Jabra Speak 510 Outer Casing Replacement
Jabra Speak 510 Outer Casing Replacement
Jabra Speak 510 Outer Casing Replacement This is a prerequisite guide for the other replacement guides. This guide will provide you with step by step instructions for removing the rear panel and front panel of the Jabra Speak 510.
Written By: Jordan Murphy
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Jabra Speak 510 Outer Casing Replacement
INTRODUCTION In order to access the inner components of the Jabra Speak 510, you will need to remove the back plate and the front plate.
TOOLS: Metal Spudger Set (1) You will use the metal spudger and the small pointed metal spudger
T6 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Jabra Speak 510 Outer Casing Replacement
Step 1 — Outer Casing
Using a metal spudger, peel back the foam pad on the bottom of the device to reveal six screws.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the six 20 mm T6 screws from the bottom of the device.
Page 3 of 5
Jabra Speak 510 Outer Casing Replacement
Step 3
Remove the back plate and the grey foam underneath.
Step 4
Use a small, pointed metal spudger to release the plastic tabs connecting the faceplate to the bottom of the speaker.
A small cable connects the faceplate to the device. Carefully disconnect the cable before opening the device.
Slowly flip the device open like a clam shell.
There are several wires soldered to the motherboard that prevent the faceplate from detaching completely. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Jabra Speak 510 Outer Casing Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-19 10:17:45 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
Jabra Speak 510 Outer Casing Replacement This is a prerequisite guide for the other replacement guides. This guide will provide you with step by step instructions for removing the rear panel and front panel of the Jabra Speak 510.
Written By: Jordan Murphy
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Jabra Speak 510 Outer Casing Replacement
INTRODUCTION In order to access the inner components of the Jabra Speak 510, you will need to remove the back plate and the front plate.
TOOLS: Metal Spudger Set (1) You will use the metal spudger and the small pointed metal spudger
T6 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Jabra Speak 510 Outer Casing Replacement
Step 1 — Outer Casing
Using a metal spudger, peel back the foam pad on the bottom of the device to reveal six screws.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the six 20 mm T6 screws from the bottom of the device.
Page 3 of 5
Jabra Speak 510 Outer Casing Replacement
Step 3
Remove the back plate and the grey foam underneath.
Step 4
Use a small, pointed metal spudger to release the plastic tabs connecting the faceplate to the bottom of the speaker.
A small cable connects the faceplate to the device. Carefully disconnect the cable before opening the device.
Slowly flip the device open like a clam shell.
There are several wires soldered to the motherboard that prevent the faceplate from detaching completely. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Jabra Speak 510 Outer Casing Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-19 10:17:45 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
