Kurio Xtreme Motherboard Replacement
Kurio Xtreme Motherboard Replacement
Kurio Xtreme Motherboard Replacement Replace the motherboard in your Kurio Xtreme.
Scritto Da: Mallory Myers
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 1 di 7
Kurio Xtreme Motherboard Replacement
INTRODUZIONE Follow this guide to replace the motherboard in your Kurio Xtreme. Before you begin, make sure that you have a soldering iron and know how to use it.
STRUMENTI: Phillips #000 Screwdriver (1) iFixit Opening Tools (1) Soldering Workstation (1)
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 2 di 7
Kurio Xtreme Motherboard Replacement
Passo 1 — Back Panel
Remove the rubber case by beginning to peel from one of the top corners and continue peeling until the cover is completely removed.
Passo 2
Unscrew the four 4 mm black screws using a Phillips #000 screw driver.
There are two screws on each side of the device (four total).
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 3 di 7
Kurio Xtreme Motherboard Replacement
Passo 3
Insert the plastic opening tool in between the edges of the blue front casing and black back casing.
Slide the plastic opening tool around the perimeter of the device. This may require that you repeatedly run the opening tool up and down the edges of the device.
Be sure not to break any of the plastic clamps along the edges of the device when removing the back cover.
Carefully lift the back panel off of the rest of the device.
Passo 4 — Motherboard
© iFixit — CC BY-NC-SA
it.iFixit.com
Unscrew the three 4 mm screws with a Phillips #000 screwdriver.
Pagina 4 di 7
Kurio Xtreme Motherboard Replacement
Passo 5
Remove the orange data display ribbon wire above the battery by prying open the ZIF connector with the plastic opening tool.
Passo 6
Remove the orange data display ribbon wire to the left of the battery by prying open the ZIF connector with the plastic opening tool.
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 5 di 7
Kurio Xtreme Motherboard Replacement
Passo 7
Remove the 7 wires connected to the motherboard by soldering the ends that connect them to the motherboard.
2 pairs of red and black speaker wires (4 wires total)
1 pair of red and black battery wires (2 wires total)
1 gray ground wire
The soldering iron gets very hot and may injure you if exposed to your skin. Passo 8
© iFixit — CC BY-NC-SA
it.iFixit.com
Remove the motherboard by lifting it out of the casing.
Pagina 6 di 7
Kurio Xtreme Motherboard Replacement
To reassemble your device, follow these instructions in reverse order. Questo documento è stato generato l'ultima volta su 2017-10-13 02:10:15 PM.
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 7 di 7
Kurio Xtreme Motherboard Replacement Replace the motherboard in your Kurio Xtreme.
Scritto Da: Mallory Myers
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 1 di 7
Kurio Xtreme Motherboard Replacement
INTRODUZIONE Follow this guide to replace the motherboard in your Kurio Xtreme. Before you begin, make sure that you have a soldering iron and know how to use it.
STRUMENTI: Phillips #000 Screwdriver (1) iFixit Opening Tools (1) Soldering Workstation (1)
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 2 di 7
Kurio Xtreme Motherboard Replacement
Passo 1 — Back Panel
Remove the rubber case by beginning to peel from one of the top corners and continue peeling until the cover is completely removed.
Passo 2
Unscrew the four 4 mm black screws using a Phillips #000 screw driver.
There are two screws on each side of the device (four total).
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 3 di 7
Kurio Xtreme Motherboard Replacement
Passo 3
Insert the plastic opening tool in between the edges of the blue front casing and black back casing.
Slide the plastic opening tool around the perimeter of the device. This may require that you repeatedly run the opening tool up and down the edges of the device.
Be sure not to break any of the plastic clamps along the edges of the device when removing the back cover.
Carefully lift the back panel off of the rest of the device.
Passo 4 — Motherboard
© iFixit — CC BY-NC-SA
it.iFixit.com
Unscrew the three 4 mm screws with a Phillips #000 screwdriver.
Pagina 4 di 7
Kurio Xtreme Motherboard Replacement
Passo 5
Remove the orange data display ribbon wire above the battery by prying open the ZIF connector with the plastic opening tool.
Passo 6
Remove the orange data display ribbon wire to the left of the battery by prying open the ZIF connector with the plastic opening tool.
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 5 di 7
Kurio Xtreme Motherboard Replacement
Passo 7
Remove the 7 wires connected to the motherboard by soldering the ends that connect them to the motherboard.
2 pairs of red and black speaker wires (4 wires total)
1 pair of red and black battery wires (2 wires total)
1 gray ground wire
The soldering iron gets very hot and may injure you if exposed to your skin. Passo 8
© iFixit — CC BY-NC-SA
it.iFixit.com
Remove the motherboard by lifting it out of the casing.
Pagina 6 di 7
Kurio Xtreme Motherboard Replacement
To reassemble your device, follow these instructions in reverse order. Questo documento è stato generato l'ultima volta su 2017-10-13 02:10:15 PM.
© iFixit — CC BY-NC-SA
it.iFixit.com
Pagina 7 di 7
