Installation Instructions - Blinds
Hardware Standard Quantity
N300475-A 65101-11727-C
Step 2: Shade Installation z
Installation Instructions
Order Width (X)
Honeycomb Shades Continuous Cordloop
Installation Bracket Hold Down Bracket (Optional) Spacer Block(Optional) 2" Screw for Installation Bracket with spacer block M3.8x51mm screw for Tensioner 1 1/4" Screw for Installation Bracket 3/4" Screw for Hold Down Bracket
93"＜ X 39"＜X 66"＜X ≦ X≦ ≦66" ≦93" 39" 120" 2 3 4 5 2
2
2
4
6
8
2
Remove the Shade
1
d
2
2
2
2
4
6
8
10
4
4
4
4
Step 1: Bracket Installation Measure 3” from both ends of the head rail. Mark bracket location on the mounting surface. Space Evenly
3”
x Make sure the cord is tightened / taut without stretching, twisting or crossing, and the tensioner and control cord does not interfere with raising or lowering the shade before cord tensioner is mounted. x Use 2pcs M3.8x51mm screws to mount the cord x tensioner to the wall or window frame firmly for both inside & outside mount. Please refer to the following steps: Step 2 Step 1
Inside Mount
z
Surface
Wood
Fastener
Allocate a min. distance of 1/16’’ from wall to the front of brackets as below drawing. Use two #8 1 1/4 ” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.
Step 3
#8 1 1/4” Screws (Provided) M3.8x51mm screws #6 3/4” screws
Drywall/Plaster Metal
Wall Anchors, Expansion Bolts (Not Provide) Sheet Metal Screws (Not Provide)
Outside Mount z
z
Check Component/Hardware:
Installation Bracket
Hold Down Bracket (Optional)
Allocate a min. distance of 5/8’’ from wall to the bottom of brackets as below drawing. Use two #8 1 1/4 ”mounting screws to attach each bracket. Use wall anchors for drywall or plaster wall.
Fully raise the shade. Gently pry the bracket off the head rail with a flat screwdriver. Remove the shade.
c
Step 3: Cord Tensioner Installation
Tools:
Installation Screws
z
z
Remove shade from package. Save packaging until shade is installed and working to your satisfaction.
z
z
10
Getting Started
x Power drill x Tape measure x Screwdriver x Level x Pencil
x Pull cord to operate shade. Cord Tensioner must be fully tightened prior to operating the shade.
For proper installation, start with attaching the front rail to the bracket.
1pc for extend distance 10mm 2pcs for extend distance 18mm
Note: Optional flat head screw included. Use as needed.
3”
Position head rail at an angle so that it is hooked to the front of the bracket. Then push it upward to snap into the bracket.
Step 4: How to Install Hold Down Brackets (optional) z
Use #6 3/4” screw to secure each bracket.
Step 5: Shade Operation
d
Note x Keep away from heat, sparks and open flame. x Larger windows may require two people to install. x Proper In the process of installation, must support the shade firmly to avoid it fall down too quick to damage the people or itself. x Operate shade only by pulling the cord. x To ensure child safety, install cord cleat and tighten up any loose cords after the shade is installed
Cleaning Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).
N300476 65101-11728
52”<X72”, 4 M3.5×25mm Screw (for Base, M3.5×25mm Screw (for Base, 3/4”S & 3/8”D, Inside Mount)
M3.8x38mm screw (for Wall Mount)
L bracket qty*2 2
base on L bracket, Wall Mount)
Mount)
3/8” Single
3/8”Double & 3/4”Single with Rail Cover
Getting Started Remove the shade from the package. Save the packaging until the shade is installed and working to your satisfaction.
Wood
Bracket Installation
Handle Installation
Inside Mount – for 3/8”Single Cell For flush mount, the minimum distance from the top/bottom wall to the base side is 1/4” and 1/8” from the side wall to the edge of Base. Use M3.5×25mm Screw to secure the base. Align the cover with the notch of the base and push the cover in toward the wall.
Slide the handle onto the plastic piece pre-attached to the rails.
notch 1/4” Base 1/8” step1
step 2 (Top)
You will need to use the following fasteners for your particular mounting surface. Surface
1pc to extend distance 10mm 2pcs to extend distance 18mm
Cover
Tools Needed： x Power drill and drill bit x Measuring tape x Screwdriver x Level x Pencil
Fastener M3.5×25mm Screws (Provided)
M3.8×38mm Wall Anchors, Expansion Bolts Drywall/Plaster (Not Provided) Sheet Metal Screws Metal (Not Provided)
(for 3/8” Single)
L Bracket for windows with marble sill (Optional) (for 3/8”S) L bracket (for 3/4”Single & 3/8”Doubld, Wall Mount)
Step 2
Step1
Notes For child safety, please check and ensure that there are no loose cords after the shade is completely installed. Please also make sure that cords are nice and tight and not tangled.
9
step3
2
Cleaning
Inside Mount – for 3/8” Double Cell & 3/4”Single Cell For flush mount TOP, the minimum distance from the left/right side wall to the end of rail cover is 1/8” and the distance from the center of screw hole to edge of wall is A (A=1 1/16” for 3/8”D & A=1 1/4” for 3/4”S). Use M3.5×25mm Screw to secure the rail cover. Align the cover with the notch of the base and push the cover in toward the wall.
Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!). Cord Equalizer Housing Base
X≦50" 2
X>50" 4
4
7
Cord Equalizer Housing Base (for 3/4”Single & 3/8”Double) L Bracket (for 3/8”S, Wall Mount)
(Top View) Outside Mount – for 3/8”Single Cell Allocate a minimum distance of 3/8” from top window opening to the L bracket and align L bracket 1/16” away from shade end. Use two M3.8x38mm screws to fasten the L bracket. Once the L bracket is installed, use one M3 x 3.6mm bolt to attach base. Finally, align the cover with the notch of the base and push the cover in, as shown in “Inside Mount” illustration. (Top)
5/16''
Hardware Order Width (X) Handle Cord Equalizer Housing Base
(Bottom) Install the bracket similar to previous step but in reverse. Use one M3 x 3.6mm bolt to attach base.
8.5”<X≦40”, 4 40”<X≦52”, 5 52”<X72”, 6
M3 x 3.6mm Bolt (for locking Spacer Block (Optional, Wall
Side mount L bracket for windows with marble sill (optional for 3/8”Single) Allocate a distance of 1/4” from bottom corner window frame and use two M3.8×38mm screws to secure the L bracket. Use one M3 x 3.6mm bolt to attach base to the L bracket (through inner screw hole)
4
3/8” S, Inside Mount)
Honeycomb Shades SmartFitTM
push the cover in, as shown in “Inside Mount” illustration.
5/8''
Installation Instructions
Align the cover with the notch of the base and push the cover in toward the wall.
(Bottom View)
2 4
7
2
2
8.5”<X≦ 40”, 2 40”<X≦ 52”, 3
For flush mount BOTTOM, the minimum distance from the bottom wall to the base side is 1/8” and the distance from the edge of wall to the center of the screw hole is A (A=11/16” for 3/8”D & A=7/8” for 3/4”S). Use M3.5×25mm Screw to secure the base.
(Bottom) Install the bracket similar to top steps but in reverse way. Outside Mount – for 3/8”Double Cell & 3/4”Single Cell Allocate a minimum distance of 5/8” from the center of screw hole to the edge of the wall and align the center of screw hole 1” away from the wall as the following picture. Use two M3.8x38mm screws to fasten the L bracket. Finally, align the cover with the notch of the base and
Head rail End cap Blanket Bottom rail Cord Equalizer Housing Cover
Installation Instructions
Honeycomb Shades Corded / Corded TDBU / Corded Day & Night
Hardware Standard Quantity Order Width (X) Installation Bracket Hold Down Bracket (Optional) Cord Cleat Spacer Block (Optional)
Getting Started Remove shade from package. Save packaging until shade is installed and working to your satisfaction.
Tools Needed: Power drill and drill bit Measuring tape Screwdriver Level Pencil
8 ½"≦X≦42 42"＜X≦75" X＞75" 2
3
4
2
2
2
1pc for Corded, 2pcs for Corded TDBU & Day & Night 2
3
4
2" Screw for Installation 4 6 8 Bracket with spacer 1 1/4" Screw for 3/8”S 2 3 4 Installation Bracket 1 1/4" Screw for 3/4”S &3/8”D 4 6 8 Installation Bracket 3/4" Screw for Hold Down Hold Down Bracket qty*2 + Cord Cleat qty Bracket/ Cord Cleat Note: for 3/8”D & 3/4”S shade, Optional flat head screws included. Use as needed.
Step 1: Bracket Installation
You will need to use the following fasteners for your particular mounting surface. Surface
b. for 3/8” Single cell
Measure 3” from both ends of the head rail. Mark the bracket location on the mounting surface Proper alignment of brackets will make installation easier.
3''
Space Evenly Space Evenly
3''
Lower
Allocate a min. distance of 5/16” from the edge of the wall to the front of brackets. Use one 1 1/4” mounting screws to secure brackets.
1
3/16"
Position the shade so that the front is facing you. Insert the rail with an angle facing the window; hooking up with the bracket front side, and then push it upward to snap into the bracket. For proper installation, start with attaching the front rail to the bracket.
Check Component/Hardware:
Installation Bracket Installation Bracket (for 3/4” S(left) & 3/8”D(right)) (for 3/8” S)
Cord Cleat
Hold Down bracket (optional)
a. for 3/8” Double cell & 3/4” Single cell [ Inside Mount ]
Floor
Step 3: How to Install Hold Down Brackets (optional)
' /16'
3
Step 4: Shade Operation
[ Outside Mount ] Allocate a min. distance of 5/16’’ from the end of brackets to the top window frame. Use two 1 1/4’’ mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.
Install the cord cleat on the wall. Wrap the operating cords around the cord cleat for child safety. Always use the cord cleat to keep cords out of the reach of children. The cleat should be installed more than 64” (1.6m) from the door.
Use two 3/4” screws to secure each hold down bracket.
Allocate a min. distance of 3/16’’ from wall to the front of brackets.Use two 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall. (Align the front of brackets flush with wall if only lock the back hole in the brackets.)
'
Metal
Sheet Metal Screws (Not Provided)
Installation Brackets
5/16'
Wall Anchors, Expansion Bolts Drywall/Plaster (Not Provided)
Lock
WARNING
for 3/8”S
3/4” Screws (Provide)
1
Step 2: Shade Installation
1 1/4” Screws (Provide)
Wood
Raise
Step 5: Cord Cleat
Fastener
for 3/8”D & 3/4”S
2
Unlock
[ Outside Mount ] Allocate a minimum distance of 3/16” from the end of brackets to the top window frame. Use one 1 1/4” mounting screws to attach each bracket.
2
5/16”
[ Inside Mount ]
64" (1.6m)
N300473-A 65101-11725-B
For Corded TDBU & Day & Night: when lowering the shade, lower the bottom rail first and then middle rail. When raising the shade, raise the middle rail first and then bottom rail. For Corded: operate as below illustration, according to the location of cord lock.
Young children can STRANGLE in cord and bead chain loops. They can also wrap cords around their necks and STRANGLE. Always keep cords out of children's reach. Move cribs, playpens, and other furniture away from cords and bead chains. hildren can climb furniture to get to cords.
C Always wrap the cords around the cleats in a figure eight, up high, out of reach of children.
MISE EN GARDE Un jeune enfant peut s'ÉTRANGLER avec la boucle d'un cordon ou d'une chanette. Il peut aussi
Safety Warning
Cleaning
Troubleshooting
Warning! Children can become entangled and strangle in window shade cords. Keep all cords out of reach from children. Move cribs and other furniture away from window coverings with cords.The following devices are recommended: ! WARNING Cord cleat (included) Young children can be Clip/Clamp e n t a n g l e da n d strangled in cords. Tie the cord to itself Keep all cords out of children’s reach. Cord Use any tie-down device
Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).
cleat is provided and should be used.
enrouler le cordon autour de son cou et
ÉTRANGLER. Gardez toujours les cordons hors de portée des enfants. Éloignez les lits et parcs de bébé, ainsi que toute autre pièce de mobilier, des cordons et des chaînettes. Un enfant
Problem
Solution
For corded TDBU & Day & Night, if the bottom shade fabric not remain stacked (billowed on the windowsill), when the top was lowered
When lower the bottom shade, please pull the left side cord leftwards to lock the bottom rail. Please make sure the bottom rail is locked right above the windowsill first (if not locked, please try more times) before operating the top shade.
s'
peut grimper sur un meuble pour atteindre les cordons.
Enroulez toujours les cordons en noeud en huit autour du
taquet de cordon, placé haut et hors de portée des enfants.
ADVERTENCIA
MISE EN GARDE
3" o menos
76mm (3 po) o menos
Remove the Shade For Corded, Fully raise the shade For Corded TDBU & Day & Night, Lower the mid rail Insert screwdriver into the gap between the back of the rail and the bracket. Gently maneuver the screwdriver toward yourself to pry the bracket.
3" or less
Inner cords can pull out to form a loop, which can strangle a young child.
How to Reassemble Ellipse Safety Cord Connector
Inner cord stop devices can reduce this risk if positioned correctly on the operating cords.
If inner cord stop devices are more Our Shade comes equipped with an Ellipse Safety Cord Connector that prevents child strangulation. If the device comes apart, please refer to below steps: 1. Open the Ellipse Safety Cord Connector entirely. 2. Align all cords and slide them into the slot of Ellipse Safety Cord Connector (the slot should be the side in round circle); 3. Close the Ellipse Safety Cord Connector; 4. Pull the tassel cords and make sure it is closed tightly. Note: the transparent bead should be exposed at the top of Ellipse Safety Cord Connector.
than 3" (76 mm) below the headrail when the blind is fully lowered, move them closer by following the inner cord stop device adjustment instructions.
Las cuerdas internas pueden sacarse para formar un lazo en que puede ESTRANGULARSE un niño pequeño. Los dispositivos de paro de la cuerda interna pueden diminuir este riesgo si están situados correctamente en el halado de las cuerdas. Si los dispositivos de paro de cuerda interna son más de 3 pulgadas (76 mm) por debajo del riel superior cuando está bajada ompletamente la persiana, muévalos siguiendo las instrucciones del ajuste de paro de cuerda interna.
Les cordons intérieurs peuvent sortir
pour former une boucle et ÉTRANGLER un jeune enfant. Les dispositifs d’arrêt des cordons intérieurs peuvent diminuer ce risque s’ils sont placés correctement sur les cordons.
Si les dispositifs d’arrêt des cordons sont situés à plus de 76 mm (3 po) en store est complètement baissé, rapprochez-les en suivant les instructions de réglage du dispositif d’arrêt du cordon intérieur.
N300474-A N300474-A 65101-11726 65101-11726-A
Installation Instructions Honeycomb Shades
Cordless & Cordless TDBU & Cordless Day&Night
Hardware Standard Quantity Order Width (X) Installation Bracket Handle Hold Down Bracket (Optional) Spacer (Optional) 1 1/4" Screw for Installation Bracket 2" Screw for Installation Bracket with spacer 3/4" Screw for Hold Down Bracket
Getting Started Remove shade from package. Save packaging until shade is installed and working to your satisfaction.
Level Measuring Tape Pencil Power drill (¼” hex driver and drill bit) Screwdriver
3
4
5
2
2
2
2
Fastener #8 1 1/4” Screws (Provide)
Check Component/Hardware:
For corded, fully raise the shade. For TDBU & Day & Night, Lower the middle rail. Gently pry the bracket off the head rail with a flat screwdriver as below picture.
For proper installation, start with attaching the front rail to the bracket.
4
6
8
10
4
6
8
10
4
4
4
4
Space Evenly Space Evenly
For Cordless, align wall to the front of brackets. For Cordless TDBU & Day & Night, allocate a min. distance of 1/16” from wall to the front of brackets. Use two #8 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall. (Cordless TDBU / Day & Night)
6''
1/1
[ Outside Mount ] Align the end of brackets with the top window frame. Use two #8 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall. (Cordless)
Step 3: How to Install Shade Handle Slide the handle onto the plastic piece pre-attached to the rails.
Step 4: Shade Operation
(Cordless TDBU / Day & Night)
Cleaning the Shade Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).
Troubleshooting
3''
[ Inside Mount ]
(Cordless)
Remove the shade
1pc for extend distance 10mm 2pcs for extend distance 18mm
Wall Anchors, Expansion Bolts Drywall/Plaster (Not Provided) Sheet Metal Screws (Not Provided)
Position head rail at an angle so that it is hooked to the front of the bracket. Then push it upward to snap into the bracket.
Step 1: Bracket Installation
#6 3/4” Screws
Metal
Remove the Shade
Note: Optional flat head screws included. Use as needed.
3''
You will need to use the following fasteners for your particular mounting surface.
Wood
2
1pcs for X≦50", 2pcs for X>50" (Cordless) 2pcs for X≦50", 4pcs for X>50" (Cordless TDBU & Day & Night)
Measure 3” from both ends of the head rail. Mark the bracket location on the mounting surface
Tools Needed:
Surface
X≦39" 39"<X≦66" 66"<X≦93" 93"<X≦120"
Step 2: Shade Installation
1/2
1/2
1/3
1/3
1/3
To lower the shade, gently pull down the shade on the bottom rail handle and stop at the desired location. For TDBU & Day & Night, pull down the bottom rail first before lowering the midle rail. To raise the shade, gently raise the shade on the bottom rail handle to desired height. For TDBU & Day & Night, if the shade will not lift, pull the midrail down fully to the bottom first and then raise the bottom rail together with midrail up. Do not grasp the rail unevenly. Always lower or raise the shade in the middle or use both hands with even pressure to two handles of the rail.
Problem The shade will not snap into the mounting brackets
Solution Check if mounting brackets are aligned. Refer to Step 1.
Gently pull down on the bottom rail to reactivate the cordless mechanism. Repeat if necessary. The shade will not lift For TDBU & Day&Night, pull the midrail down fully to the bottom first and then raise the bottom rail together with midrail up. The shade stack up unevenly
Bracket
Lower the shade completely, then raise it up to correct it. Repeat if necessary.
Head rail Middle rail
Step 5: How to Install Hold Down Brackets (optional) Use #6 3/4” screw to secure each bracket.
Blanket Bottom rail Handle
Installation Bracket
Hold Down bracket (optional)
Hold Down Bracket
N300475-A 65101-11727-C
Step 2: Shade Installation z
Installation Instructions
Order Width (X)
Honeycomb Shades Continuous Cordloop
Installation Bracket Hold Down Bracket (Optional) Spacer Block(Optional) 2" Screw for Installation Bracket with spacer block M3.8x51mm screw for Tensioner 1 1/4" Screw for Installation Bracket 3/4" Screw for Hold Down Bracket
93"＜ X 39"＜X 66"＜X ≦ X≦ ≦66" ≦93" 39" 120" 2 3 4 5 2
2
2
4
6
8
2
Remove the Shade
1
d
2
2
2
2
4
6
8
10
4
4
4
4
Step 1: Bracket Installation Measure 3” from both ends of the head rail. Mark bracket location on the mounting surface. Space Evenly
3”
x Make sure the cord is tightened / taut without stretching, twisting or crossing, and the tensioner and control cord does not interfere with raising or lowering the shade before cord tensioner is mounted. x Use 2pcs M3.8x51mm screws to mount the cord x tensioner to the wall or window frame firmly for both inside & outside mount. Please refer to the following steps: Step 2 Step 1
Inside Mount
z
Surface
Wood
Fastener
Allocate a min. distance of 1/16’’ from wall to the front of brackets as below drawing. Use two #8 1 1/4 ” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.
Step 3
#8 1 1/4” Screws (Provided) M3.8x51mm screws #6 3/4” screws
Drywall/Plaster Metal
Wall Anchors, Expansion Bolts (Not Provide) Sheet Metal Screws (Not Provide)
Outside Mount z
z
Check Component/Hardware:
Installation Bracket
Hold Down Bracket (Optional)
Allocate a min. distance of 5/8’’ from wall to the bottom of brackets as below drawing. Use two #8 1 1/4 ”mounting screws to attach each bracket. Use wall anchors for drywall or plaster wall.
Fully raise the shade. Gently pry the bracket off the head rail with a flat screwdriver. Remove the shade.
c
Step 3: Cord Tensioner Installation
Tools:
Installation Screws
z
z
Remove shade from package. Save packaging until shade is installed and working to your satisfaction.
z
z
10
Getting Started
x Power drill x Tape measure x Screwdriver x Level x Pencil
x Pull cord to operate shade. Cord Tensioner must be fully tightened prior to operating the shade.
For proper installation, start with attaching the front rail to the bracket.
1pc for extend distance 10mm 2pcs for extend distance 18mm
Note: Optional flat head screw included. Use as needed.
3”
Position head rail at an angle so that it is hooked to the front of the bracket. Then push it upward to snap into the bracket.
Step 4: How to Install Hold Down Brackets (optional) z
Use #6 3/4” screw to secure each bracket.
Step 5: Shade Operation
d
Note x Keep away from heat, sparks and open flame. x Larger windows may require two people to install. x Proper In the process of installation, must support the shade firmly to avoid it fall down too quick to damage the people or itself. x Operate shade only by pulling the cord. x To ensure child safety, install cord cleat and tighten up any loose cords after the shade is installed
Cleaning Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).
N300476 65101-11728
52”<X72”, 4 M3.5×25mm Screw (for Base, M3.5×25mm Screw (for Base, 3/4”S & 3/8”D, Inside Mount)
M3.8x38mm screw (for Wall Mount)
L bracket qty*2 2
base on L bracket, Wall Mount)
Mount)
3/8” Single
3/8”Double & 3/4”Single with Rail Cover
Getting Started Remove the shade from the package. Save the packaging until the shade is installed and working to your satisfaction.
Wood
Bracket Installation
Handle Installation
Inside Mount – for 3/8”Single Cell For flush mount, the minimum distance from the top/bottom wall to the base side is 1/4” and 1/8” from the side wall to the edge of Base. Use M3.5×25mm Screw to secure the base. Align the cover with the notch of the base and push the cover in toward the wall.
Slide the handle onto the plastic piece pre-attached to the rails.
notch 1/4” Base 1/8” step1
step 2 (Top)
You will need to use the following fasteners for your particular mounting surface. Surface
1pc to extend distance 10mm 2pcs to extend distance 18mm
Cover
Tools Needed： x Power drill and drill bit x Measuring tape x Screwdriver x Level x Pencil
Fastener M3.5×25mm Screws (Provided)
M3.8×38mm Wall Anchors, Expansion Bolts Drywall/Plaster (Not Provided) Sheet Metal Screws Metal (Not Provided)
(for 3/8” Single)
L Bracket for windows with marble sill (Optional) (for 3/8”S) L bracket (for 3/4”Single & 3/8”Doubld, Wall Mount)
Step 2
Step1
Notes For child safety, please check and ensure that there are no loose cords after the shade is completely installed. Please also make sure that cords are nice and tight and not tangled.
9
step3
2
Cleaning
Inside Mount – for 3/8” Double Cell & 3/4”Single Cell For flush mount TOP, the minimum distance from the left/right side wall to the end of rail cover is 1/8” and the distance from the center of screw hole to edge of wall is A (A=1 1/16” for 3/8”D & A=1 1/4” for 3/4”S). Use M3.5×25mm Screw to secure the rail cover. Align the cover with the notch of the base and push the cover in toward the wall.
Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!). Cord Equalizer Housing Base
X≦50" 2
X>50" 4
4
7
Cord Equalizer Housing Base (for 3/4”Single & 3/8”Double) L Bracket (for 3/8”S, Wall Mount)
(Top View) Outside Mount – for 3/8”Single Cell Allocate a minimum distance of 3/8” from top window opening to the L bracket and align L bracket 1/16” away from shade end. Use two M3.8x38mm screws to fasten the L bracket. Once the L bracket is installed, use one M3 x 3.6mm bolt to attach base. Finally, align the cover with the notch of the base and push the cover in, as shown in “Inside Mount” illustration. (Top)
5/16''
Hardware Order Width (X) Handle Cord Equalizer Housing Base
(Bottom) Install the bracket similar to previous step but in reverse. Use one M3 x 3.6mm bolt to attach base.
8.5”<X≦40”, 4 40”<X≦52”, 5 52”<X72”, 6
M3 x 3.6mm Bolt (for locking Spacer Block (Optional, Wall
Side mount L bracket for windows with marble sill (optional for 3/8”Single) Allocate a distance of 1/4” from bottom corner window frame and use two M3.8×38mm screws to secure the L bracket. Use one M3 x 3.6mm bolt to attach base to the L bracket (through inner screw hole)
4
3/8” S, Inside Mount)
Honeycomb Shades SmartFitTM
push the cover in, as shown in “Inside Mount” illustration.
5/8''
Installation Instructions
Align the cover with the notch of the base and push the cover in toward the wall.
(Bottom View)
2 4
7
2
2
8.5”<X≦ 40”, 2 40”<X≦ 52”, 3
For flush mount BOTTOM, the minimum distance from the bottom wall to the base side is 1/8” and the distance from the edge of wall to the center of the screw hole is A (A=11/16” for 3/8”D & A=7/8” for 3/4”S). Use M3.5×25mm Screw to secure the base.
(Bottom) Install the bracket similar to top steps but in reverse way. Outside Mount – for 3/8”Double Cell & 3/4”Single Cell Allocate a minimum distance of 5/8” from the center of screw hole to the edge of the wall and align the center of screw hole 1” away from the wall as the following picture. Use two M3.8x38mm screws to fasten the L bracket. Finally, align the cover with the notch of the base and
Head rail End cap Blanket Bottom rail Cord Equalizer Housing Cover
Installation Instructions
Honeycomb Shades Corded / Corded TDBU / Corded Day & Night
Hardware Standard Quantity Order Width (X) Installation Bracket Hold Down Bracket (Optional) Cord Cleat Spacer Block (Optional)
Getting Started Remove shade from package. Save packaging until shade is installed and working to your satisfaction.
Tools Needed: Power drill and drill bit Measuring tape Screwdriver Level Pencil
8 ½"≦X≦42 42"＜X≦75" X＞75" 2
3
4
2
2
2
1pc for Corded, 2pcs for Corded TDBU & Day & Night 2
3
4
2" Screw for Installation 4 6 8 Bracket with spacer 1 1/4" Screw for 3/8”S 2 3 4 Installation Bracket 1 1/4" Screw for 3/4”S &3/8”D 4 6 8 Installation Bracket 3/4" Screw for Hold Down Hold Down Bracket qty*2 + Cord Cleat qty Bracket/ Cord Cleat Note: for 3/8”D & 3/4”S shade, Optional flat head screws included. Use as needed.
Step 1: Bracket Installation
You will need to use the following fasteners for your particular mounting surface. Surface
b. for 3/8” Single cell
Measure 3” from both ends of the head rail. Mark the bracket location on the mounting surface Proper alignment of brackets will make installation easier.
3''
Space Evenly Space Evenly
3''
Lower
Allocate a min. distance of 5/16” from the edge of the wall to the front of brackets. Use one 1 1/4” mounting screws to secure brackets.
1
3/16"
Position the shade so that the front is facing you. Insert the rail with an angle facing the window; hooking up with the bracket front side, and then push it upward to snap into the bracket. For proper installation, start with attaching the front rail to the bracket.
Check Component/Hardware:
Installation Bracket Installation Bracket (for 3/4” S(left) & 3/8”D(right)) (for 3/8” S)
Cord Cleat
Hold Down bracket (optional)
a. for 3/8” Double cell & 3/4” Single cell [ Inside Mount ]
Floor
Step 3: How to Install Hold Down Brackets (optional)
' /16'
3
Step 4: Shade Operation
[ Outside Mount ] Allocate a min. distance of 5/16’’ from the end of brackets to the top window frame. Use two 1 1/4’’ mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.
Install the cord cleat on the wall. Wrap the operating cords around the cord cleat for child safety. Always use the cord cleat to keep cords out of the reach of children. The cleat should be installed more than 64” (1.6m) from the door.
Use two 3/4” screws to secure each hold down bracket.
Allocate a min. distance of 3/16’’ from wall to the front of brackets.Use two 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall. (Align the front of brackets flush with wall if only lock the back hole in the brackets.)
'
Metal
Sheet Metal Screws (Not Provided)
Installation Brackets
5/16'
Wall Anchors, Expansion Bolts Drywall/Plaster (Not Provided)
Lock
WARNING
for 3/8”S
3/4” Screws (Provide)
1
Step 2: Shade Installation
1 1/4” Screws (Provide)
Wood
Raise
Step 5: Cord Cleat
Fastener
for 3/8”D & 3/4”S
2
Unlock
[ Outside Mount ] Allocate a minimum distance of 3/16” from the end of brackets to the top window frame. Use one 1 1/4” mounting screws to attach each bracket.
2
5/16”
[ Inside Mount ]
64" (1.6m)
N300473-A 65101-11725-B
For Corded TDBU & Day & Night: when lowering the shade, lower the bottom rail first and then middle rail. When raising the shade, raise the middle rail first and then bottom rail. For Corded: operate as below illustration, according to the location of cord lock.
Young children can STRANGLE in cord and bead chain loops. They can also wrap cords around their necks and STRANGLE. Always keep cords out of children's reach. Move cribs, playpens, and other furniture away from cords and bead chains. hildren can climb furniture to get to cords.
C Always wrap the cords around the cleats in a figure eight, up high, out of reach of children.
MISE EN GARDE Un jeune enfant peut s'ÉTRANGLER avec la boucle d'un cordon ou d'une chanette. Il peut aussi
Safety Warning
Cleaning
Troubleshooting
Warning! Children can become entangled and strangle in window shade cords. Keep all cords out of reach from children. Move cribs and other furniture away from window coverings with cords.The following devices are recommended: ! WARNING Cord cleat (included) Young children can be Clip/Clamp e n t a n g l e da n d strangled in cords. Tie the cord to itself Keep all cords out of children’s reach. Cord Use any tie-down device
Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).
cleat is provided and should be used.
enrouler le cordon autour de son cou et
ÉTRANGLER. Gardez toujours les cordons hors de portée des enfants. Éloignez les lits et parcs de bébé, ainsi que toute autre pièce de mobilier, des cordons et des chaînettes. Un enfant
Problem
Solution
For corded TDBU & Day & Night, if the bottom shade fabric not remain stacked (billowed on the windowsill), when the top was lowered
When lower the bottom shade, please pull the left side cord leftwards to lock the bottom rail. Please make sure the bottom rail is locked right above the windowsill first (if not locked, please try more times) before operating the top shade.
s'
peut grimper sur un meuble pour atteindre les cordons.
Enroulez toujours les cordons en noeud en huit autour du
taquet de cordon, placé haut et hors de portée des enfants.
ADVERTENCIA
MISE EN GARDE
3" o menos
76mm (3 po) o menos
Remove the Shade For Corded, Fully raise the shade For Corded TDBU & Day & Night, Lower the mid rail Insert screwdriver into the gap between the back of the rail and the bracket. Gently maneuver the screwdriver toward yourself to pry the bracket.
3" or less
Inner cords can pull out to form a loop, which can strangle a young child.
How to Reassemble Ellipse Safety Cord Connector
Inner cord stop devices can reduce this risk if positioned correctly on the operating cords.
If inner cord stop devices are more Our Shade comes equipped with an Ellipse Safety Cord Connector that prevents child strangulation. If the device comes apart, please refer to below steps: 1. Open the Ellipse Safety Cord Connector entirely. 2. Align all cords and slide them into the slot of Ellipse Safety Cord Connector (the slot should be the side in round circle); 3. Close the Ellipse Safety Cord Connector; 4. Pull the tassel cords and make sure it is closed tightly. Note: the transparent bead should be exposed at the top of Ellipse Safety Cord Connector.
than 3" (76 mm) below the headrail when the blind is fully lowered, move them closer by following the inner cord stop device adjustment instructions.
Las cuerdas internas pueden sacarse para formar un lazo en que puede ESTRANGULARSE un niño pequeño. Los dispositivos de paro de la cuerda interna pueden diminuir este riesgo si están situados correctamente en el halado de las cuerdas. Si los dispositivos de paro de cuerda interna son más de 3 pulgadas (76 mm) por debajo del riel superior cuando está bajada ompletamente la persiana, muévalos siguiendo las instrucciones del ajuste de paro de cuerda interna.
Les cordons intérieurs peuvent sortir
pour former une boucle et ÉTRANGLER un jeune enfant. Les dispositifs d’arrêt des cordons intérieurs peuvent diminuer ce risque s’ils sont placés correctement sur les cordons.
Si les dispositifs d’arrêt des cordons sont situés à plus de 76 mm (3 po) en store est complètement baissé, rapprochez-les en suivant les instructions de réglage du dispositif d’arrêt du cordon intérieur.
N300474-A N300474-A 65101-11726 65101-11726-A
Installation Instructions Honeycomb Shades
Cordless & Cordless TDBU & Cordless Day&Night
Hardware Standard Quantity Order Width (X) Installation Bracket Handle Hold Down Bracket (Optional) Spacer (Optional) 1 1/4" Screw for Installation Bracket 2" Screw for Installation Bracket with spacer 3/4" Screw for Hold Down Bracket
Getting Started Remove shade from package. Save packaging until shade is installed and working to your satisfaction.
Level Measuring Tape Pencil Power drill (¼” hex driver and drill bit) Screwdriver
3
4
5
2
2
2
2
Fastener #8 1 1/4” Screws (Provide)
Check Component/Hardware:
For corded, fully raise the shade. For TDBU & Day & Night, Lower the middle rail. Gently pry the bracket off the head rail with a flat screwdriver as below picture.
For proper installation, start with attaching the front rail to the bracket.
4
6
8
10
4
6
8
10
4
4
4
4
Space Evenly Space Evenly
For Cordless, align wall to the front of brackets. For Cordless TDBU & Day & Night, allocate a min. distance of 1/16” from wall to the front of brackets. Use two #8 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall. (Cordless TDBU / Day & Night)
6''
1/1
[ Outside Mount ] Align the end of brackets with the top window frame. Use two #8 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall. (Cordless)
Step 3: How to Install Shade Handle Slide the handle onto the plastic piece pre-attached to the rails.
Step 4: Shade Operation
(Cordless TDBU / Day & Night)
Cleaning the Shade Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).
Troubleshooting
3''
[ Inside Mount ]
(Cordless)
Remove the shade
1pc for extend distance 10mm 2pcs for extend distance 18mm
Wall Anchors, Expansion Bolts Drywall/Plaster (Not Provided) Sheet Metal Screws (Not Provided)
Position head rail at an angle so that it is hooked to the front of the bracket. Then push it upward to snap into the bracket.
Step 1: Bracket Installation
#6 3/4” Screws
Metal
Remove the Shade
Note: Optional flat head screws included. Use as needed.
3''
You will need to use the following fasteners for your particular mounting surface.
Wood
2
1pcs for X≦50", 2pcs for X>50" (Cordless) 2pcs for X≦50", 4pcs for X>50" (Cordless TDBU & Day & Night)
Measure 3” from both ends of the head rail. Mark the bracket location on the mounting surface
Tools Needed:
Surface
X≦39" 39"<X≦66" 66"<X≦93" 93"<X≦120"
Step 2: Shade Installation
1/2
1/2
1/3
1/3
1/3
To lower the shade, gently pull down the shade on the bottom rail handle and stop at the desired location. For TDBU & Day & Night, pull down the bottom rail first before lowering the midle rail. To raise the shade, gently raise the shade on the bottom rail handle to desired height. For TDBU & Day & Night, if the shade will not lift, pull the midrail down fully to the bottom first and then raise the bottom rail together with midrail up. Do not grasp the rail unevenly. Always lower or raise the shade in the middle or use both hands with even pressure to two handles of the rail.
Problem The shade will not snap into the mounting brackets
Solution Check if mounting brackets are aligned. Refer to Step 1.
Gently pull down on the bottom rail to reactivate the cordless mechanism. Repeat if necessary. The shade will not lift For TDBU & Day&Night, pull the midrail down fully to the bottom first and then raise the bottom rail together with midrail up. The shade stack up unevenly
Bracket
Lower the shade completely, then raise it up to correct it. Repeat if necessary.
Head rail Middle rail
Step 5: How to Install Hold Down Brackets (optional) Use #6 3/4” screw to secure each bracket.
Blanket Bottom rail Handle
Installation Bracket
Hold Down bracket (optional)
Hold Down Bracket
