Nerf N-Strike Firestrike O-Ring and Plunger Replacement
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
Nerf N-Strike Firestrike O-Ring and Plunger Replacement Replaces the O-Ring and Plunger from the Nerf N-Strike Firestrike.
Written By: Clovis Jahan
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
INTRODUCTION If the blaster doesn't cock properly, the plunger and O-ring assembly may be damaged or broken. In this guide, you will learn how to replace the O-Ring and Plunger from the Nerf N-Strike Firestrike. This requires nothing more than a number 1 Philips screwdriver.
TOOLS: Phillips #1 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
Step 1 — Battery
Remove the 10mm chrome Phillips screw that is holding the battery plate using a #1 Phillips Screwdriver, and remove the battery cover using your hands.
Step 2
Slide out the two AAA batteries using your fingers.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
Step 3 — Blaster Casing
Remove the seven 10mm black phillips screws from the blaster casing with a #1 Phillips Screwdriver.
Step 4
Slowly pull apart the blaster casing, starting at the battery location.
Keep pulling apart slowly until it separates completely. Be cautious as to not send the internal components flying.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
Step 5
For reassembly, ensure that the chrome nut gets put back in the proper location, signified by the red box.
For reassembly, ensure that all the parts are lined up correctly on the dowels, signified by the four orange boxes.
For reassembly, note the location of the springs as highlighted in the second photo. Step 6 — O-Ring and Plunger
Without removing the barrel assembly, tilt it slightly upwards.
Slide the plunger out from the air chamber.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-20 11:38:31 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement Replaces the O-Ring and Plunger from the Nerf N-Strike Firestrike.
Written By: Clovis Jahan
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
INTRODUCTION If the blaster doesn't cock properly, the plunger and O-ring assembly may be damaged or broken. In this guide, you will learn how to replace the O-Ring and Plunger from the Nerf N-Strike Firestrike. This requires nothing more than a number 1 Philips screwdriver.
TOOLS: Phillips #1 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
Step 1 — Battery
Remove the 10mm chrome Phillips screw that is holding the battery plate using a #1 Phillips Screwdriver, and remove the battery cover using your hands.
Step 2
Slide out the two AAA batteries using your fingers.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
Step 3 — Blaster Casing
Remove the seven 10mm black phillips screws from the blaster casing with a #1 Phillips Screwdriver.
Step 4
Slowly pull apart the blaster casing, starting at the battery location.
Keep pulling apart slowly until it separates completely. Be cautious as to not send the internal components flying.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
Step 5
For reassembly, ensure that the chrome nut gets put back in the proper location, signified by the red box.
For reassembly, ensure that all the parts are lined up correctly on the dowels, signified by the four orange boxes.
For reassembly, note the location of the springs as highlighted in the second photo. Step 6 — O-Ring and Plunger
Without removing the barrel assembly, tilt it slightly upwards.
Slide the plunger out from the air chamber.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
Nerf N-Strike Firestrike O-Ring and Plunger Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-20 11:38:31 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
