Home Care Technical Specification - Moen
Home Care Technical Specification Designer Angled Grab Bar w/ Grip Pad
Dimensions:
Stock Numbers:
LRA8716D1G
LRA8716D1GBN – 16” Designer Angled Grab Bar Brushed Nickel Finish, 1 ¼” Bar, Concealed Screw Mounting
Installation Instructions: 1. 2.
Materials: 1 ¼” Grab Bar rods are formed from (.040) type 304 stainless steel tubing.
Ple ase note that scre ws MUST be mounted into a wood stud for secure installation. Slide the decorative cover away from the hub end to e xpose the SecureMount™ m ounting flange. Do not remove protective plastic from decorative cover until indicated later in these instructions. 3. Locate the studs behind the wall by using a stud sensor or other stud locating m e thod. Studs are usually 16 in. apart; locate the center of each stud. 4. Moving aside the decorative cover as needed, with a pencil, mark th ree of the m ounting locations on e ach of the two grab bar flanges. Two m arks to be made above the grab bar in the area indicated in the illustration below. The third m ark to be m ade below the grab bar in the area indicated in the illustration below. De cide whe ther you would like to position your grab bar horizontally, ve rtically or at an angle, re membering that BOTH ends of the grab bar MUST be positioned ove r a wood stud. 5. Moving the decorative cover as far away from the marked slots as possible, drill a hole into the m arks, through the slots (as shown in illustration). Position the drill at a slight angle in order to get around the grab bar and decorative cover, making sure to drill into the wood stud. If desired, apply silicone caulk to the back of the de corative cover to guard against wate r penetration. 6. To m ount the grab bar, re position one end of the grab bar SecureMount™ m ounting flange over the m arked holes. 7. Thre ad a washer onto each screw. Using the screwdriver, screw the wood scre ws with washe rs into the Se cureMount™ mounting flange at one end of the grab bar. The n screw the wood screws with washers into the mounting flange at the other e nd of the grab bar. 8. Tighten the scre ws until secure. 9. Slide the decorative cover over the Se cure Mount™ m ounting flange, rotating to find the corre ct fit before snapping into place. 10. Slide decorative covers over Se cureMount™ mounting flanges.
Stock Number:_________________________Grab Bars By Creative Specialties 2 5 3 0 0 A L MO E N D R I V E N O R TH O L MS TE D , O H 4 4 0 7 0 C O R P O R A TE H E A D Q U A R TE R S : ( 8 0 0 ) 3 2 1 - 8 8 0 9 F A X: ( 8 0 0 ) 8 4 8 - 6 6 3 6 I N TE R N A TI O N A L : ( 4 4 0 ) 9 6 2 - 2 0 0 0 F A X: ( 4 4 0 ) 9 6 2 - 2 7 2 6 C U S TO ME R S E R V I C E ( U S A ) : 8 0 0 - 8 8 2 - 0 1 1 6 F A X: ( 8 8 8 ) 3 7 9 - 2 7 2 0 W W W . MO E N . C O M
Copyright Creative Specialties International
Literature #BA1670
Dimensions:
Stock Numbers:
LRA8716D1G
LRA8716D1GBN – 16” Designer Angled Grab Bar Brushed Nickel Finish, 1 ¼” Bar, Concealed Screw Mounting
Installation Instructions: 1. 2.
Materials: 1 ¼” Grab Bar rods are formed from (.040) type 304 stainless steel tubing.
Ple ase note that scre ws MUST be mounted into a wood stud for secure installation. Slide the decorative cover away from the hub end to e xpose the SecureMount™ m ounting flange. Do not remove protective plastic from decorative cover until indicated later in these instructions. 3. Locate the studs behind the wall by using a stud sensor or other stud locating m e thod. Studs are usually 16 in. apart; locate the center of each stud. 4. Moving aside the decorative cover as needed, with a pencil, mark th ree of the m ounting locations on e ach of the two grab bar flanges. Two m arks to be made above the grab bar in the area indicated in the illustration below. The third m ark to be m ade below the grab bar in the area indicated in the illustration below. De cide whe ther you would like to position your grab bar horizontally, ve rtically or at an angle, re membering that BOTH ends of the grab bar MUST be positioned ove r a wood stud. 5. Moving the decorative cover as far away from the marked slots as possible, drill a hole into the m arks, through the slots (as shown in illustration). Position the drill at a slight angle in order to get around the grab bar and decorative cover, making sure to drill into the wood stud. If desired, apply silicone caulk to the back of the de corative cover to guard against wate r penetration. 6. To m ount the grab bar, re position one end of the grab bar SecureMount™ m ounting flange over the m arked holes. 7. Thre ad a washer onto each screw. Using the screwdriver, screw the wood scre ws with washe rs into the Se cureMount™ mounting flange at one end of the grab bar. The n screw the wood screws with washers into the mounting flange at the other e nd of the grab bar. 8. Tighten the scre ws until secure. 9. Slide the decorative cover over the Se cure Mount™ m ounting flange, rotating to find the corre ct fit before snapping into place. 10. Slide decorative covers over Se cureMount™ mounting flanges.
Stock Number:_________________________Grab Bars By Creative Specialties 2 5 3 0 0 A L MO E N D R I V E N O R TH O L MS TE D , O H 4 4 0 7 0 C O R P O R A TE H E A D Q U A R TE R S : ( 8 0 0 ) 3 2 1 - 8 8 0 9 F A X: ( 8 0 0 ) 8 4 8 - 6 6 3 6 I N TE R N A TI O N A L : ( 4 4 0 ) 9 6 2 - 2 0 0 0 F A X: ( 4 4 0 ) 9 6 2 - 2 7 2 6 C U S TO ME R S E R V I C E ( U S A ) : 8 0 0 - 8 8 2 - 0 1 1 6 F A X: ( 8 8 8 ) 3 7 9 - 2 7 2 0 W W W . MO E N . C O M
Copyright Creative Specialties International
Literature #BA1670
