guides & slides
GUIDES & SLIDES
q Fig. 439: Structural "H" Slide Assembly q Fig. 439A: Structural "H"
Pipe Slide Assembly, Complete
Size Range: 6 " through 36" PTFE Pipe Slide Assembly – "H" Type Material: Carbon steel “H” section, PTFE bonded slide plates and carbon steel base. Finish: q Plain, q Painted or q Hot-Dip Galvanized (Welded after Galvanizing and Cold Spray Touched-up) Service: A heavy duty slide support where horizontal movement resulting from expansion and contraction takes place and where a low coefficient of friction is desired. Structural "H" Approvals: Complies with Federal Specification A-A-1192A (Type 35), ANSI/MSS SP-69 and MSS SP-58 (Type 35). Maximum Load: As indicated at 70° F see page 135 for rating factor at higher temperatures. Mounting Plate Maximum Temperature: 750° F Temperature Range at PTFE: -20° F to 400° F Features: • No lubrication required. PTFE Slides • Allows up to 4" of insulation. • Allows up to 10” travel standard. • Weld in place design. Available Options: • Increased travels. PTFE Slide Plate Base • Increased “H” Section heights. • Clamps, Fig. 212 or Fig. 432. • Base plate with mounting holes. The bolt spacing for the bolted base plates is equal to the “W” dimention minus 1 1⁄2" and the “BL” Note: In the PH-92 and PH-92R Catalogs: dimention minus 1 1⁄2" for all pipe sizes and the hole diameter is The Fig. 439 (slide “H” section only) formerly referred to as 9⁄16" for all sizes. Fig. 437. The Fig. 439 (slide base plate) formerly referred to as Ordering: S pecify figure number, type, name, finish and any other Fig. 438 (slide base plate). option desired. The acceptability of galvanized coatings at temperatures Notes: T ypes 1, 2, and 3 provide for longitudinal movement only. Types 4 above 450°F is at the discretion of the end user. and 5 provide for both longitudinal and transverse movement of piping.
FIG. 439: DIMENSIONS (IN) • LOADS (LBS) Pipe Size
FIELD WELD PIPE TO FIG 439
D B
PTFE SLIDE PLATES
6 8 10 12 14 16 18 20 24 30 36
1&4
B
D*
Type
Type
2&5
3
5
51⁄4
55⁄16
51⁄8
53⁄8
57⁄16
51⁄4 61⁄4 67⁄16
51⁄2 65⁄8 613⁄16
59⁄16 611⁄16 63⁄4
Max Load
1&4
2&5
3
73⁄4 83⁄4 95⁄8 103⁄4 107⁄8 121⁄8 125⁄8 133⁄4 155⁄8 195⁄8 23
8 9 97⁄8 11 111⁄8 123⁄8 127⁄8 14 157⁄8 197⁄8 231⁄4
8 9 915⁄16 111⁄16 113⁄16 127⁄16 1215⁄16 141⁄16 1515⁄16 201⁄16 237⁄16
Down
Side Up Type Type 3 2, 3, 5
12,000 3,000
1,200
16,000 4,000
1,600
24,000 6,000
2,400
* With clamps; add material thickness of a Fig. 212 for bolted bases add 5⁄16" to height “H” dimension. ** With the Figure 432 special clamp, add the material thickness of Figure 432.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved q Approved as noted q Not approved
Engineer:
Remarks:
Project: Address:
Submittal Date: Notes 1: Notes 2: PH-1.15
GUIDES & SLIDES
Fig. 439
Structural “H” Slide Assembly, Complete BOLTED: DIMENSIONS (IN)
WELDED: DIMENSIONS (IN) Pipe Size
1
6 8 10 12 14 16 18 20 24 30 36
W
BL
Type
Type
2&3
4
5
1&4
1
5 /2
10
1
7 /2
10
8
121/2
101/2
121/2
10
141/2
121/2
141⁄2
12
17
141/2
17
14 16 18
19 21 23
161/2 181/4 201/4
19 21 23
Pipe Size
2, 3, & 5
2 6
3
6 8 10 12 14 16 18 20 24 30 36
11
19 21 23
171⁄2 191⁄2 211/2
/16 C W
Type 3
12
/16 C W
BL
Type 4
12
G BL 12
1
1 W
Type 5
C W
BL
Type 5
12
G BL
12 1
1 W
C W
BL
Notes: • Types 1, 2, and 3 provide for longitudinal movement only. • Types 4 and 5 provide for both longitudinal and transverse movement of piping.
"H" Section Only
Options
(for all types) Fig.439 w/Fig 212 Clamps
PH-3.16
G BL
12 1
/16
G BL
12
BL
Type 4
41/2
12
1
/16
W
13 151⁄2
Type 2
12
Type 3
6
17
C W
W
1
121/2
Type 1
BL
Type 2 1
81⁄2
BOLTED SCHEMATICS
12
W
Hole Spacing C G
BL
Type 1 to 5
10
141/2
WELDED SCHEMATICS Type 1
W
Type 1 to 5
Fig. 439 w/Fig 432 Clamp
G BL
q Fig. 439: Structural "H" Slide Assembly q Fig. 439A: Structural "H"
Pipe Slide Assembly, Complete
Size Range: 6 " through 36" PTFE Pipe Slide Assembly – "H" Type Material: Carbon steel “H” section, PTFE bonded slide plates and carbon steel base. Finish: q Plain, q Painted or q Hot-Dip Galvanized (Welded after Galvanizing and Cold Spray Touched-up) Service: A heavy duty slide support where horizontal movement resulting from expansion and contraction takes place and where a low coefficient of friction is desired. Structural "H" Approvals: Complies with Federal Specification A-A-1192A (Type 35), ANSI/MSS SP-69 and MSS SP-58 (Type 35). Maximum Load: As indicated at 70° F see page 135 for rating factor at higher temperatures. Mounting Plate Maximum Temperature: 750° F Temperature Range at PTFE: -20° F to 400° F Features: • No lubrication required. PTFE Slides • Allows up to 4" of insulation. • Allows up to 10” travel standard. • Weld in place design. Available Options: • Increased travels. PTFE Slide Plate Base • Increased “H” Section heights. • Clamps, Fig. 212 or Fig. 432. • Base plate with mounting holes. The bolt spacing for the bolted base plates is equal to the “W” dimention minus 1 1⁄2" and the “BL” Note: In the PH-92 and PH-92R Catalogs: dimention minus 1 1⁄2" for all pipe sizes and the hole diameter is The Fig. 439 (slide “H” section only) formerly referred to as 9⁄16" for all sizes. Fig. 437. The Fig. 439 (slide base plate) formerly referred to as Ordering: S pecify figure number, type, name, finish and any other Fig. 438 (slide base plate). option desired. The acceptability of galvanized coatings at temperatures Notes: T ypes 1, 2, and 3 provide for longitudinal movement only. Types 4 above 450°F is at the discretion of the end user. and 5 provide for both longitudinal and transverse movement of piping.
FIG. 439: DIMENSIONS (IN) • LOADS (LBS) Pipe Size
FIELD WELD PIPE TO FIG 439
D B
PTFE SLIDE PLATES
6 8 10 12 14 16 18 20 24 30 36
1&4
B
D*
Type
Type
2&5
3
5
51⁄4
55⁄16
51⁄8
53⁄8
57⁄16
51⁄4 61⁄4 67⁄16
51⁄2 65⁄8 613⁄16
59⁄16 611⁄16 63⁄4
Max Load
1&4
2&5
3
73⁄4 83⁄4 95⁄8 103⁄4 107⁄8 121⁄8 125⁄8 133⁄4 155⁄8 195⁄8 23
8 9 97⁄8 11 111⁄8 123⁄8 127⁄8 14 157⁄8 197⁄8 231⁄4
8 9 915⁄16 111⁄16 113⁄16 127⁄16 1215⁄16 141⁄16 1515⁄16 201⁄16 237⁄16
Down
Side Up Type Type 3 2, 3, 5
12,000 3,000
1,200
16,000 4,000
1,600
24,000 6,000
2,400
* With clamps; add material thickness of a Fig. 212 for bolted bases add 5⁄16" to height “H” dimension. ** With the Figure 432 special clamp, add the material thickness of Figure 432.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved q Approved as noted q Not approved
Engineer:
Remarks:
Project: Address:
Submittal Date: Notes 1: Notes 2: PH-1.15
GUIDES & SLIDES
Fig. 439
Structural “H” Slide Assembly, Complete BOLTED: DIMENSIONS (IN)
WELDED: DIMENSIONS (IN) Pipe Size
1
6 8 10 12 14 16 18 20 24 30 36
W
BL
Type
Type
2&3
4
5
1&4
1
5 /2
10
1
7 /2
10
8
121/2
101/2
121/2
10
141/2
121/2
141⁄2
12
17
141/2
17
14 16 18
19 21 23
161/2 181/4 201/4
19 21 23
Pipe Size
2, 3, & 5
2 6
3
6 8 10 12 14 16 18 20 24 30 36
11
19 21 23
171⁄2 191⁄2 211/2
/16 C W
Type 3
12
/16 C W
BL
Type 4
12
G BL 12
1
1 W
Type 5
C W
BL
Type 5
12
G BL
12 1
1 W
C W
BL
Notes: • Types 1, 2, and 3 provide for longitudinal movement only. • Types 4 and 5 provide for both longitudinal and transverse movement of piping.
"H" Section Only
Options
(for all types) Fig.439 w/Fig 212 Clamps
PH-3.16
G BL
12 1
/16
G BL
12
BL
Type 4
41/2
12
1
/16
W
13 151⁄2
Type 2
12
Type 3
6
17
C W
W
1
121/2
Type 1
BL
Type 2 1
81⁄2
BOLTED SCHEMATICS
12
W
Hole Spacing C G
BL
Type 1 to 5
10
141/2
WELDED SCHEMATICS Type 1
W
Type 1 to 5
Fig. 439 w/Fig 432 Clamp
G BL
