iPod Nano 4th Generation Logic Board Assembly Replacement
iPod Nano 4th Generation Logic Board Assembly Replacement
iPod Nano 4th Generation Logic Board Assembly Replacement Written By: Walter Galan
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
INTRODUCTION Replacing the logic board assembly gives you new flash memory as well as a new battery.
TOOLS: iFixit Opening Tools (1) Phillips #00 Screwdriver (1) Spudger (1) Tweezers (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 1 — Glass Panel
Insert the edge of an iPod opening tool into the gap between the outer case and the top bezel.
Pry the top bezel off the adhesive securing it to the display retainer.
At this point the hold switch slider is free and may fall. Be careful not to lose it. Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the hold switch slider from the top of the Nano.
Page 3 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 3
Remove the two angled Phillips screws from the two corners of the display retainer.
These screw heads are extremely small and easily stripped.
Step 4
Insert an iPod opening tool between the outer case and the display retainer.
Use the tool to slide the display assembly out of the case slightly.
Do not rotate the display retainer about the top edge of the display, as it is attached to a thin steel bracket that is easily broken.
Do not forcefully remove the display retainer, as the hold switch cable is liable to snap.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 5
Slide the display out of the Nano. It will move about .5" until the display data cable limits its travel.
Do not put unnecessary tension on the very thin display data cable.
Step 6
With the display pulled out of the case as much as possible, gently press on the lower edge of the glass panel until it pops in slightly (~1 mm).
Use your thumbs on the lower edge of the glass panel to slide the glass down and into the case until the top edge pops up out of the case.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 7
Lift the glass panel out of the Nano.
Before reinstalling the glass panel, be sure to clean the face of the display and the inside of the panel as any dust or fingerprints will be annoyingly visible when the Nano is turned on.
Step 8 — Display
Use the edge of an iPod opening tool to separate the hold switch from the adhesive securing it to the top edge of the display.
The hold switch ribbon cable is extremely fragile and easily broken. Work gently.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 9
Peel back the Kapton tape covering the display data cable socket.
While holding the light colored socket down with one finger, use the tip of a spudger to flip the ZIF cable lock up toward the bottom of the Nano.
Step 10
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 11
Use an iPod opening tool to peel the display data cable off the thin metal plate attached to the display.
Be careful not to rip the display data cable.
Step 12
Pull the display out of the Nano, minding the hold switch cable that may get caught.
As you pull the display out of the
case, be careful not to break the hold switch cable.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 13 — Logic Board Assembly
Insert an iPod opening tool between the bottom bezel and the dock connector.
Separate the bottom bezel from the adhesive securing it to the Nano and set it aside.
Step 14
Remove the three Phillips screws along the bottom of the Nano.
These screw heads are extremely small and easily stripped.
The slightly longer of the three screws belongs in the middle.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 9 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 15
Use an iPod opening tool to pry the aluminum dock bezel out of the Nano.
The dock bezel is very thin cast aluminum. To avoid breaking it, do not excessively flex it during removal.
Step 16
Use the flat end of a spudger to separate the battery from the adhesive securing it to the outer case.
The lithium polymer battery used in the Nano is very flexible. Try not to deform it excessively while separating it from the outer case.
Use the flat end of a spudger to push the logic board assembly and battery slightly out of the bottom of the Nano. Stop once it pops out a little bit.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 10 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 17
Use the edge of an iPod opening tool to peel the click wheel ribbon cable and its ZIF socket off the dock connector.
Step 18
Use the edge of an iPod opening tool to flip the ZIF cable lock up toward the headphone jack.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 11 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 19
Use a pair of tweezers to slide the click wheel ribbon cable out of its socket.
Before proceeding, be sure that both the click wheel ribbon cable socket and its cable are freed from the adhesive securing them to the dock connector and logic board.
Peel back the cable on both ends!
Pull the logic board assembly out of the outer case, minding the hold switch and click wheel cables that may get caught.
Step 20
When reassembling, ensure the click wheel cable is toward the front of the Nano and not in the grooves on the side. If it is in the groove you will probably cut it while sliding the logic board into place.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-21 06:13:46 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 12 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement Written By: Walter Galan
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
INTRODUCTION Replacing the logic board assembly gives you new flash memory as well as a new battery.
TOOLS: iFixit Opening Tools (1) Phillips #00 Screwdriver (1) Spudger (1) Tweezers (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 1 — Glass Panel
Insert the edge of an iPod opening tool into the gap between the outer case and the top bezel.
Pry the top bezel off the adhesive securing it to the display retainer.
At this point the hold switch slider is free and may fall. Be careful not to lose it. Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the hold switch slider from the top of the Nano.
Page 3 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 3
Remove the two angled Phillips screws from the two corners of the display retainer.
These screw heads are extremely small and easily stripped.
Step 4
Insert an iPod opening tool between the outer case and the display retainer.
Use the tool to slide the display assembly out of the case slightly.
Do not rotate the display retainer about the top edge of the display, as it is attached to a thin steel bracket that is easily broken.
Do not forcefully remove the display retainer, as the hold switch cable is liable to snap.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 5
Slide the display out of the Nano. It will move about .5" until the display data cable limits its travel.
Do not put unnecessary tension on the very thin display data cable.
Step 6
With the display pulled out of the case as much as possible, gently press on the lower edge of the glass panel until it pops in slightly (~1 mm).
Use your thumbs on the lower edge of the glass panel to slide the glass down and into the case until the top edge pops up out of the case.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 7
Lift the glass panel out of the Nano.
Before reinstalling the glass panel, be sure to clean the face of the display and the inside of the panel as any dust or fingerprints will be annoyingly visible when the Nano is turned on.
Step 8 — Display
Use the edge of an iPod opening tool to separate the hold switch from the adhesive securing it to the top edge of the display.
The hold switch ribbon cable is extremely fragile and easily broken. Work gently.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 9
Peel back the Kapton tape covering the display data cable socket.
While holding the light colored socket down with one finger, use the tip of a spudger to flip the ZIF cable lock up toward the bottom of the Nano.
Step 10
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 11
Use an iPod opening tool to peel the display data cable off the thin metal plate attached to the display.
Be careful not to rip the display data cable.
Step 12
Pull the display out of the Nano, minding the hold switch cable that may get caught.
As you pull the display out of the
case, be careful not to break the hold switch cable.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 13 — Logic Board Assembly
Insert an iPod opening tool between the bottom bezel and the dock connector.
Separate the bottom bezel from the adhesive securing it to the Nano and set it aside.
Step 14
Remove the three Phillips screws along the bottom of the Nano.
These screw heads are extremely small and easily stripped.
The slightly longer of the three screws belongs in the middle.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 9 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 15
Use an iPod opening tool to pry the aluminum dock bezel out of the Nano.
The dock bezel is very thin cast aluminum. To avoid breaking it, do not excessively flex it during removal.
Step 16
Use the flat end of a spudger to separate the battery from the adhesive securing it to the outer case.
The lithium polymer battery used in the Nano is very flexible. Try not to deform it excessively while separating it from the outer case.
Use the flat end of a spudger to push the logic board assembly and battery slightly out of the bottom of the Nano. Stop once it pops out a little bit.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 10 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 17
Use the edge of an iPod opening tool to peel the click wheel ribbon cable and its ZIF socket off the dock connector.
Step 18
Use the edge of an iPod opening tool to flip the ZIF cable lock up toward the headphone jack.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 11 of 12
iPod Nano 4th Generation Logic Board Assembly Replacement
Step 19
Use a pair of tweezers to slide the click wheel ribbon cable out of its socket.
Before proceeding, be sure that both the click wheel ribbon cable socket and its cable are freed from the adhesive securing them to the dock connector and logic board.
Peel back the cable on both ends!
Pull the logic board assembly out of the outer case, minding the hold switch and click wheel cables that may get caught.
Step 20
When reassembling, ensure the click wheel cable is toward the front of the Nano and not in the grooves on the side. If it is in the groove you will probably cut it while sliding the logic board into place.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-21 06:13:46 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 12 of 12
