Impulse G2 Height Adjustable Assembly
IMPULSE G2/PULSE
PART # 1608990
STATIC BRIDGE & RETURN MODULE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a static bridge or return module with the “FX” no hinged access panel back option to a height adjustable freestanding desk.
2.
Begin by removing the outside access panel on the connecting end of the desk. The access panel can be removed by lifting upwards and then outward as illustrated in the upper most view. Next, remove the two outer most factory installed screws on the connecting panel of the desk, as shown in the view below. The inner most screws will be removed at a later time.
3.
4.
Tools Required: TOOLS REQUIRED:
Drill Drill Dwg:
Locate the loose support panel included with your height adjustable desk. Place it directly against the connecting end of the desk, making TOOLS REQUIRED: sure the bottom edges are flush with each other, and that theINSTRUCTIONS back edge will align with the face of the access panel. Secure the panel in place Outside by fastening the supplied wood screws from the HK-67 kit through the Access clearance holes and into the support panel, as shown below. A pilot hole Access Panel Outside Panel can be drilled prior to fastening the screws. Repeat the process for the remaining inner most screws. The access panel can now be re-installed. Drill Position the bridge/return next to the desk, making sure all are aligned with each other and level. Once the modules are in their correct position, fasten together by using the supplied “L” brackets and wood screws from the HK-10 kit as shown below.
Rev:
1608990
"L" “L”Bracket
Bracket
Desk Connecting Desk Connecting Panel Panel
Support Support Panel
Bridge Bridge Back Back Panel Panel
•
Static
ThisSupport sheet covers the steps to in Panel Panelto a height adjustable f option
Static Bridge & Return Module Installation
• •
• Beginpanel by removing the outside This sheet covers the steps to install a static bridge or return module with the "FX" no hinged access back removed by lifting upwards an option to a height adjustable freestanding desk.
most factory installed screws o
Begin by removing the outside access panel on the connecting end of the desk. The accessscrews panel can willbe be removed at a la removed by lifting upwards and then outward as illustrated in the upper most view. Next, remove the two outer most factory installed screws on the connecting panel of the desk, as shown in the view above. The inner • Locate the most loose support pane screws will be removed at a later time.
IMPULSE G2/PULSE
PART # 1608991
STATIC BRIDGE & RETURN MODULE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a static bridge or return module with the “FZ” hinged access panel back option to a height adjustable freestanding desk.
2.
Begin by locating the loose support panel included with your height adjustable desk. Place it directly against the connecting end of the bridge/return making sure the back and bottom edges are flush with each other as shown in the view below. Secure the panel in place by fastening the supplied wood screws from the HK-48 kit through the mounting holes in the bridge/return and into the support panel.
3.
4.
Tools Required: TOOLS REQUIRED:
Drill Drill
Next, remove the outside access panel on the connecting end of the desk. The access panel can be removed by lifting upwards and then outward as illustrated in the upper most view. Remove the two outer TOOLS REQUIRED: most factory installed screws on the connecting panel of the desk, as INSTRUCTIONS shown in the view below. The inner most screws will be removed at a later time.
Dwg:
Rev:
1608991
Outside Access Position the bridge/return next to the desk, making sure all are aligned Outside Access Panel with each other and level. Once the modules are in their correct position, Panel fasten togetherDrill by screwing the supplied wood screws from the HK-67 kit through the clearance holes and into the support panel. A pilot hole can be drilled prior to fastening the screws. Repeat the process for the inner most screws. The access panel can now be re-installed.
Bridge
Bridge Connecting Connecting Panel Panel
Desk DeskConnecting Connecting Panel
Support Support Panel Panel
Static Support • Support Panel Panel
This sheet covers the steps to in option to a height adjustable f
• Bridge & Return Module Installation
• •
Begin by removing the outside removed by lifting upwards an most factory This sheet covers the steps to install a static bridge or return module with the "FZ" hinged access panel back installed screws o option to a height adjustable freestanding desk. screws will be removed at a la
Begin by locating the loose support panel included with your height adjustable desk. Place it directly against • flush Locate the loose support pane the connecting end of the bridge/return making sure the back and bottom edges are with each other
IMPULSE G2
PART # 1608992
HEIGHT ADJUSTABLE BRIDGE & RETURN MODULE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a height adjustable bridge or return module to a height adjustable freestanding desk.
2.
Begin by removing the outside access panel on the connecting end of the desk. The access panel can be removed by lifting upwards and then outward as illustrated in the upper most view. Next, remove the two outer most factory installed screws on the connecting panel of the desk, as shown in the view above. The inner most screws will be removed at a later time.
3.
Tools Required: TOOLS REQUIRED:
Drill Drill
Position the bridge/return next to the desk, making sure all are aligned with each other and level. Once the modules are in their correct position, fasten together by screwing the supplied wood screws from the HK-67 kit through the clearance holes and into the support panel, as shown REQUIRED: below. ATOOLS pilot hole can be drilled prior to fastening the screws. Repeat INSTRUCTIONS the process for the remaining inner most screws. The access panel can now be re-installed.
Dwg:
Rev:
1608992
Outside Access
Outside Access Panel Panel Drill
Static • Desk Connecting Panel Desk Connecting Panel
•
Bridge & Return Module Installation
•
This sheet covers the steps to in option to a height adjustable f
Bridge Connecting Panel Bridge Connecting Panel
Begin by removing the outside removed by lifting upwards an most factory installed screws o screws will be removed at a la
• Locate the loose support pane This sheet covers the steps to install a height adjustable bridge or return module to a height adjustable
IMPULSE G2
PART # 1608993
HEIGHT ADJUSTABLE BRIDGE & RETURN MODULE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a height adjustable bridge or return module to a static freestanding desk or credenza.
Tools Required: TOOLS REQUIRED:
NOTE: The bridge/return has been designed to allow a 1" clearance between adjacent worksurfaces. Position the bridge/return next to the desk/credenza, making sure the face of the support panel is placed directly against the edge of the end panel. Verify all modules are all aligned, then fasten together using the supplied “L” brackets and wood screws from the HK-10 kit as shown above. Repeat for remaining connecting end, if installing a bridge module. TOOLS REQUIRED:
Dwg:
INSTRUCTIONS
Drill Drill
Rev:
1608993
1" 1" Drill
1" 1"
Credenza/Desk
Credenza/Desk Worksurface Worksurface
Credenza/Desk Credenza/Desk End EndPanel Panel Support
Support Panel Panel
Static
Bridge & Return Module Installation
•
•
This sheet covers the steps to in option to a height adjustable f
•
Begin by removing the outside removed by lifting upwards an most factory installed screws o screws will be removed at a la
Locate the loose support pane This sheet covers the steps to install a height adjustable bridge or return module to a•static freestanding
IMPULSE G2
PART # 1608994
RUNOFF WORKTABLE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a height adjustable runoff worktable to a static credenza.
2.
Begin by positioning the back of the worktable directly up against the user side of the credenza, making sure the end panel on the credenza is flush with the end panel on the panel base. The panel base height will match up to the bottom of the credenza worksurface.
3.
Using the views below as a guide, secure the worktable in place by fastening the supplied “L” brackets from the to the upper part of the panel base, and then to the worksurface and end panel on the credenza. The attaching screws and “L” bracket can be found in the HK-10 and HK-11 kits. NOTE: The view is shown with the worktable connecting to a lateral file credenza with the hinged access panel back option. The hinged access panel is not shown for clarity purposes.
4.
Tools Required: TOOLS REQUIRED:
Drill Drill
The back of the worktable panel base features a removable access panel. The panel is held in place with a “snap-in” connector at each corner. To remove, grab the panel through the grommet TOOLS hole and pull REQUIRED: outwards. INSTRUCTIONS
Dwg:
Rev:
1608994
Drill
DETAIL A DETAIL
Align flush flush with with Align each other each other
Credenza Credenza
DETAIL BB DETAIL "L" Brackets “L”
Removable RemovableAccess AccessPanel Panel WorktablePanel PanelBase Base Worktable
•
Runoff Worktable Installation
Static
•
This sheet covers the steps to in option to a height adjustable f
•
Begin by removing the outside removed by lifting upwards an most factory installed screws o screws will be removed at a la
• Locate the loose support pane This sheet covers the steps to install a height adjustable runoff worktable to a static credenza.
IMPULSE G2/PULSE
INSTRUCTIONS
FREESTANDING TABLE
PART # 1608995
Rev:
Dwg:
Rev:
Dwg:
INSTRUCTIONS
FREESTANDING TABLE INSTALLATION INSTRUCTIONS ASSEMBLY FREESTANDING TABLE • Place work surface bottom side Attach mounting hardware to ASSEMBLY up on a non-marring surface. top 1. of columns. Attach mounting hardware to top of columns. • Attach mounting hardware to (4) M6 x 16MM head cap screws, per Use 2. (4) Use M6 x 16MM flatflathead top of columns. column, to attach mounting cap screws, per column ,to plate to top of column. attach plate to topflat head • mounting Use (4) M6 x 16MM of column. cap screws, per column ,to attach mounting plate to top of column.
•
•
Tools Required: Required Tools:
• Place work surface bottom side Align holes platesurface. up on on mounting a non-marring with pre-drilled holes on bottom side of surface. • work Align holes on mounting plate with pre-drilled holes on bottom Fasten mounting hardware side of work surface.to worksurface using (8) #12 X Cordless 1" Cordless Screwdriver Screwdriver truss head screwsmounting per column. • Fasten hardware to worksurface using (8) #12 X 1" truss head screws per column. 5mm AllenWrench Wrench 5mm Allen
Level Level Dwg:
Rev:
NS
TABLE 3. work Place surface work surface bottom side Place bottom sideup on a nonsurface. surface. up on a marring non-marring
6.
Align bolt holes in feet with threaded holes in the bottom of columns.
4. Align holes on mounting plate with preAlign holes on mounting plate drilled holes on bottom side of worksurface. with pre-drilled holes on bottom side 5. of work surface. Fasten mounting hardware to worksurface
7.
Attach feet to columns using (4) M6 x 20MM socket head cap screws per column.
using (8) #12 X 1" truss head screws per
Fasten mounting hardware to • Align bolt holes in feet with column. Required Tools: worksurface using (8) #12 X 1"threaded holes in the truss head screws per column.bottom of columns. • Align bolt holes in feet with Required Tools: threaded holes in the • Attach feet to columns using bottom of columns. (4) M6 x 20MM socket head cap•screws per column. Attach feet to columns using (4) M6 x 20MM socket head ordless Screwdriver cap screws per column. Cordless Screwdriver
5mm Allen Wrench 5mm Allen Wrench Level
with
Level
PAGE 1 OF 3
•
Al th bo
•
At (4 ca
IMPULSE G2/PULSE
Rev:
Dwg:
INSTRUCTIONS FREESTANDING TABLE
FREESTANDING TABLE ASSEMBLY
INSTALLATION INSTRUCTIONS
8.
9.
Align• two thru holestwo in control with in control Align thru box holes pre-drilled holes on bottom side of work box with pre-drilledholes on surface.
Dwg:
Rev:
INSTRUCTIONS
Control Panel CONTROL PANEL bottom side of work surface. FREESTANDING TABLE
Use (2) #8 x 2" pan head screws to secure to • Use (2) #8 x 2" pan head worksurface.
screws to secure to work surface.
ASSEMBLY
10. To attach control panel, determine if control •is to be Toonattach panel, • panel Align two thru inside control the leftholes orcontrol right of the determine if control panel is to be on the box with pre-drilledholes on worksurface.
left or right sidesurface. of the work surface. bottom side of work
11. Align control panel mount plate with • (2)holes. Align panelscrews mount • pre-drilled Use #8 x control 2" pan head
withto pre-drilled holes. to secure work surface.
Control Box CONTROL BOX
CONTROL PANEL
plate
CONTROL 12. Use (2) X8 x 5/8" pan head screws to secure • attach Use (2) X8 x panel, 5/8" pan head screws • to worksurface. To control determine
BOX
to secure surface. if control panel istotowork be on the left or right side of the work surface.
•
Align control panel mount plate with pre-drilled holes.
•
Use (2) X8 x 5/8" pan head screws to secure to work surface.
NOTE: When attaching control box, use the grooves on the upper face to help manage motor cables.
NOTE: When attaching control box, useon NOTE: When attaching control box, use the grooves the grooves upper face to help the upper face to on helpthe manage motor cables. manage motor cables.
Use "hook" for mains cable (power cord) relief.
Use forfor mains cablecable Use“hook” "hook" mains (power cord) relief.relief. (power cord)
PAGE 2 OF 3
IMPULSE G2/PULSE
Dwg:
INSTRUCTIONS
FREESTANDING TABLE INSTALLATION INSTRUCTIONS
FREESTANDING TABLE ASSEMBLY
13. Snap together motor cable ends and leg cables. (Figure A)
•
Snap together motor cable ends and leg cables. (Figure A)
14. Plug the other end of the motor cable to the control box.
•
Plug the other end of the motor cable to the control box.
•
Plug control panel cord into control box.
•
Last, plug in mains cable to control box.
•
Secure cables using provided cord clips and velcro strips.
15. Plug control panel cord into control box. 16. Last, plug in mains cable to control box.
17. Secure cables using provided cord clips and velcro strips.
Mains Mains Cable Cable
Cable LegLegCable
Figure Figure AA
Motor MotorCable Cable
18. Table must be completely leveled before use.
Table mustthem be in completely 19. Adjust•levelers by turning or out.
leveled before use.
Adjust levelers 20. Table• must be level from side to by sideturning and front them to back.in •
PAGE 3 OF 3
or out.
Table must be level from side to side and front to back.
Control Control Panel Panel Cord Cord
Rev:
IMPULSE G2
PART # 1609010
HEIGHT ADJUSTABLE BRIDGE & RETURN SET UP GUIDE
1.
This sheet covers the details to correctly set up your height adjustable unit.
2.
The control switch has been temporarily mounted in a protected area underneath the worksurface to prevent any damage during shipping. Remove the mounting screw(s) and place the switch in a visible and obstruction free postion. Fasten the switch to the worksurface utilizing the two mounting holes on the bracket.
3.
The power cord has been routed through the wire manager and into the chassis during shipping. Pull on the ribbon tape located at the bottom of the unit to bring the power cord out. NOTE: It is recommended to use a power supply (PS-77) to power the height adjustable unit if any electrical accessories are installed onto it. This will aid in the process of properly managing power cords underneath the worksurface.
4.
To route cables through the wire management column, rotate the retainer bracket and place the cable into the pocket in the worksurface. Rotate the bracket back into place so that the cable is secured into the pocket, as shown in the view below. The cables can then pass through the column as shown the Dwg: upper left view. To gain access and further manage cables inside the chassis, lift upward and then TOOLS REQUIRED: outward on the front removable panel and set aside.
Tools Required: TOOLS REQUIRED:
Drill Drill
INSTRUCTIONS
Drill
Rev:
1609010
Ribbon Ribbon Tape Tape
PS-77 PS-77
Desired Desired Location Location Wire Wire Management Management Column Column Wire Wire Pass Pass Thru Thru
Factory Factory Installed Installed Location Location
Static
Retainer Bracket • Bracket This sheet covers the steps to in Retainer
option to a height adjustable f
Removable Removable Panel Panel
•
HA Bridge & Return Set Up Guide
This sheet covers the details to correctly set up your height adjustable unit.
•
Begin by removing the outside
•
Locate the loose support pane
removed by lifting upwards an Wire Wire Management Column most factory installed screws o Management screws will be removed at a la Column
IMPULSE G2/PULSE
PART # 1609011
HEIGHT ADJUSTABLE DESK SET UP GUIDE
1.
This sheet covers the details to correctly set up your height adjustable unit.
2.
The control switch has been temporarily mounted in a protected area underneath the worksurface to prevent any damage during shipping. Remove the mounting screw(s) and place the switch in a visible and obstruction free postion. Fasten the switch to the worksurface utilizing the two mounting holes on the bracket. NOTE: It is recommended to use a power supply (PS-77) to power the height adjustable unit if any electrical accessories are installed onto it. This will aid in the process of properly managing power cords underneath the worksurface.
3.
A wire manager is included to use with your desk and is intended to be installed in between the worksurface and fixed shelf. To assemble the wire manager, slide the mounting clip onto the manager as shown in the views below. The slot on the clip aligns with the flat narrow sections of the manager.
4.
The wire manager can be installed on either the left or right side of the fixed shelf, near the corner notches. Raise the worksurface to the upper most height, then locate an area above and below that will allow for a clear mounting position. Approximate locations are shown in the views below. Fasten the mounting clips, making sure the mounting clips are relatively straight and parallel with each other. This will ensure that the wire manager will not bind or stress when the worksurface is lowered.
5.
1609011
Wires and cables can then be passed through the wire manager, the notch TOOLS of the shelf, andREQUIRED: finally routed through the pedestal and/or base as illustrated in the views below. To gain access inside the panel base, lift upward and then outward on the outside end panel and set aside. Drill
Tools Required: TOOLS REQUIRED:
Drill Drill
Dwg:
Rev:
INSTRUCTIONS
Factory Installed Factory Installed Location Location
Desired Desired Location Location
PS-77 PS-77
Worksurface Location Worksurface Location
Upper UpperPosition Position Wire Wire Manager Manager shown shown installed on the the right rightside side installed on LowerPosition Position Lower Mount Mount Clip Clip
Static • Wire Manager Manager Wire
• •
Begin by removing the outside removed by lifting upwards an This sheet covers the details to correctly set up your height adjustable unit. most factory installed screws o screws will be removed at a la The control switch has been temporarily mounted in a protected area underneath the worksurface to prevent any damage
HA Desk Set Up Guide
•
This sheet covers the steps to in a height adjustable f
Power Cord Power Cord option to Shelf Location Shelf Location
during shipping. Remove the mounting screw(s) and place the switch in a visible and obstruction free postion. Fasten the • Locate the loose switch to the worksurface utilizing the two mounting holes on the bracket.
support pane
PART # 1608990
STATIC BRIDGE & RETURN MODULE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a static bridge or return module with the “FX” no hinged access panel back option to a height adjustable freestanding desk.
2.
Begin by removing the outside access panel on the connecting end of the desk. The access panel can be removed by lifting upwards and then outward as illustrated in the upper most view. Next, remove the two outer most factory installed screws on the connecting panel of the desk, as shown in the view below. The inner most screws will be removed at a later time.
3.
4.
Tools Required: TOOLS REQUIRED:
Drill Drill Dwg:
Locate the loose support panel included with your height adjustable desk. Place it directly against the connecting end of the desk, making TOOLS REQUIRED: sure the bottom edges are flush with each other, and that theINSTRUCTIONS back edge will align with the face of the access panel. Secure the panel in place Outside by fastening the supplied wood screws from the HK-67 kit through the Access clearance holes and into the support panel, as shown below. A pilot hole Access Panel Outside Panel can be drilled prior to fastening the screws. Repeat the process for the remaining inner most screws. The access panel can now be re-installed. Drill Position the bridge/return next to the desk, making sure all are aligned with each other and level. Once the modules are in their correct position, fasten together by using the supplied “L” brackets and wood screws from the HK-10 kit as shown below.
Rev:
1608990
"L" “L”Bracket
Bracket
Desk Connecting Desk Connecting Panel Panel
Support Support Panel
Bridge Bridge Back Back Panel Panel
•
Static
ThisSupport sheet covers the steps to in Panel Panelto a height adjustable f option
Static Bridge & Return Module Installation
• •
• Beginpanel by removing the outside This sheet covers the steps to install a static bridge or return module with the "FX" no hinged access back removed by lifting upwards an option to a height adjustable freestanding desk.
most factory installed screws o
Begin by removing the outside access panel on the connecting end of the desk. The accessscrews panel can willbe be removed at a la removed by lifting upwards and then outward as illustrated in the upper most view. Next, remove the two outer most factory installed screws on the connecting panel of the desk, as shown in the view above. The inner • Locate the most loose support pane screws will be removed at a later time.
IMPULSE G2/PULSE
PART # 1608991
STATIC BRIDGE & RETURN MODULE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a static bridge or return module with the “FZ” hinged access panel back option to a height adjustable freestanding desk.
2.
Begin by locating the loose support panel included with your height adjustable desk. Place it directly against the connecting end of the bridge/return making sure the back and bottom edges are flush with each other as shown in the view below. Secure the panel in place by fastening the supplied wood screws from the HK-48 kit through the mounting holes in the bridge/return and into the support panel.
3.
4.
Tools Required: TOOLS REQUIRED:
Drill Drill
Next, remove the outside access panel on the connecting end of the desk. The access panel can be removed by lifting upwards and then outward as illustrated in the upper most view. Remove the two outer TOOLS REQUIRED: most factory installed screws on the connecting panel of the desk, as INSTRUCTIONS shown in the view below. The inner most screws will be removed at a later time.
Dwg:
Rev:
1608991
Outside Access Position the bridge/return next to the desk, making sure all are aligned Outside Access Panel with each other and level. Once the modules are in their correct position, Panel fasten togetherDrill by screwing the supplied wood screws from the HK-67 kit through the clearance holes and into the support panel. A pilot hole can be drilled prior to fastening the screws. Repeat the process for the inner most screws. The access panel can now be re-installed.
Bridge
Bridge Connecting Connecting Panel Panel
Desk DeskConnecting Connecting Panel
Support Support Panel Panel
Static Support • Support Panel Panel
This sheet covers the steps to in option to a height adjustable f
• Bridge & Return Module Installation
• •
Begin by removing the outside removed by lifting upwards an most factory This sheet covers the steps to install a static bridge or return module with the "FZ" hinged access panel back installed screws o option to a height adjustable freestanding desk. screws will be removed at a la
Begin by locating the loose support panel included with your height adjustable desk. Place it directly against • flush Locate the loose support pane the connecting end of the bridge/return making sure the back and bottom edges are with each other
IMPULSE G2
PART # 1608992
HEIGHT ADJUSTABLE BRIDGE & RETURN MODULE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a height adjustable bridge or return module to a height adjustable freestanding desk.
2.
Begin by removing the outside access panel on the connecting end of the desk. The access panel can be removed by lifting upwards and then outward as illustrated in the upper most view. Next, remove the two outer most factory installed screws on the connecting panel of the desk, as shown in the view above. The inner most screws will be removed at a later time.
3.
Tools Required: TOOLS REQUIRED:
Drill Drill
Position the bridge/return next to the desk, making sure all are aligned with each other and level. Once the modules are in their correct position, fasten together by screwing the supplied wood screws from the HK-67 kit through the clearance holes and into the support panel, as shown REQUIRED: below. ATOOLS pilot hole can be drilled prior to fastening the screws. Repeat INSTRUCTIONS the process for the remaining inner most screws. The access panel can now be re-installed.
Dwg:
Rev:
1608992
Outside Access
Outside Access Panel Panel Drill
Static • Desk Connecting Panel Desk Connecting Panel
•
Bridge & Return Module Installation
•
This sheet covers the steps to in option to a height adjustable f
Bridge Connecting Panel Bridge Connecting Panel
Begin by removing the outside removed by lifting upwards an most factory installed screws o screws will be removed at a la
• Locate the loose support pane This sheet covers the steps to install a height adjustable bridge or return module to a height adjustable
IMPULSE G2
PART # 1608993
HEIGHT ADJUSTABLE BRIDGE & RETURN MODULE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a height adjustable bridge or return module to a static freestanding desk or credenza.
Tools Required: TOOLS REQUIRED:
NOTE: The bridge/return has been designed to allow a 1" clearance between adjacent worksurfaces. Position the bridge/return next to the desk/credenza, making sure the face of the support panel is placed directly against the edge of the end panel. Verify all modules are all aligned, then fasten together using the supplied “L” brackets and wood screws from the HK-10 kit as shown above. Repeat for remaining connecting end, if installing a bridge module. TOOLS REQUIRED:
Dwg:
INSTRUCTIONS
Drill Drill
Rev:
1608993
1" 1" Drill
1" 1"
Credenza/Desk
Credenza/Desk Worksurface Worksurface
Credenza/Desk Credenza/Desk End EndPanel Panel Support
Support Panel Panel
Static
Bridge & Return Module Installation
•
•
This sheet covers the steps to in option to a height adjustable f
•
Begin by removing the outside removed by lifting upwards an most factory installed screws o screws will be removed at a la
Locate the loose support pane This sheet covers the steps to install a height adjustable bridge or return module to a•static freestanding
IMPULSE G2
PART # 1608994
RUNOFF WORKTABLE INSTALLATION INSTRUCTIONS
1.
This sheet covers the steps to install a height adjustable runoff worktable to a static credenza.
2.
Begin by positioning the back of the worktable directly up against the user side of the credenza, making sure the end panel on the credenza is flush with the end panel on the panel base. The panel base height will match up to the bottom of the credenza worksurface.
3.
Using the views below as a guide, secure the worktable in place by fastening the supplied “L” brackets from the to the upper part of the panel base, and then to the worksurface and end panel on the credenza. The attaching screws and “L” bracket can be found in the HK-10 and HK-11 kits. NOTE: The view is shown with the worktable connecting to a lateral file credenza with the hinged access panel back option. The hinged access panel is not shown for clarity purposes.
4.
Tools Required: TOOLS REQUIRED:
Drill Drill
The back of the worktable panel base features a removable access panel. The panel is held in place with a “snap-in” connector at each corner. To remove, grab the panel through the grommet TOOLS hole and pull REQUIRED: outwards. INSTRUCTIONS
Dwg:
Rev:
1608994
Drill
DETAIL A DETAIL
Align flush flush with with Align each other each other
Credenza Credenza
DETAIL BB DETAIL "L" Brackets “L”
Removable RemovableAccess AccessPanel Panel WorktablePanel PanelBase Base Worktable
•
Runoff Worktable Installation
Static
•
This sheet covers the steps to in option to a height adjustable f
•
Begin by removing the outside removed by lifting upwards an most factory installed screws o screws will be removed at a la
• Locate the loose support pane This sheet covers the steps to install a height adjustable runoff worktable to a static credenza.
IMPULSE G2/PULSE
INSTRUCTIONS
FREESTANDING TABLE
PART # 1608995
Rev:
Dwg:
Rev:
Dwg:
INSTRUCTIONS
FREESTANDING TABLE INSTALLATION INSTRUCTIONS ASSEMBLY FREESTANDING TABLE • Place work surface bottom side Attach mounting hardware to ASSEMBLY up on a non-marring surface. top 1. of columns. Attach mounting hardware to top of columns. • Attach mounting hardware to (4) M6 x 16MM head cap screws, per Use 2. (4) Use M6 x 16MM flatflathead top of columns. column, to attach mounting cap screws, per column ,to plate to top of column. attach plate to topflat head • mounting Use (4) M6 x 16MM of column. cap screws, per column ,to attach mounting plate to top of column.
•
•
Tools Required: Required Tools:
• Place work surface bottom side Align holes platesurface. up on on mounting a non-marring with pre-drilled holes on bottom side of surface. • work Align holes on mounting plate with pre-drilled holes on bottom Fasten mounting hardware side of work surface.to worksurface using (8) #12 X Cordless 1" Cordless Screwdriver Screwdriver truss head screwsmounting per column. • Fasten hardware to worksurface using (8) #12 X 1" truss head screws per column. 5mm AllenWrench Wrench 5mm Allen
Level Level Dwg:
Rev:
NS
TABLE 3. work Place surface work surface bottom side Place bottom sideup on a nonsurface. surface. up on a marring non-marring
6.
Align bolt holes in feet with threaded holes in the bottom of columns.
4. Align holes on mounting plate with preAlign holes on mounting plate drilled holes on bottom side of worksurface. with pre-drilled holes on bottom side 5. of work surface. Fasten mounting hardware to worksurface
7.
Attach feet to columns using (4) M6 x 20MM socket head cap screws per column.
using (8) #12 X 1" truss head screws per
Fasten mounting hardware to • Align bolt holes in feet with column. Required Tools: worksurface using (8) #12 X 1"threaded holes in the truss head screws per column.bottom of columns. • Align bolt holes in feet with Required Tools: threaded holes in the • Attach feet to columns using bottom of columns. (4) M6 x 20MM socket head cap•screws per column. Attach feet to columns using (4) M6 x 20MM socket head ordless Screwdriver cap screws per column. Cordless Screwdriver
5mm Allen Wrench 5mm Allen Wrench Level
with
Level
PAGE 1 OF 3
•
Al th bo
•
At (4 ca
IMPULSE G2/PULSE
Rev:
Dwg:
INSTRUCTIONS FREESTANDING TABLE
FREESTANDING TABLE ASSEMBLY
INSTALLATION INSTRUCTIONS
8.
9.
Align• two thru holestwo in control with in control Align thru box holes pre-drilled holes on bottom side of work box with pre-drilledholes on surface.
Dwg:
Rev:
INSTRUCTIONS
Control Panel CONTROL PANEL bottom side of work surface. FREESTANDING TABLE
Use (2) #8 x 2" pan head screws to secure to • Use (2) #8 x 2" pan head worksurface.
screws to secure to work surface.
ASSEMBLY
10. To attach control panel, determine if control •is to be Toonattach panel, • panel Align two thru inside control the leftholes orcontrol right of the determine if control panel is to be on the box with pre-drilledholes on worksurface.
left or right sidesurface. of the work surface. bottom side of work
11. Align control panel mount plate with • (2)holes. Align panelscrews mount • pre-drilled Use #8 x control 2" pan head
withto pre-drilled holes. to secure work surface.
Control Box CONTROL BOX
CONTROL PANEL
plate
CONTROL 12. Use (2) X8 x 5/8" pan head screws to secure • attach Use (2) X8 x panel, 5/8" pan head screws • to worksurface. To control determine
BOX
to secure surface. if control panel istotowork be on the left or right side of the work surface.
•
Align control panel mount plate with pre-drilled holes.
•
Use (2) X8 x 5/8" pan head screws to secure to work surface.
NOTE: When attaching control box, use the grooves on the upper face to help manage motor cables.
NOTE: When attaching control box, useon NOTE: When attaching control box, use the grooves the grooves upper face to help the upper face to on helpthe manage motor cables. manage motor cables.
Use "hook" for mains cable (power cord) relief.
Use forfor mains cablecable Use“hook” "hook" mains (power cord) relief.relief. (power cord)
PAGE 2 OF 3
IMPULSE G2/PULSE
Dwg:
INSTRUCTIONS
FREESTANDING TABLE INSTALLATION INSTRUCTIONS
FREESTANDING TABLE ASSEMBLY
13. Snap together motor cable ends and leg cables. (Figure A)
•
Snap together motor cable ends and leg cables. (Figure A)
14. Plug the other end of the motor cable to the control box.
•
Plug the other end of the motor cable to the control box.
•
Plug control panel cord into control box.
•
Last, plug in mains cable to control box.
•
Secure cables using provided cord clips and velcro strips.
15. Plug control panel cord into control box. 16. Last, plug in mains cable to control box.
17. Secure cables using provided cord clips and velcro strips.
Mains Mains Cable Cable
Cable LegLegCable
Figure Figure AA
Motor MotorCable Cable
18. Table must be completely leveled before use.
Table mustthem be in completely 19. Adjust•levelers by turning or out.
leveled before use.
Adjust levelers 20. Table• must be level from side to by sideturning and front them to back.in •
PAGE 3 OF 3
or out.
Table must be level from side to side and front to back.
Control Control Panel Panel Cord Cord
Rev:
IMPULSE G2
PART # 1609010
HEIGHT ADJUSTABLE BRIDGE & RETURN SET UP GUIDE
1.
This sheet covers the details to correctly set up your height adjustable unit.
2.
The control switch has been temporarily mounted in a protected area underneath the worksurface to prevent any damage during shipping. Remove the mounting screw(s) and place the switch in a visible and obstruction free postion. Fasten the switch to the worksurface utilizing the two mounting holes on the bracket.
3.
The power cord has been routed through the wire manager and into the chassis during shipping. Pull on the ribbon tape located at the bottom of the unit to bring the power cord out. NOTE: It is recommended to use a power supply (PS-77) to power the height adjustable unit if any electrical accessories are installed onto it. This will aid in the process of properly managing power cords underneath the worksurface.
4.
To route cables through the wire management column, rotate the retainer bracket and place the cable into the pocket in the worksurface. Rotate the bracket back into place so that the cable is secured into the pocket, as shown in the view below. The cables can then pass through the column as shown the Dwg: upper left view. To gain access and further manage cables inside the chassis, lift upward and then TOOLS REQUIRED: outward on the front removable panel and set aside.
Tools Required: TOOLS REQUIRED:
Drill Drill
INSTRUCTIONS
Drill
Rev:
1609010
Ribbon Ribbon Tape Tape
PS-77 PS-77
Desired Desired Location Location Wire Wire Management Management Column Column Wire Wire Pass Pass Thru Thru
Factory Factory Installed Installed Location Location
Static
Retainer Bracket • Bracket This sheet covers the steps to in Retainer
option to a height adjustable f
Removable Removable Panel Panel
•
HA Bridge & Return Set Up Guide
This sheet covers the details to correctly set up your height adjustable unit.
•
Begin by removing the outside
•
Locate the loose support pane
removed by lifting upwards an Wire Wire Management Column most factory installed screws o Management screws will be removed at a la Column
IMPULSE G2/PULSE
PART # 1609011
HEIGHT ADJUSTABLE DESK SET UP GUIDE
1.
This sheet covers the details to correctly set up your height adjustable unit.
2.
The control switch has been temporarily mounted in a protected area underneath the worksurface to prevent any damage during shipping. Remove the mounting screw(s) and place the switch in a visible and obstruction free postion. Fasten the switch to the worksurface utilizing the two mounting holes on the bracket. NOTE: It is recommended to use a power supply (PS-77) to power the height adjustable unit if any electrical accessories are installed onto it. This will aid in the process of properly managing power cords underneath the worksurface.
3.
A wire manager is included to use with your desk and is intended to be installed in between the worksurface and fixed shelf. To assemble the wire manager, slide the mounting clip onto the manager as shown in the views below. The slot on the clip aligns with the flat narrow sections of the manager.
4.
The wire manager can be installed on either the left or right side of the fixed shelf, near the corner notches. Raise the worksurface to the upper most height, then locate an area above and below that will allow for a clear mounting position. Approximate locations are shown in the views below. Fasten the mounting clips, making sure the mounting clips are relatively straight and parallel with each other. This will ensure that the wire manager will not bind or stress when the worksurface is lowered.
5.
1609011
Wires and cables can then be passed through the wire manager, the notch TOOLS of the shelf, andREQUIRED: finally routed through the pedestal and/or base as illustrated in the views below. To gain access inside the panel base, lift upward and then outward on the outside end panel and set aside. Drill
Tools Required: TOOLS REQUIRED:
Drill Drill
Dwg:
Rev:
INSTRUCTIONS
Factory Installed Factory Installed Location Location
Desired Desired Location Location
PS-77 PS-77
Worksurface Location Worksurface Location
Upper UpperPosition Position Wire Wire Manager Manager shown shown installed on the the right rightside side installed on LowerPosition Position Lower Mount Mount Clip Clip
Static • Wire Manager Manager Wire
• •
Begin by removing the outside removed by lifting upwards an This sheet covers the details to correctly set up your height adjustable unit. most factory installed screws o screws will be removed at a la The control switch has been temporarily mounted in a protected area underneath the worksurface to prevent any damage
HA Desk Set Up Guide
•
This sheet covers the steps to in a height adjustable f
Power Cord Power Cord option to Shelf Location Shelf Location
during shipping. Remove the mounting screw(s) and place the switch in a visible and obstruction free postion. Fasten the • Locate the loose switch to the worksurface utilizing the two mounting holes on the bracket.
support pane
