LA 5638 Explorer Plan - Swing N Slide
R
PB 8285
check out http://www.swing-n-slide.com/planupdates.htm for updates to these instructions.
Kit Components: PB 8263 Swing Beam PB 8270 Platform NE 4700-T Slide Assembly Instructions: PAGES 8-28
29'
NOTE: PAGES 29-49 DO NOT APPLY TO THE PB 8285 DESIGN 22' No. of Children: Up to 6 Min. Use Zone: 29' x 22' Set Dim. 12'W x 10'L x 9'H Est. Building Time: 2 hrs. (Tower only.)
ASSEMBLY INSTRUCTIONS Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232 © PlayCore Inc. 2010
Printed In USA
LA 6084
Assembly Instructions Fig. 20
NOTE: THESE SLIDE INSTRUCTIONS REPLACE THOSE ON PAGE 27 OF YOUR ASSEMBLY PLAN.
Fig. 20a
1
2 11
5 3
6
7
8
9
10
4
Fig. 20b (22) 5/16'' loc-nut
Fig. 20c (44) 5/16'' flat washers (2) 1-1/4'' screws per joint
2'' x 4'' x 12''
2'' Above Ground
Summit Slide Installation. 1. Align Summit slide sections together on the ground. Begin attaching two Summit slide sections together by securing the two outer most bolts in place finger tight (see (Fig. 20a) for proper Bolt Sequence). Following this pattern install (1) bolt, (2) washers and (1) loc-nut per hole (see (Fig. 20b)). Once all (11) bolts, (22) flat washers and (11) loc-nuts are in place go back and tighten all hardware with appropriate tools. 2. Consult (Fig. 20) For proper placement of Summit slide on your unit. 3. Drive wood stake into ground leaving 2'' exposed. 4. Secure the Summit slide bottom to the stake using (2) 1-1/4'' deck screws. (Fig. 20C). 5. Attach Summit slide to unit as shown in (Fig. 20).
© PlayCore Inc. 2010
Printed In USA
2
LA 6084
PB 8285
check out http://www.swing-n-slide.com/planupdates.htm for updates to these instructions.
Kit Components: PB 8263 Swing Beam PB 8270 Platform NE 4700-T Slide Assembly Instructions: PAGES 8-28
29'
NOTE: PAGES 29-49 DO NOT APPLY TO THE PB 8285 DESIGN 22' No. of Children: Up to 6 Min. Use Zone: 29' x 22' Set Dim. 12'W x 10'L x 9'H Est. Building Time: 2 hrs. (Tower only.)
ASSEMBLY INSTRUCTIONS Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232 © PlayCore Inc. 2010
Printed In USA
LA 6084
Assembly Instructions Fig. 20
NOTE: THESE SLIDE INSTRUCTIONS REPLACE THOSE ON PAGE 27 OF YOUR ASSEMBLY PLAN.
Fig. 20a
1
2 11
5 3
6
7
8
9
10
4
Fig. 20b (22) 5/16'' loc-nut
Fig. 20c (44) 5/16'' flat washers (2) 1-1/4'' screws per joint
2'' x 4'' x 12''
2'' Above Ground
Summit Slide Installation. 1. Align Summit slide sections together on the ground. Begin attaching two Summit slide sections together by securing the two outer most bolts in place finger tight (see (Fig. 20a) for proper Bolt Sequence). Following this pattern install (1) bolt, (2) washers and (1) loc-nut per hole (see (Fig. 20b)). Once all (11) bolts, (22) flat washers and (11) loc-nuts are in place go back and tighten all hardware with appropriate tools. 2. Consult (Fig. 20) For proper placement of Summit slide on your unit. 3. Drive wood stake into ground leaving 2'' exposed. 4. Secure the Summit slide bottom to the stake using (2) 1-1/4'' deck screws. (Fig. 20C). 5. Attach Summit slide to unit as shown in (Fig. 20).
© PlayCore Inc. 2010
Printed In USA
2
LA 6084
