Installation Instructions - Panduit
Panduct PanelMax Shielded Wiring Duct For Use with Type C Cover and Compatible with Panduct PanelMax Noise Shield and Panduct Divider Walls Part Numbers: G2X2LG6EMI, G2X3LG6EMI, G2X4LG6EMI
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2011
EP001
Cutting Shielded Wiring Duct to Required Length 1.
2.
2" max G2X2LG6EMI G2X3LG6EMI G2X4LG6EMI
CWST
CWST Wire Snipping Tool (sold separately)
Remove from both sides
DCT Duct Cutting Tool (sold separately)
DCT
Surface Preparation for Good Electrical Bond 3.
Anti-Oxidizing Compound
1"
Control panel surface
Screw
2" Remove paint to bare metal
Repeat for each screw location at duct ends and/or T-intersection
Anti-Oxidizing Compound
Installing One Shielded Wiring Duct 4A. Screw or NR-1 Rivet
- OR -
2" max
(sold separately)
10-32 x 1/2" Screws (or sheet metal screw equivalent) to be supplied by the installer or end user
2" max
Prepared surfaces (see step 3)
Control panel surface
Screws
NR1-C, NR1-M Rivet (sold separately)
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 1 of 2
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2011
EP001
Installing Two Shielded Wiring Duct in a T-intersection Screw or NR-1 Rivet (sold separately)
- OR -
10-32 x 1/2" Screws (or sheet metal screw equivalent) to be supplied by the installer or end user
Duct #2
4B.
Sidewall breakout
2" max
2" max
(Remove section 2-3 finger wide as needed)
Control panel surface
Align screws
Duct #1
Prepared surfaces (see step 3)
Screws
NR1-C, NR1-M Rivet (sold separately)
Optional - Sidewall Breakout for Creating T-intersection 2.
1.
DNT-100
3.
CWST Wire Snipping Tool (sold separately)
CWST
DNT-100 Duct Notching Tool (sold separately)
Optional - Sidewall Finger Removal 2.
1. Remove Only As Required
CAUTION Foil edges may be sharp.
Removing bridge connectors between fingers will reduce local noice reduction capability.
For Use of Panduct PanelMax Noise Shield (SD2EMI, SD3EMI, SD4EMI) with Panduct PanelMax Shielded Wiring Duct, Reference Installation Instructions RW260 E-mail: [email protected]
For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp
www.panduit.com Page 2 of 2
Fax: (815) 328-2001
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2011
EP001
Cutting Shielded Wiring Duct to Required Length 1.
2.
2" max G2X2LG6EMI G2X3LG6EMI G2X4LG6EMI
CWST
CWST Wire Snipping Tool (sold separately)
Remove from both sides
DCT Duct Cutting Tool (sold separately)
DCT
Surface Preparation for Good Electrical Bond 3.
Anti-Oxidizing Compound
1"
Control panel surface
Screw
2" Remove paint to bare metal
Repeat for each screw location at duct ends and/or T-intersection
Anti-Oxidizing Compound
Installing One Shielded Wiring Duct 4A. Screw or NR-1 Rivet
- OR -
2" max
(sold separately)
10-32 x 1/2" Screws (or sheet metal screw equivalent) to be supplied by the installer or end user
2" max
Prepared surfaces (see step 3)
Control panel surface
Screws
NR1-C, NR1-M Rivet (sold separately)
For Technical Support: www.panduit.com/resources/install_maintain.asp Page 1 of 2
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2011
EP001
Installing Two Shielded Wiring Duct in a T-intersection Screw or NR-1 Rivet (sold separately)
- OR -
10-32 x 1/2" Screws (or sheet metal screw equivalent) to be supplied by the installer or end user
Duct #2
4B.
Sidewall breakout
2" max
2" max
(Remove section 2-3 finger wide as needed)
Control panel surface
Align screws
Duct #1
Prepared surfaces (see step 3)
Screws
NR1-C, NR1-M Rivet (sold separately)
Optional - Sidewall Breakout for Creating T-intersection 2.
1.
DNT-100
3.
CWST Wire Snipping Tool (sold separately)
CWST
DNT-100 Duct Notching Tool (sold separately)
Optional - Sidewall Finger Removal 2.
1. Remove Only As Required
CAUTION Foil edges may be sharp.
Removing bridge connectors between fingers will reduce local noice reduction capability.
For Use of Panduct PanelMax Noise Shield (SD2EMI, SD3EMI, SD4EMI) with Panduct PanelMax Shielded Wiring Duct, Reference Installation Instructions RW260 E-mail: [email protected]
For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp
www.panduit.com Page 2 of 2
Fax: (815) 328-2001
