NETGEAR WGT624 v3 Motherboard Replacement
NETGEAR WGT624 v3 Motherboard Replacement
NETGEAR WGT624 v3 Motherboard Replacement Follow this guide to remove the motherboard from the casing of the device.
Written By: Corey Worthington
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
NETGEAR WGT624 v3 Motherboard Replacement
INTRODUCTION Removing the motherboard will allow you to replace it, or give you access to the other components that are attached to it.
TOOLS: iFixit Opening Tools (1) T8 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
NETGEAR WGT624 v3 Motherboard Replacement
Step 1 — Lower Case
Turn the device so that the bottom is facing up.
Step 2
Use the plastic opening tool to carefully lift the rubber stops in each corner.
Do not completely remove the rubber stops, because they are difficult to replace.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
NETGEAR WGT624 v3 Motherboard Replacement
Step 3
Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.
Step 4
Lift the lower case straight up from the rest of the router.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
NETGEAR WGT624 v3 Motherboard Replacement
Step 5 — Motherboard
Remove the clear plastic casing by lifting it straight up from the router.
Step 6
Separate the motherboard from the top shell by lifting it straight up from the router.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 02:35:44 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
NETGEAR WGT624 v3 Motherboard Replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
NETGEAR WGT624 v3 Motherboard Replacement Follow this guide to remove the motherboard from the casing of the device.
Written By: Corey Worthington
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
NETGEAR WGT624 v3 Motherboard Replacement
INTRODUCTION Removing the motherboard will allow you to replace it, or give you access to the other components that are attached to it.
TOOLS: iFixit Opening Tools (1) T8 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
NETGEAR WGT624 v3 Motherboard Replacement
Step 1 — Lower Case
Turn the device so that the bottom is facing up.
Step 2
Use the plastic opening tool to carefully lift the rubber stops in each corner.
Do not completely remove the rubber stops, because they are difficult to replace.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
NETGEAR WGT624 v3 Motherboard Replacement
Step 3
Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.
Step 4
Lift the lower case straight up from the rest of the router.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
NETGEAR WGT624 v3 Motherboard Replacement
Step 5 — Motherboard
Remove the clear plastic casing by lifting it straight up from the router.
Step 6
Separate the motherboard from the top shell by lifting it straight up from the router.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 02:35:44 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
NETGEAR WGT624 v3 Motherboard Replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
