MMZ2012Type - TDK Product Center
E M C
C o m p o n e n t s July 2016
Chip beads For general signal line
MMZ series
MMZ2012 MMZ2012
2012[0805 inch]* * Dimensions code JIS[EIA]
Type
(2/11)
E M C
C o m p o n e n t s
Reminders for using these products Before using these products, be sure to request the delivery specifications.
Safety reminders Please pay sufficient attention to the warnings for safe designing when using this products.
Reminders The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment
(8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.
20160722 / beads_commercial_signal_mmz2012_en.fm
(3/11)
E M C
C o m p o n e n t s Product compatible with RoHS directive Halogen-free Compatible with lead-free solders
Chip beads For general signal line
Overview of MMZ2012 type FEATURES Noise reduction solution for general signal line. Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to high-speed signals.
APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment.
PART NUMBER CONSTRUCTION
MMZ Series name
2012
R
L×W×T dimensions (mm) 2012 2.0×1.25x0.85
Material name D R S Y
150
A
Impedance () at 100MHz 121 120 150 15
Characteristic type A B
T
000
Packaging style
Internal code
T
Taping
000
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature ranges Operating Storage Type temperature temperature （°C） （°C） MMZ2012 –55 to +125 –55 to +125 The storage temperature range is for after the circuit board is mounted.
Package quantity
Individual weight
(pieces/reel) 4,000
（mg） 8
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(4/11)
E M C
C o m p o n e n t s
MMZ2012 type RECOMMENDED REFLOW PROFILE Preheating
Soldering
Natural cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1 t1
t2
t: Time
Preheating Temp. T1 T2 150°C 180°C
Time t1 60 to 120s
Soldering Temp. Time T3 t2 230°C 30 to 60s
Peak Temp. T4 250 to 260°C
Time t3 10s
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(5/11)
E M C
C o m p o n e n t s
MMZ2012 type MATERIAL CHARACTERISTIC R material: for wide frequency applications calling for broad impedance characteristics. For digital signal line applications calling requiring good waveform integrity. Impedance values selected for effectiveness at 10 to 200MHz. S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. Y material: High frequency range type intended for the 100MHz region and above. For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for effectiveness at 80 to 400MHz. D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 2500
Impedance(Ω)
2000 Y
1500 1000 500 0 10
S
D
R
100 Frequency(MHz)
1000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(6/11)
E M C
C o m p o n e n t s
MMZ2012 type SHAPE & DIMENSIONS
0.85±0.2
1.25±0.2
2±0.2
Dimensions in mm
0.5±0.3
1.2
RECOMMENDED LAND PATTERN
0.8
1
0.8
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(7/11)
E M C
C o m p o n e n t s
MMZ2012 type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] ( ) 15 30 60 120 300 600 1000 40 80 120 180 300 600 1000 15 30 60 120 300 600 1000 1500 2000 80 120 300
Tolerance ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25%
DC resistance
Rated current
Part No.
( )max. 0.05 0.05 0.10 0.12 0.15 0.20 0.30 0.10 0.10 0.15 0.15 0.20 0.30 0.35 0.05 0.05 0.10 0.12 0.15 0.20 0.30 0.40 0.50 0.30 0.30 0.50
(mA)max. 1500 1500 1000 800 600 500 500 1000 800 800 600 600 500 500 1500 1500 1000 800 600 500 500 500 400 500 500 400
MMZ2012R150AT000 MMZ2012R300AT000 MMZ2012R600AT000 MMZ2012R121AT000 MMZ2012R301AT000 MMZ2012R601AT000 MMZ2012R102AT000 MMZ2012S400AT000 MMZ2012S800AT000 MMZ2012S121AT000 MMZ2012S181AT000 MMZ2012S301AT000 MMZ2012S601AT000 MMZ2012S102AT000 MMZ2012Y150BT000 MMZ2012Y300BT000 MMZ2012Y600BT000 MMZ2012Y121BT000 MMZ2012Y301BT000 MMZ2012Y601BT000 MMZ2012Y102BT000 MMZ2012Y152BT000 MMZ2012Y202BT000 MMZ2012D800BT000 MMZ2012D121BT000 MMZ2012D301BT000
○ Measurement equipment Measurement item Product No. Impedance E4991A+16192A DC resistance Type-7556 ＊ Equivalent measurement equipment may be used.
Manufacturer Keysight Technologies Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(8/11)
E M C
C o m p o n e n t s
MMZ2012 type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ2012R series MMZ2012S series MMZ2012R102A MMZ2012R601A
1000
MMZ2012R301A
MMZ2012R121A
900
MMZ2012R600A
800
MMZ2012R300A MMZ2012R150A
700 600 500 400
MMZ2012S181A
500 400 200
100
100 10000
2000
600
300
100 1000 Frequency (MHz)
MMZ2012S601A MMZ2012S301A
700
200
10
MMZ2012Y202B
MMZ2012S121A
800
300
0 1
2500 MMZ2012S102A
1000 MMZ2012S800A 900 MMZ2012S400A Impedance (Ω)
1100
1100
Impedance (Ω)
1200
Impedance (Ω)
MMZ2012Y series
1200
0 1
MMZ2012Y600B
MMZ2012Y152B
MMZ2012Y300B
MMZ2012Y102B
1500 MMZ2012Y150B
MMZ2012Y601B MMZ2012Y301B MMZ2012Y121B
1000
500
10
100 1000 Frequency (MHz)
10000
0 1
10
100 1000 Frequency (MHz)
10000
MMZ2012D series 4500 4000 MMZ2012D301B
Impedance (Ω)
3500 3000 2500 2000
MMZ2012D121B
1500 MMZ2012D800B 1000 500 0 1
10
100 1000 Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(9/11)
E M C
C o m p o n e n t s
MMZ2012 type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ2012R150AT000 MMZ2012R300AT000
R X
10
100 1000 Frequency (MHz)
10000
140 120 100 80 60 40 20 0 1
Z
R X
10
100 1000 Frequency (MHz)
10000
350 300 250 200 150 100 50 0 1
60
1000
50
Z
600
R
400 200 0 1
X
10
100 1000 Frequency (MHz)
700 600 500 400 300 200 100 0 1
X
100 1000 Frequency (MHz)
10000
Z
30
R
20
X
10 10
Z R
100 1000 Frequency (MHz)
10000
X
10
100 1000 Frequency (MHz)
Z
R
50 0 1
10000
140 120 100 80 60 40 20 0 1
X
10
100 1000 Frequency (MHz)
10000
Impedance (Ω)
MMZ2012S102AT000
Z R X
10
200 100
100 1000 Frequency (MHz)
10000
450 400 350 300 250 200 150 100 50 0 1
30
1000
25
600
Z
R
400 200 0 1
X
10
10
100 1000 Frequency (MHz)
10000
Z R X
10
100 1000 Frequency (MHz)
10000
Z R X
10
100 1000 Frequency (MHz)
10000
Z
R X
10
100 1000 Frequency (MHz)
10000
MMZ2012Y150BT000
1200 800
X
MMZ2012S301AT000
250 150
R
MMZ2012S800AT000
300 Impedance (Ω)
Impedance (Ω) Impedance (Ω)
R
10
Z
MMZ2012R601AT000
MMZ2012S181AT000
MMZ2012S601AT000 700 600 500 400 300 200 100 0 1
10000
Z
40
0 1
10000
MMZ2012S121AT000 180 160 140 120 100 80 60 40 20 0 1
100 1000 Frequency (MHz)
MMZ2012S400AT000
1200 Impedance (Ω)
Impedance (Ω)
MMZ2012R102AT000
800
10
MMZ2012R301AT000
Impedance (Ω)
Impedance (Ω)
MMZ2012R121AT000
X
Impedance (Ω)
0 1
R
Impedance (Ω)
5
Z
Impedance (Ω)
Z
10
90 80 70 60 50 40 30 20 10 0 1
Impedance (Ω)
15
Impedance (Ω)
Impedance (Ω)
20
Impedance (Ω)
40 0 35 30 25 20 15 10 5 0 1
25
MMZ2012R600AT000
100 1000 Frequency (MHz)
10000
Z
20
R
15 10
X
5 0 1
10
100 1000 Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(10/11)
E M C
C o m p o n e n t s
MMZ2012 type ELECTRICAL CHARACTERISTICS
120
40
100
Z
30
R
20 10
X
100 1000 Frequency (MHz)
Impedance (Ω)
Impedance (Ω)
Z
R
300 200 100 0 1
X
10
100 1000 Frequency (MHz)
10000
Z R
X
10
100 1000 Frequency (MHz)
10
100 1000 Frequency (MHz)
800 700 600 500 400 300 200 100 0
Z R
100 50 0 1
10000
X
10
100 1000 Frequency (MHz)
10000
MMZ2012Y102BT000 1200 1000
Z
R
X
1
10
100 1000 Frequency (MHz)
R
400 X
200 10
100 1000 Frequency (MHz)
10000
MMZ2012D800BT000
Z
1500 1000 X R
10
Z
600
0 1
10000
2000
500
800
100 1000 Frequency (MHz)
10000
700 600 500 400 300 200 100 0 1
Z
10
X R 100 1000 Frequency (MHz)
10000
MMZ2012D301BT000
Impedance (Ω)
1000
Impedance (Ω)
1
0 1
10000
1200 800 600 400 0 1
X
20
150
2500
MMZ2012D121BT000
200
40
MMZ2012Y202BT000
Impedance (Ω)
Impedance (Ω)
MMZ2012Y152BT000 1800 1600 1400 1200 1000 800 600 400 200 0 1
R
MMZ2012Y601BT000
600 500 400
Z
60
0
10000
MMZ2012Y301BT000
80
Impedance (Ω)
10
200
Impedance (Ω)
0 1
MMZ2012Y121BT000
Impedance (Ω)
50
Impedance (Ω)
Impedance (Ω)
Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ2012Y300BT000 MMZ2012Y600BT000
Z X R 10 100 1000 Frequency (MHz)
10000
4500 4000 3500 3000 2500 2000 1500 1000 500 0 1
Z R
10
X
100 1000 Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(11/11)
E M C
C o m p o n e n t s
MMZ2012 type PACKAGING STYLE REEL DIMENSIONS
ø60min.
2.0±0.5
1.0 8.4 +2.0 –0.0
ø13±0.2 ø21±0.8
14.4max.
ø180±2.0 Dimensions in mm
4.0±0.1
B
8.0±0.3
2.0±0.05
3.5±0.05
1.5 +0.1 0
1.75±0.1
TAPE DIMENSIONS
K
4.0±0.1
A
Dimensions in mm
Type MMZ2012
160min.
Drawing direction
A 1.5±0.2
Taping
B 2.3±0.2
P1 4.0±0.1
K 1.1max.
200min.
300min.
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
C o m p o n e n t s July 2016
Chip beads For general signal line
MMZ series
MMZ2012 MMZ2012
2012[0805 inch]* * Dimensions code JIS[EIA]
Type
(2/11)
E M C
C o m p o n e n t s
Reminders for using these products Before using these products, be sure to request the delivery specifications.
Safety reminders Please pay sufficient attention to the warnings for safe designing when using this products.
Reminders The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment
(8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.
20160722 / beads_commercial_signal_mmz2012_en.fm
(3/11)
E M C
C o m p o n e n t s Product compatible with RoHS directive Halogen-free Compatible with lead-free solders
Chip beads For general signal line
Overview of MMZ2012 type FEATURES Noise reduction solution for general signal line. Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to high-speed signals.
APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment.
PART NUMBER CONSTRUCTION
MMZ Series name
2012
R
L×W×T dimensions (mm) 2012 2.0×1.25x0.85
Material name D R S Y
150
A
Impedance () at 100MHz 121 120 150 15
Characteristic type A B
T
000
Packaging style
Internal code
T
Taping
000
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature ranges Operating Storage Type temperature temperature （°C） （°C） MMZ2012 –55 to +125 –55 to +125 The storage temperature range is for after the circuit board is mounted.
Package quantity
Individual weight
(pieces/reel) 4,000
（mg） 8
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(4/11)
E M C
C o m p o n e n t s
MMZ2012 type RECOMMENDED REFLOW PROFILE Preheating
Soldering
Natural cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1 t1
t2
t: Time
Preheating Temp. T1 T2 150°C 180°C
Time t1 60 to 120s
Soldering Temp. Time T3 t2 230°C 30 to 60s
Peak Temp. T4 250 to 260°C
Time t3 10s
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(5/11)
E M C
C o m p o n e n t s
MMZ2012 type MATERIAL CHARACTERISTIC R material: for wide frequency applications calling for broad impedance characteristics. For digital signal line applications calling requiring good waveform integrity. Impedance values selected for effectiveness at 10 to 200MHz. S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. Y material: High frequency range type intended for the 100MHz region and above. For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for effectiveness at 80 to 400MHz. D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 2500
Impedance(Ω)
2000 Y
1500 1000 500 0 10
S
D
R
100 Frequency(MHz)
1000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(6/11)
E M C
C o m p o n e n t s
MMZ2012 type SHAPE & DIMENSIONS
0.85±0.2
1.25±0.2
2±0.2
Dimensions in mm
0.5±0.3
1.2
RECOMMENDED LAND PATTERN
0.8
1
0.8
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(7/11)
E M C
C o m p o n e n t s
MMZ2012 type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] ( ) 15 30 60 120 300 600 1000 40 80 120 180 300 600 1000 15 30 60 120 300 600 1000 1500 2000 80 120 300
Tolerance ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25%
DC resistance
Rated current
Part No.
( )max. 0.05 0.05 0.10 0.12 0.15 0.20 0.30 0.10 0.10 0.15 0.15 0.20 0.30 0.35 0.05 0.05 0.10 0.12 0.15 0.20 0.30 0.40 0.50 0.30 0.30 0.50
(mA)max. 1500 1500 1000 800 600 500 500 1000 800 800 600 600 500 500 1500 1500 1000 800 600 500 500 500 400 500 500 400
MMZ2012R150AT000 MMZ2012R300AT000 MMZ2012R600AT000 MMZ2012R121AT000 MMZ2012R301AT000 MMZ2012R601AT000 MMZ2012R102AT000 MMZ2012S400AT000 MMZ2012S800AT000 MMZ2012S121AT000 MMZ2012S181AT000 MMZ2012S301AT000 MMZ2012S601AT000 MMZ2012S102AT000 MMZ2012Y150BT000 MMZ2012Y300BT000 MMZ2012Y600BT000 MMZ2012Y121BT000 MMZ2012Y301BT000 MMZ2012Y601BT000 MMZ2012Y102BT000 MMZ2012Y152BT000 MMZ2012Y202BT000 MMZ2012D800BT000 MMZ2012D121BT000 MMZ2012D301BT000
○ Measurement equipment Measurement item Product No. Impedance E4991A+16192A DC resistance Type-7556 ＊ Equivalent measurement equipment may be used.
Manufacturer Keysight Technologies Yokogawa
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(8/11)
E M C
C o m p o n e n t s
MMZ2012 type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ2012R series MMZ2012S series MMZ2012R102A MMZ2012R601A
1000
MMZ2012R301A
MMZ2012R121A
900
MMZ2012R600A
800
MMZ2012R300A MMZ2012R150A
700 600 500 400
MMZ2012S181A
500 400 200
100
100 10000
2000
600
300
100 1000 Frequency (MHz)
MMZ2012S601A MMZ2012S301A
700
200
10
MMZ2012Y202B
MMZ2012S121A
800
300
0 1
2500 MMZ2012S102A
1000 MMZ2012S800A 900 MMZ2012S400A Impedance (Ω)
1100
1100
Impedance (Ω)
1200
Impedance (Ω)
MMZ2012Y series
1200
0 1
MMZ2012Y600B
MMZ2012Y152B
MMZ2012Y300B
MMZ2012Y102B
1500 MMZ2012Y150B
MMZ2012Y601B MMZ2012Y301B MMZ2012Y121B
1000
500
10
100 1000 Frequency (MHz)
10000
0 1
10
100 1000 Frequency (MHz)
10000
MMZ2012D series 4500 4000 MMZ2012D301B
Impedance (Ω)
3500 3000 2500 2000
MMZ2012D121B
1500 MMZ2012D800B 1000 500 0 1
10
100 1000 Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(9/11)
E M C
C o m p o n e n t s
MMZ2012 type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ2012R150AT000 MMZ2012R300AT000
R X
10
100 1000 Frequency (MHz)
10000
140 120 100 80 60 40 20 0 1
Z
R X
10
100 1000 Frequency (MHz)
10000
350 300 250 200 150 100 50 0 1
60
1000
50
Z
600
R
400 200 0 1
X
10
100 1000 Frequency (MHz)
700 600 500 400 300 200 100 0 1
X
100 1000 Frequency (MHz)
10000
Z
30
R
20
X
10 10
Z R
100 1000 Frequency (MHz)
10000
X
10
100 1000 Frequency (MHz)
Z
R
50 0 1
10000
140 120 100 80 60 40 20 0 1
X
10
100 1000 Frequency (MHz)
10000
Impedance (Ω)
MMZ2012S102AT000
Z R X
10
200 100
100 1000 Frequency (MHz)
10000
450 400 350 300 250 200 150 100 50 0 1
30
1000
25
600
Z
R
400 200 0 1
X
10
10
100 1000 Frequency (MHz)
10000
Z R X
10
100 1000 Frequency (MHz)
10000
Z R X
10
100 1000 Frequency (MHz)
10000
Z
R X
10
100 1000 Frequency (MHz)
10000
MMZ2012Y150BT000
1200 800
X
MMZ2012S301AT000
250 150
R
MMZ2012S800AT000
300 Impedance (Ω)
Impedance (Ω) Impedance (Ω)
R
10
Z
MMZ2012R601AT000
MMZ2012S181AT000
MMZ2012S601AT000 700 600 500 400 300 200 100 0 1
10000
Z
40
0 1
10000
MMZ2012S121AT000 180 160 140 120 100 80 60 40 20 0 1
100 1000 Frequency (MHz)
MMZ2012S400AT000
1200 Impedance (Ω)
Impedance (Ω)
MMZ2012R102AT000
800
10
MMZ2012R301AT000
Impedance (Ω)
Impedance (Ω)
MMZ2012R121AT000
X
Impedance (Ω)
0 1
R
Impedance (Ω)
5
Z
Impedance (Ω)
Z
10
90 80 70 60 50 40 30 20 10 0 1
Impedance (Ω)
15
Impedance (Ω)
Impedance (Ω)
20
Impedance (Ω)
40 0 35 30 25 20 15 10 5 0 1
25
MMZ2012R600AT000
100 1000 Frequency (MHz)
10000
Z
20
R
15 10
X
5 0 1
10
100 1000 Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(10/11)
E M C
C o m p o n e n t s
MMZ2012 type ELECTRICAL CHARACTERISTICS
120
40
100
Z
30
R
20 10
X
100 1000 Frequency (MHz)
Impedance (Ω)
Impedance (Ω)
Z
R
300 200 100 0 1
X
10
100 1000 Frequency (MHz)
10000
Z R
X
10
100 1000 Frequency (MHz)
10
100 1000 Frequency (MHz)
800 700 600 500 400 300 200 100 0
Z R
100 50 0 1
10000
X
10
100 1000 Frequency (MHz)
10000
MMZ2012Y102BT000 1200 1000
Z
R
X
1
10
100 1000 Frequency (MHz)
R
400 X
200 10
100 1000 Frequency (MHz)
10000
MMZ2012D800BT000
Z
1500 1000 X R
10
Z
600
0 1
10000
2000
500
800
100 1000 Frequency (MHz)
10000
700 600 500 400 300 200 100 0 1
Z
10
X R 100 1000 Frequency (MHz)
10000
MMZ2012D301BT000
Impedance (Ω)
1000
Impedance (Ω)
1
0 1
10000
1200 800 600 400 0 1
X
20
150
2500
MMZ2012D121BT000
200
40
MMZ2012Y202BT000
Impedance (Ω)
Impedance (Ω)
MMZ2012Y152BT000 1800 1600 1400 1200 1000 800 600 400 200 0 1
R
MMZ2012Y601BT000
600 500 400
Z
60
0
10000
MMZ2012Y301BT000
80
Impedance (Ω)
10
200
Impedance (Ω)
0 1
MMZ2012Y121BT000
Impedance (Ω)
50
Impedance (Ω)
Impedance (Ω)
Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ2012Y300BT000 MMZ2012Y600BT000
Z X R 10 100 1000 Frequency (MHz)
10000
4500 4000 3500 3000 2500 2000 1500 1000 500 0 1
Z R
10
X
100 1000 Frequency (MHz)
10000
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
(11/11)
E M C
C o m p o n e n t s
MMZ2012 type PACKAGING STYLE REEL DIMENSIONS
ø60min.
2.0±0.5
1.0 8.4 +2.0 –0.0
ø13±0.2 ø21±0.8
14.4max.
ø180±2.0 Dimensions in mm
4.0±0.1
B
8.0±0.3
2.0±0.05
3.5±0.05
1.5 +0.1 0
1.75±0.1
TAPE DIMENSIONS
K
4.0±0.1
A
Dimensions in mm
Type MMZ2012
160min.
Drawing direction
A 1.5±0.2
Taping
B 2.3±0.2
P1 4.0±0.1
K 1.1max.
200min.
300min.
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160722 / beads_commercial_signal_mmz2012_en.fm
