN 942. Veneered flush are selected as log run commercial quality. Door faces will be appropriate veneer as advertised, but no specific matching is committed or intended. Edge lippings are of hardwood to compliment the face veneer. Details of applicable product warranties, including qualifying terms and conditions, are available from the current Premdor Range Guide or website. Alternatively contact Premdor’s Technical or Sales Team for specific guidance. Packaging and Product Identification: Doors are clear plastic wrapped for surface protection, and a Product Code or ID is ink marked on the door end, together with lock side indicator if relevant. Fire doors carry a uniquely numbered identification label applied to the top door edge indicating compliance with type testing under BS 476 Part 22 and also BWF / CERTIFIRE accreditation. This label should not be removed, even after installation. Standard Veneer Options As standard the following veneer species are available: Ash, American Maple, American White Oak, Anegre, Koto, American Black Walnut, Sapele and Steamed Beech. Durador is faced with Gaboon/Okoume or Veneer match (quarter cut). Glazed doors: Factory glazed doors incorporate toughened safety glass to the requirements of BS EN 12600. Panes are discreetly marked accordingly, typically at a corner point of the glass. Glass is suitably bedded and beads are securely fixed. Apertures must not be added to fire doors retrospectively except under specific Premdor approval and BWF / CERTIFIRE compliance. Constructional specification: For a general drawing of the standard range of optional core constructions, and door weights, see Annex A, or contact Premdor for more information.
Every effort has been made to ensure the accuracy of this information. In the interest of continuing design development however we reserve the right to modify specifications without prior notice and without incurring any obligation.
GENERAL PRODUCT & QUALITY SPECIFICATION STANDARD CORE VENEERED DOOR
Assembly Components (Size pre-trim) Perimeter framing (Whitewood*) Lock block one side (Particleboard)
**28 x 28mm (35mm Imperial Doors) **28 x 33mm (40mm Metric Doors) 65 x 28mm (35mm Imperial Doors) 65 x 33mm (40mm Metric Doors)
*Chipboard stile framing utilized at our option. **Size subject to manufacturing trim, after door assembly. Lock block positioned one side, central within door height (360mm long) 6mm Hardwood lipping to both long edges Typical door weight 11kgs (762 x 1981) Maximum edge trim, Stiles (Each) 3mm, Top and Bottom 5mm
GENERAL PRODUCT & QUALITY SPECIFICATION VENEERED FD30 FRAMED FIRESHIELD DOOR
Assembly Components (Size pre-trim) Perimeter framing (Whitewood)
FD30
*38 x 38mm (44mm Doors)
*Size subject to manufacturing trim, after door assembly. Lock fixing position – direct into core 6mm Hardwood lipping to both long edges Typical door weight 32kgs (762 x 1981) Maximum from vertical/stile edges 3mm. Bottom trim is 5mm, the CERTIFIRE label must not be removed from the top edge, so no Top trimming is allowed.
GENERAL PRODUCT & QUALITY SPECIFICATION VENEERED FD30 PremCOR FIRESHIELD DOOR
FD30
Assembly Components (Size pre-trim)
*Size subject to manufacturing trim, after door assembly. Lock fixing position – direct into core 6mm Hardwood lipping to both long edges Typical door weight 34kgs (762 x 1981) Edge Trim: Maximum from vertical/stile edges 3mm. Bottom edge is unrestricted; the CERTIFIRE label must not be removed from the top edge, so no Top trimming is allowed.
GENERAL PRODUCT & QUALITY SPECIFICATION VENEERED FD30 TUBECORE FIRESHIELD DOOR
FD30
Assembly Components (Size pre-trim) Perimeter framing (Whitewood) *38 x 38mm (44mm Doors) *Size subject to manufacturing trim, after door assembly. Lock fixing position – direct into core (which has narrow tubes to aid lock/latch fixing) 6mm Hardwood lipping to both long edges Typical door weight 34kgs (762 x 1981) Maximum edge trim, Stiles (Each) 3mm, Bottom 5mm, the CERTIFIRE label must not be removed from the top edge, so Top trimming is not allowed.
GENERAL PRODUCT & QUALITY SPECIFICATION FD60 FIREMASTER VENEERED DOOR
FD60
Lock fixing position – direct into core 6mm Hardwood lipping to both long edges Typical door weight 53kgs (762 x 1981) Edge Trim: Maximum from vertical/stile edges 3mm.Bottom edge is unrestricted; the CERTIFIRE label must not be removed from the top edge, so no Top trimming is allowed.
GENERAL PRODUCT & QUALITY SPECIFICATION FIRESHIELD SOUNDSURE VENEERED DOOR
FD30
Lock fixing position – direct into core 19mm Hardwood lipping to both long edges Typical door weight 53kgs (762 x 1981) Edge Trim: Maximum from vertical/stile edges 3mm. Bottom edge is unrestricted; the CERTIFIRE label must not be removed from the top edge, so no Top trimming is allowed.
General Product & Quality Specification Flush Veneer and Durador Doors Introduction: Veneered flush\Veneer Match doors are designed for internal use only, and must not be installed in damp conditions. Door faces are factory lacquer finished, enhancing real wood veneers laid ‘edge to edge’ or Veneer Match which uses natural veneers that are dyed & processed to obtain a consistent grain & colour match across the range both ranges are over factory applied solid timber lippings to both vertical edges. Edges require site decoration. The door must be fully sealed on all edges, especially on the top and bottom. Environmental Certification: Doors are manufactured under the formally audited Environmental Standard BS EN ISO 14001. All materials used are from known managed sources, including some formally certified components. Dimensional tolerances apply as follows:
Width Length Thickness Squareness Twist Bow Cup Local Flatness
Tolerance EN1529 +/- 1.5mm +/- 1.5mm +/- 1.0mm 1.5mm Tolerance EN1530 8mm 8mm 4mm 0.4mm
Measurement Method EN 951 EN 951 EN 951 EN 951 EN 952 EN 952 EN 952 EN 952
Quality: Manufacture is controlled against a formal quality management system, -- ISO9001
At supply, door faces and edges will be visibly defect free, when viewed from 2 meters distance. The moisture content of timber components is critically controlled in line with the industry norm, based on BS EN 942. Veneered flush are selected as log run commercial quality. Door faces will be appropriate veneer as advertised, but no specific matching is committed or intended. Edge lippings are of hardwood to compliment the face veneer. Details of applicable product warranties, including qualifying terms and conditions, are available from the current Premdor Range Guide or website. Alternatively contact Premdor’s Technical or Sales Team for specific guidance. Packaging and Product Identification: Doors are clear plastic wrapped for surface protection, and a Product Code or ID is ink marked on the door end, together with lock side indicator if relevant. Fire doors carry a uniquely numbered identification label applied to the top door edge indicating compliance with type testing under BS 476 Part 22 and also BWF / CERTIFIRE accreditation. This label should not be removed, even after installation. Standard Veneer Options As standard the following veneer species are available: Ash, American Maple, American White Oak, Anegre, Koto, American Black Walnut, Sapele and Steamed Beech. Durador is faced with Gaboon/Okoume or Veneer match (quarter cut). Glazed doors: Factory glazed doors incorporate toughened safety glass to the requirements of BS EN 12600. Panes are discreetly marked accordingly, typically at a corner point of the glass. Glass is suitably bedded and beads are securely fixed. Apertures must not be added to fire doors retrospectively except under specific Premdor approval and BWF / CERTIFIRE compliance. Constructional specification: For a general drawing of the standard range of optional core constructions, and door weights, see Annex A, or contact Premdor for more information.
Every effort has been made to ensure the accuracy of this information. In the interest of continuing design development however we reserve the right to modify specifications without prior notice and without incurring any obligation.
GENERAL PRODUCT & QUALITY SPECIFICATION STANDARD CORE VENEERED DOOR
Assembly Components (Size pre-trim) Perimeter framing (Whitewood*) Lock block one side (Particleboard)
**28 x 28mm (35mm Imperial Doors) **28 x 33mm (40mm Metric Doors) 65 x 28mm (35mm Imperial Doors) 65 x 33mm (40mm Metric Doors)
*Chipboard stile framing utilized at our option. **Size subject to manufacturing trim, after door assembly. Lock block positioned one side, central within door height (360mm long) 6mm Hardwood lipping to both long edges Typical door weight 11kgs (762 x 1981) Maximum edge trim, Stiles (Each) 3mm, Top and Bottom 5mm
GENERAL PRODUCT & QUALITY SPECIFICATION VENEERED FD30 FRAMED FIRESHIELD DOOR
Assembly Components (Size pre-trim) Perimeter framing (Whitewood)
FD30
*38 x 38mm (44mm Doors)
*Size subject to manufacturing trim, after door assembly. Lock fixing position – direct into core 6mm Hardwood lipping to both long edges Typical door weight 32kgs (762 x 1981) Maximum from vertical/stile edges 3mm. Bottom trim is 5mm, the CERTIFIRE label must not be removed from the top edge, so no Top trimming is allowed.
GENERAL PRODUCT & QUALITY SPECIFICATION VENEERED FD30 PremCOR FIRESHIELD DOOR
FD30
Assembly Components (Size pre-trim)
*Size subject to manufacturing trim, after door assembly. Lock fixing position – direct into core 6mm Hardwood lipping to both long edges Typical door weight 34kgs (762 x 1981) Edge Trim: Maximum from vertical/stile edges 3mm. Bottom edge is unrestricted; the CERTIFIRE label must not be removed from the top edge, so no Top trimming is allowed.
GENERAL PRODUCT & QUALITY SPECIFICATION VENEERED FD30 TUBECORE FIRESHIELD DOOR
FD30
Assembly Components (Size pre-trim) Perimeter framing (Whitewood) *38 x 38mm (44mm Doors) *Size subject to manufacturing trim, after door assembly. Lock fixing position – direct into core (which has narrow tubes to aid lock/latch fixing) 6mm Hardwood lipping to both long edges Typical door weight 34kgs (762 x 1981) Maximum edge trim, Stiles (Each) 3mm, Bottom 5mm, the CERTIFIRE label must not be removed from the top edge, so Top trimming is not allowed.
GENERAL PRODUCT & QUALITY SPECIFICATION FD60 FIREMASTER VENEERED DOOR
FD60
Lock fixing position – direct into core 6mm Hardwood lipping to both long edges Typical door weight 53kgs (762 x 1981) Edge Trim: Maximum from vertical/stile edges 3mm.Bottom edge is unrestricted; the CERTIFIRE label must not be removed from the top edge, so no Top trimming is allowed.
GENERAL PRODUCT & QUALITY SPECIFICATION FIRESHIELD SOUNDSURE VENEERED DOOR
FD30
Lock fixing position – direct into core 19mm Hardwood lipping to both long edges Typical door weight 53kgs (762 x 1981) Edge Trim: Maximum from vertical/stile edges 3mm. Bottom edge is unrestricted; the CERTIFIRE label must not be removed from the top edge, so no Top trimming is allowed.
