InFocus LP540 Projector Lamp Replacement
InFocus LP540 Projector Lamp Replacement
InFocus LP540 Projector Lamp Replacement This guide will assist with replacing a non-functioning projector lamp, which is responsible for providing the light necessary for projection.
Written By: Jorge L Navarro
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
InFocus LP540 Projector Lamp Replacement
INTRODUCTION This guide will assist with replacing a non-functioning projector lamp, which is responsible for providing the light necessary for projection.
TOOLS: Phillips #2 Screwdriver (1) Flathead Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
InFocus LP540 Projector Lamp Replacement
Step 1 — Lamp
Place the projector on its back with the control buttons facing down.
Remove the black 7mm screw on the external case with a Phillips 2 screwdriver.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Use the plastic flat-head to remove the lamp lid.
Page 3 of 5
InFocus LP540 Projector Lamp Replacement
Step 3
Remove the 7mm screw near the bottom center with a Philips 2 screwdriver head.
Loosen but do not remove the 7mm screw near the upper right corner with the Phillips 2 screwdriver head.
Step 4
Grab the silver handle.
Unhook the handle so it can move freely.
Pull the handle straight up until the lamp is completely removed from projector.
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
InFocus LP540 Projector Lamp Replacement This document was last generated on 2017-07-03 12:51:29 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
InFocus LP540 Projector Lamp Replacement This guide will assist with replacing a non-functioning projector lamp, which is responsible for providing the light necessary for projection.
Written By: Jorge L Navarro
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
InFocus LP540 Projector Lamp Replacement
INTRODUCTION This guide will assist with replacing a non-functioning projector lamp, which is responsible for providing the light necessary for projection.
TOOLS: Phillips #2 Screwdriver (1) Flathead Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
InFocus LP540 Projector Lamp Replacement
Step 1 — Lamp
Place the projector on its back with the control buttons facing down.
Remove the black 7mm screw on the external case with a Phillips 2 screwdriver.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Use the plastic flat-head to remove the lamp lid.
Page 3 of 5
InFocus LP540 Projector Lamp Replacement
Step 3
Remove the 7mm screw near the bottom center with a Philips 2 screwdriver head.
Loosen but do not remove the 7mm screw near the upper right corner with the Phillips 2 screwdriver head.
Step 4
Grab the silver handle.
Unhook the handle so it can move freely.
Pull the handle straight up until the lamp is completely removed from projector.
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
InFocus LP540 Projector Lamp Replacement This document was last generated on 2017-07-03 12:51:29 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
