HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement Written By: jrw01
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
TOOLS:
PARTS:
Metal Spudger Set (1)
HP LaserJet 1160 or 1320 Duplexer Solenoid (1)
Phillips #0 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 1 — Left Side Cover
Pull on the two tabs on the back of the printer to release the left side cover.
Remove the cover by rotating it towards the front of the printer.
Step 2 — Right Side Cover
With the printer turned so that the right side is facing upwards, use a metal spudger to disengage 3 tabs holding the right side cover in place.
Lift the cover off of the printer.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 3 — Back Cover
Remove 4 screws on the back of the printer.
Remove the back cover.
Step 4 — Top Cover
Remove 2 screws on the back of the printer, one on the left, and one on the front.
The second image shows the formatter removed, but it is not necessary to remove the formatter to replace the top cover.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 5 — Top Cover
Disconnect the control panel cable and remove the top cover.
Step 6 — Fan
Disconnect the fan cable from the main board of the printer.
Remove the retaining clip holding the fan in.
Remove the 2 screws holding the fan in.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 7 — Fan Cable
Remove the fan cable from the cable guide.
Step 8 — Duplexer PCB
Disconnect one cable from the main board of the printer.
Disconnect the duplexer solenoid cable from the duplexer PCB.
Remove one screw on the duplexer PCB and remove the PCB from the printer.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 9 — Duplexer Gears
Remove 3 screws holding the duplexer gears to the printer and remove the gears.
Step 10 — Duplexer Solenoid
Remove one screw to remove the solenoid from the printer.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-24 04:34:00 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement Written By: jrw01
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
TOOLS:
PARTS:
Metal Spudger Set (1)
HP LaserJet 1160 or 1320 Duplexer Solenoid (1)
Phillips #0 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 1 — Left Side Cover
Pull on the two tabs on the back of the printer to release the left side cover.
Remove the cover by rotating it towards the front of the printer.
Step 2 — Right Side Cover
With the printer turned so that the right side is facing upwards, use a metal spudger to disengage 3 tabs holding the right side cover in place.
Lift the cover off of the printer.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 3 — Back Cover
Remove 4 screws on the back of the printer.
Remove the back cover.
Step 4 — Top Cover
Remove 2 screws on the back of the printer, one on the left, and one on the front.
The second image shows the formatter removed, but it is not necessary to remove the formatter to replace the top cover.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 5 — Top Cover
Disconnect the control panel cable and remove the top cover.
Step 6 — Fan
Disconnect the fan cable from the main board of the printer.
Remove the retaining clip holding the fan in.
Remove the 2 screws holding the fan in.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 7 — Fan Cable
Remove the fan cable from the cable guide.
Step 8 — Duplexer PCB
Disconnect one cable from the main board of the printer.
Disconnect the duplexer solenoid cable from the duplexer PCB.
Remove one screw on the duplexer PCB and remove the PCB from the printer.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
Step 9 — Duplexer Gears
Remove 3 screws holding the duplexer gears to the printer and remove the gears.
Step 10 — Duplexer Solenoid
Remove one screw to remove the solenoid from the printer.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-24 04:34:00 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
HP LaserJet 1160 or 1320 Duplexer Solenoid Replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
