MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement i will show you how to change the trackpad.
Written By: SIMRAN
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
INTRODUCTION This guide has been updated by iFixit staff! Read the new, official guide here.
TOOLS: Phillips #00 Screwdriver (1) Phillips #000 Screwdriver (1) Y1 Tri-wing Screwdriver (1) Spudger (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
Step 1 — Trackpad
Remove the following 10 screws securing the lower case to the MacBook Pro 13" Unibody:
Red Seven 3 mm Phillips screws.
Orange Three 13.5 mm Phillips screws.
Slightly lift the lower case and push it toward the rear of the computer to free the mounting tabs.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
Step 3
Remove the following tri-wing screws securing the battery to the upper case:
Red One 5.5 mm tri-wing screw
Orange One 13.5 mm tri-wing screw.
Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
Step 5
Lift the battery out of the upper case
Step 6
Remove the ribbon cable by releasing it from the ZIF connector on the underside of the trackpad and also from the socket that attaches it to the logic board.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
Step 7
Remove the four 1.2mm #00 Phillips head screws from rear of the trackpad.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-26 05:11:38 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement i will show you how to change the trackpad.
Written By: SIMRAN
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
INTRODUCTION This guide has been updated by iFixit staff! Read the new, official guide here.
TOOLS: Phillips #00 Screwdriver (1) Phillips #000 Screwdriver (1) Y1 Tri-wing Screwdriver (1) Spudger (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
Step 1 — Trackpad
Remove the following 10 screws securing the lower case to the MacBook Pro 13" Unibody:
Red Seven 3 mm Phillips screws.
Orange Three 13.5 mm Phillips screws.
Slightly lift the lower case and push it toward the rear of the computer to free the mounting tabs.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
Step 3
Remove the following tri-wing screws securing the battery to the upper case:
Red One 5.5 mm tri-wing screw
Orange One 13.5 mm tri-wing screw.
Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
Step 5
Lift the battery out of the upper case
Step 6
Remove the ribbon cable by releasing it from the ZIF connector on the underside of the trackpad and also from the socket that attaches it to the logic board.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
MacBook Pro 13" Unibody Mid 2009 Trackpad Replacement
Step 7
Remove the four 1.2mm #00 Phillips head screws from rear of the trackpad.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-26 05:11:38 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
