Instructions - RAB Lighting
FFLED18 EMERGENCY INSTALLATION SHEET
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: [email protected]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF and batteries are disconnected before installing or maintaining fixture. No user serviceable parts inside.
Mounting
CAUTION: Suitable as Wet Locations as Wall Mount. 1. Loosen and remove (4) Screws and separate Back Box from Emergency Housing. Use provided tether.
Gasket
Screws
Housing
2. Drill necessary holes on Back Box. Measurements of drill positions are shown below. 3. Match the hole pattern and place the Gasket on the Back Box. 4. Secure the Back Box on the surface with hardware appropriate for the mounting surface. 5. Wire the fixture to the incoming supply wires according to NEC and local codes. Use UL listed wire connectors. 6. For FFLED18/E, each battery unit has one connector. For FFLED18/EC, each battery unit has two connectors as shown below. For details refer to the appropriate Wiring Diagram section and supplied Instruction Sheet.
Back Box
Housing Gasket
Screws
Emergency Batteries
7. Connect the battery connectors. Do not connect the Batteries before wiring the fixture to the supply.
Bracket Screw
8. Secure Housing to Back Box. Check Housing Gasket seal all around. 9. Apply sealant to all unused conduit entry points. To ensure weatherproof seal, apply weatherproof silicone sealant around the edge where the fixture meets the wall. Seal arm thread using teflon tape or silicone sealant.
Bracket
Two connectors for FFLED18/EC
FFLED18/E Battery Connector
FFLED18 EMERGENCY INSTALLATION SHEET CLEANING & MAINTENANCE
DRILL TEMPLATE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
7.5” 7.500 [190,5]
3.75” 3.750 [95,25]
1. Clean glass lens & fixture with non-abrasive glass cleaning solution. 2. Do not open fixture to clean the LED. Do not touch the LED.
0.6”
.600 [15,24]
2.94” 2.940 [74,68]
US: Pat. D643,147; CN: ZL201130171304.1; MX: pending; TW: Pat. pending; CA: D RAB Lighting Inc. Patent Pending.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
FFLED18/E WIRING DIAGRAM
(Refer to next page for FFLED18/EC wiring diagram)
BATTERY 1
RED
BATTERY 2
RED
WHITE
WHITE
CUSTOMER SHOULD CONNECT ONLY AFTER FINISHING WIRING TO AC POWER. BATTERY COULD HAVE CHARGE & SHOCK
RAB LABEL - ADD
BLACK
SWITCHED HOT FUSE HOLDER
RAB LABEL - ADD
BLACK
BROWN
BODINE BSL722 LED EMERGENCY DRIVER
WHITE
WHITE
WHITE
LABEL PROVIDED
RED-WHITE STRIPE
WHITE - RED STRIPE
LEAVE OPEN
WHITE DO NOT CONNECT
DURING RED MANUFACTURING
RED-WHITE STRIPE
BLACK
UNSWITCHED HOT
RED
BLACK
BLACK
EMERGENCY HOUSING
BLUE
CHARGING INDICATOR LIGHT / TEST SWITCH
RED
VIOLET GREY
BLACK
GREY
CHARGING INDICATOR/ TEST SWITCH
BLACK
YELLOW
WHITE/BLACK
YELLOW - BLACK STRIPE WHITE
COM
RED BLACK
AC DRIVER WHITE
BLACK RED BLACK
RED
BLUE
RED BLACK
GROUND
FFLED18
FFLED18 (3X6) EMERGENCY 120V OR 277V WIRING DIAGRAM
KS
2.22.12 LED18W EMERGENCY 120V OR 277V WIRING
FFLED18 EMERGENCY INSTALLATION SHEET FFLED18/EC WIRING DIAGRAM
(Refer to previous page for FFLED18/E wiring diagram)
RED
RED
WHITE
BLACK
BLACK BLACK
SWITCHED HOT FUSE HOLDER
BAT 1
RED
BLUE/ORANGE
RED BAT 1
BAT 1
WHITE
RED
RED BAT 2
BAT 2
BLUE
BLACK
YELLOW/RED
RED-WHITE STRIPE
RED BAT 2
BAT 2
YELLOW/RED
RAB LABEL - ADD
WHITE - RED STRIPE
BLACK
UNSWITCHED HOT
BODINE BSL722 LED EMERGENCY DRIVER
WHITE
WHITE
LEAVE OPEN DO NOT CONNECT DURING MANUFACTURING
WHITE RED
BLUE
BATTERY 1
BATTERY 2
WHITE WHITE
BROWN
BLUE
VIOLET
RED
GREY
LABEL PROVIDED CHARGING INDICATOR LIGHT / TEST SWITCH
BLACK
CHARGING INDICATOR/ TEST SWITCH
BLACK
GREY WHITE/BLACK YELLOW - BLACK STRIPE
YELLOW
WHITE
COM
CUSTOMER SHOULD CONNECT ONLY AFTER FINISHING WIRING TO AC POWER. BATTERY COULD HAVE CHARGE & SHOCK
WHITE
YELLOW/RED
WHITE
RED-WHITE STRIPE
WHITE
BLUE/ORANGE
YELLOW/RED
RAB LABEL - ADD
BAT 1
EMERGENCY HOUSING
RED BLACK
AC DRIVER WHITE
BLACK RED BLACK
RED
BLUE
RED BLACK
GROUND
FFLED18
FFLED18 (3X6) EMERGENCY COLD 120V OR 277V WIRING DIAGRAM
FFLED18 EMG-IN-0412
KS
4.18.12 LED18W EMERGY COLD 120V OR 277V WIRING
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: [email protected]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF and batteries are disconnected before installing or maintaining fixture. No user serviceable parts inside.
Mounting
CAUTION: Suitable as Wet Locations as Wall Mount. 1. Loosen and remove (4) Screws and separate Back Box from Emergency Housing. Use provided tether.
Gasket
Screws
Housing
2. Drill necessary holes on Back Box. Measurements of drill positions are shown below. 3. Match the hole pattern and place the Gasket on the Back Box. 4. Secure the Back Box on the surface with hardware appropriate for the mounting surface. 5. Wire the fixture to the incoming supply wires according to NEC and local codes. Use UL listed wire connectors. 6. For FFLED18/E, each battery unit has one connector. For FFLED18/EC, each battery unit has two connectors as shown below. For details refer to the appropriate Wiring Diagram section and supplied Instruction Sheet.
Back Box
Housing Gasket
Screws
Emergency Batteries
7. Connect the battery connectors. Do not connect the Batteries before wiring the fixture to the supply.
Bracket Screw
8. Secure Housing to Back Box. Check Housing Gasket seal all around. 9. Apply sealant to all unused conduit entry points. To ensure weatherproof seal, apply weatherproof silicone sealant around the edge where the fixture meets the wall. Seal arm thread using teflon tape or silicone sealant.
Bracket
Two connectors for FFLED18/EC
FFLED18/E Battery Connector
FFLED18 EMERGENCY INSTALLATION SHEET CLEANING & MAINTENANCE
DRILL TEMPLATE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
7.5” 7.500 [190,5]
3.75” 3.750 [95,25]
1. Clean glass lens & fixture with non-abrasive glass cleaning solution. 2. Do not open fixture to clean the LED. Do not touch the LED.
0.6”
.600 [15,24]
2.94” 2.940 [74,68]
US: Pat. D643,147; CN: ZL201130171304.1; MX: pending; TW: Pat. pending; CA: D RAB Lighting Inc. Patent Pending.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
FFLED18/E WIRING DIAGRAM
(Refer to next page for FFLED18/EC wiring diagram)
BATTERY 1
RED
BATTERY 2
RED
WHITE
WHITE
CUSTOMER SHOULD CONNECT ONLY AFTER FINISHING WIRING TO AC POWER. BATTERY COULD HAVE CHARGE & SHOCK
RAB LABEL - ADD
BLACK
SWITCHED HOT FUSE HOLDER
RAB LABEL - ADD
BLACK
BROWN
BODINE BSL722 LED EMERGENCY DRIVER
WHITE
WHITE
WHITE
LABEL PROVIDED
RED-WHITE STRIPE
WHITE - RED STRIPE
LEAVE OPEN
WHITE DO NOT CONNECT
DURING RED MANUFACTURING
RED-WHITE STRIPE
BLACK
UNSWITCHED HOT
RED
BLACK
BLACK
EMERGENCY HOUSING
BLUE
CHARGING INDICATOR LIGHT / TEST SWITCH
RED
VIOLET GREY
BLACK
GREY
CHARGING INDICATOR/ TEST SWITCH
BLACK
YELLOW
WHITE/BLACK
YELLOW - BLACK STRIPE WHITE
COM
RED BLACK
AC DRIVER WHITE
BLACK RED BLACK
RED
BLUE
RED BLACK
GROUND
FFLED18
FFLED18 (3X6) EMERGENCY 120V OR 277V WIRING DIAGRAM
KS
2.22.12 LED18W EMERGENCY 120V OR 277V WIRING
FFLED18 EMERGENCY INSTALLATION SHEET FFLED18/EC WIRING DIAGRAM
(Refer to previous page for FFLED18/E wiring diagram)
RED
RED
WHITE
BLACK
BLACK BLACK
SWITCHED HOT FUSE HOLDER
BAT 1
RED
BLUE/ORANGE
RED BAT 1
BAT 1
WHITE
RED
RED BAT 2
BAT 2
BLUE
BLACK
YELLOW/RED
RED-WHITE STRIPE
RED BAT 2
BAT 2
YELLOW/RED
RAB LABEL - ADD
WHITE - RED STRIPE
BLACK
UNSWITCHED HOT
BODINE BSL722 LED EMERGENCY DRIVER
WHITE
WHITE
LEAVE OPEN DO NOT CONNECT DURING MANUFACTURING
WHITE RED
BLUE
BATTERY 1
BATTERY 2
WHITE WHITE
BROWN
BLUE
VIOLET
RED
GREY
LABEL PROVIDED CHARGING INDICATOR LIGHT / TEST SWITCH
BLACK
CHARGING INDICATOR/ TEST SWITCH
BLACK
GREY WHITE/BLACK YELLOW - BLACK STRIPE
YELLOW
WHITE
COM
CUSTOMER SHOULD CONNECT ONLY AFTER FINISHING WIRING TO AC POWER. BATTERY COULD HAVE CHARGE & SHOCK
WHITE
YELLOW/RED
WHITE
RED-WHITE STRIPE
WHITE
BLUE/ORANGE
YELLOW/RED
RAB LABEL - ADD
BAT 1
EMERGENCY HOUSING
RED BLACK
AC DRIVER WHITE
BLACK RED BLACK
RED
BLUE
RED BLACK
GROUND
FFLED18
FFLED18 (3X6) EMERGENCY COLD 120V OR 277V WIRING DIAGRAM
FFLED18 EMG-IN-0412
KS
4.18.12 LED18W EMERGY COLD 120V OR 277V WIRING
