JD Razor 2000 Wheelie Bar Replacement
JD Razor 2000 Wheelie Bar Replacement
JD Razor 2000 Wheelie Bar Replacement The wheelie bar allows riders keep stability. The wheelie bar also allows riders to perform tricks. This guide will show the replacement of the wheelie bar.
Written By: Shane
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
JD Razor 2000 Wheelie Bar Replacement
INTRODUCTION The wheelie bar may be deformed or just get in your way constantly. Learn how to remove and/or replace it with this guide. If you need more assistance, visit our troubleshooting guide here.
TOOLS: Macro Bit Set (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
JD Razor 2000 Wheelie Bar Replacement
Step 1 — Unscrewing the Axle Bolt
Facing the wheelie bar as shown, place your left thumb on the bolt located on the left side of the Back Wheel and place the Allen wrench into the screw on the right side of the Back Wheel.
Using the wrench, slowly unscrew the bolt while applying constant pressure from the left side.
Step 2 — Removing the Bolt and Bearing
Remove the bolt from the right side and the bearing from the left.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
JD Razor 2000 Wheelie Bar Replacement
Step 3 — Removing the Wheel
Turn the JD Razor 2000 on its side as shown. Slowly remove the Back Wheel by pulling it out at a perpendicular angle to the scooter base.
Pull the wheelie bar away from the deck of the scooter.
Step 4 — Pulling Out the Wheelie Bar
To reassemble your device, follow these instructions in reverse order. If you need more assistance, visit our troubleshooting guide here. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
JD Razor 2000 Wheelie Bar Replacement This document was last generated on 2017-06-22 08:14:40 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
JD Razor 2000 Wheelie Bar Replacement The wheelie bar allows riders keep stability. The wheelie bar also allows riders to perform tricks. This guide will show the replacement of the wheelie bar.
Written By: Shane
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
JD Razor 2000 Wheelie Bar Replacement
INTRODUCTION The wheelie bar may be deformed or just get in your way constantly. Learn how to remove and/or replace it with this guide. If you need more assistance, visit our troubleshooting guide here.
TOOLS: Macro Bit Set (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
JD Razor 2000 Wheelie Bar Replacement
Step 1 — Unscrewing the Axle Bolt
Facing the wheelie bar as shown, place your left thumb on the bolt located on the left side of the Back Wheel and place the Allen wrench into the screw on the right side of the Back Wheel.
Using the wrench, slowly unscrew the bolt while applying constant pressure from the left side.
Step 2 — Removing the Bolt and Bearing
Remove the bolt from the right side and the bearing from the left.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
JD Razor 2000 Wheelie Bar Replacement
Step 3 — Removing the Wheel
Turn the JD Razor 2000 on its side as shown. Slowly remove the Back Wheel by pulling it out at a perpendicular angle to the scooter base.
Pull the wheelie bar away from the deck of the scooter.
Step 4 — Pulling Out the Wheelie Bar
To reassemble your device, follow these instructions in reverse order. If you need more assistance, visit our troubleshooting guide here. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
JD Razor 2000 Wheelie Bar Replacement This document was last generated on 2017-06-22 08:14:40 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
