Magpul installation Square Bottom and 10/20 Mags Angled Bottom 10 ...
Square Bottom and 10/20 Mags THE ULTIMATE BULLET BUTTON TOOL
KIT A “PATENT PENDING”
PACK KIT A OF FOUR (Metal)
All UBBT products are 100% guaranteed to be free of material and workmanship defects and can be returned no questions asked. (We recommend contacting us for technical assistance before returning items).
1.
2.
3. 4.
Remove magazine bottom cover with a flat screwdriver and take out the guts. (Beware of the spring) Drill 1/8” hole on FRONT face of magazine about 3/16” from bottom edge and centered in the width. (Fig 1) Insert screw through inside and screw on plastic tip. Tighten with screwdriver. Replace guts and bottom cover.
Email us at: [email protected] Buyer is responsible for shipping costs on returns. Any defective items that are NOT manufactured by Thordsen Customs will be replaced or refunded at our discretion. Thordsen Customs assumes that our products will be used in a manner consistent with California state law and WILL NOT be held liable for ANY misuse of our products.
Angled Bottom 10 Round Mags
Magpul installation 1. 2. 3.
Drill or poke a 1/16 diameter hole through either edge of the magpul. Insert screw and washer from the inside and screw the tip on until tight. Slip magpul onto magazine with tip facing the front.
1.
2.
3. 4.
5. Copyright 2011 Thordsen Customs LLC
Remove magazine bottom cover with a flat screwdriver and take out the guts. (Beware of the spring) Drill 1/8” hole on FRONT face of magazine about 3/16” from bottom edge and centered in the width. (Fig 1) Insert screw through inside and screw on the plastic tip. Using a saw, Dremel, or utility knife, cut a notch in the follower for the screw head to clear. (Fig 2) This will insure that the mag can hold 10 rounds. Replace guts and bottom. Copyright 2011 Thordsen Customs LLC
KIT A “PATENT PENDING”
PACK KIT A OF FOUR (Metal)
All UBBT products are 100% guaranteed to be free of material and workmanship defects and can be returned no questions asked. (We recommend contacting us for technical assistance before returning items).
1.
2.
3. 4.
Remove magazine bottom cover with a flat screwdriver and take out the guts. (Beware of the spring) Drill 1/8” hole on FRONT face of magazine about 3/16” from bottom edge and centered in the width. (Fig 1) Insert screw through inside and screw on plastic tip. Tighten with screwdriver. Replace guts and bottom cover.
Email us at: [email protected] Buyer is responsible for shipping costs on returns. Any defective items that are NOT manufactured by Thordsen Customs will be replaced or refunded at our discretion. Thordsen Customs assumes that our products will be used in a manner consistent with California state law and WILL NOT be held liable for ANY misuse of our products.
Angled Bottom 10 Round Mags
Magpul installation 1. 2. 3.
Drill or poke a 1/16 diameter hole through either edge of the magpul. Insert screw and washer from the inside and screw the tip on until tight. Slip magpul onto magazine with tip facing the front.
1.
2.
3. 4.
5. Copyright 2011 Thordsen Customs LLC
Remove magazine bottom cover with a flat screwdriver and take out the guts. (Beware of the spring) Drill 1/8” hole on FRONT face of magazine about 3/16” from bottom edge and centered in the width. (Fig 1) Insert screw through inside and screw on the plastic tip. Using a saw, Dremel, or utility knife, cut a notch in the follower for the screw head to clear. (Fig 2) This will insure that the mag can hold 10 rounds. Replace guts and bottom. Copyright 2011 Thordsen Customs LLC
