panel jack slide lock pull back slide lock to stop. then insert ... - Ortronics
R
125 EUGENE O'NEILL DRIVE NEW LONDON, CT 06320 TEL: 860-445-3800 FAX: 860-405-2990 WWW.ORTRONICS.COM
TITLE:
HDJ PANEL INSTALLATION INSTRUCTIONS
HIGH DENSITYJACK INSTALLATION JACK
SLIDE LOCK
PULL BACK SLIDE LOCK TO STOP. THEN INSERT JACK INTO PANEL (JACK WILL GO IN ONE WAY ONLY WITH SLIDE LOCK UP). PANEL
ONCE JACK SHOULDERS COME INTO CONTACT WITH BACKSIDE OF PANEL, PRESS DOWNWARD.
PUSH ON SLIDE LOCK UNTIL THE FRONT IS FLUSH WITH THE JACK FACE.
LABEL BEZEL INSTALLATION JACK ICON POCKET JACK ICON POCKET
PUSH ON LABEL BEZEL SO THAT THE TWO BOSSES ON THE BACK LINE UP WITH TWO JACK ICON POCKETS, THEN PRESS INTO PLACE.
LABEL BEZEL
INSTRUCTION SHEET #:
71601790
REV:
01
ECN #:
04319
SHEET:
1 OF 2
DWN BY:
RWS
DATE:
11/17/11
GL
11/21/12
A.M.
11/21/12
R
125 EUGENE O'NEILL DRIVE NEW LONDON, CT 06320 TEL: 860-445-3800 FAX: 860-405-2990 WWW.ORTRONICS.COM
TITLE:
HDJ PANEL INSTALLATION INSTRUCTIONS
PANEL MOUNTING INSTALLATION
SIMULATED RACK SECTION
WITH NUTS PROVIDED ATTACH WIRE MANAGEMENT BAR TO PANEL BRACKETS. TIGHTEN NUTS.
PANEL SCREWS
WIRE MANAGEMENT BAR
NUT PANEL BRACKET ATTACH PANEL TO RACK WITH SUPPLIED SCREWS. PANEL SCREWS
CABLE MANAGEMENT INSTRUCTIONS (TOP VIEW) HOOK LOOP TIES
WIRE MANAGEMENT BAR
BEND RADIUS*
* THE MINIMUM CABLE BEND RADIUS IS 4 TIMES THE OUTSIDE CABLE DIAMETER. HOOK LOOP TIE WRAPS SHOULD BE USED TO ATTACH THE CABLES TO THE WIRE MANAGEMENT BAR. THE CABLE AT THE EDGE OF THE PATCH PANEL SHOULD BE ATTACHED TO THE CABLE WHICH HAS ALREADY BEEN TIE WRAPPED TO THE WIRE MANAGEMENT BAR.
INSTRUCTION SHEET #:
71601790
REV:
01
ECN #:
04319
SHEET:
PG 2 OF 2
125 EUGENE O'NEILL DRIVE NEW LONDON, CT 06320 TEL: 860-445-3800 FAX: 860-405-2990 WWW.ORTRONICS.COM
TITLE:
HDJ PANEL INSTALLATION INSTRUCTIONS
HIGH DENSITYJACK INSTALLATION JACK
SLIDE LOCK
PULL BACK SLIDE LOCK TO STOP. THEN INSERT JACK INTO PANEL (JACK WILL GO IN ONE WAY ONLY WITH SLIDE LOCK UP). PANEL
ONCE JACK SHOULDERS COME INTO CONTACT WITH BACKSIDE OF PANEL, PRESS DOWNWARD.
PUSH ON SLIDE LOCK UNTIL THE FRONT IS FLUSH WITH THE JACK FACE.
LABEL BEZEL INSTALLATION JACK ICON POCKET JACK ICON POCKET
PUSH ON LABEL BEZEL SO THAT THE TWO BOSSES ON THE BACK LINE UP WITH TWO JACK ICON POCKETS, THEN PRESS INTO PLACE.
LABEL BEZEL
INSTRUCTION SHEET #:
71601790
REV:
01
ECN #:
04319
SHEET:
1 OF 2
DWN BY:
RWS
DATE:
11/17/11
GL
11/21/12
A.M.
11/21/12
R
125 EUGENE O'NEILL DRIVE NEW LONDON, CT 06320 TEL: 860-445-3800 FAX: 860-405-2990 WWW.ORTRONICS.COM
TITLE:
HDJ PANEL INSTALLATION INSTRUCTIONS
PANEL MOUNTING INSTALLATION
SIMULATED RACK SECTION
WITH NUTS PROVIDED ATTACH WIRE MANAGEMENT BAR TO PANEL BRACKETS. TIGHTEN NUTS.
PANEL SCREWS
WIRE MANAGEMENT BAR
NUT PANEL BRACKET ATTACH PANEL TO RACK WITH SUPPLIED SCREWS. PANEL SCREWS
CABLE MANAGEMENT INSTRUCTIONS (TOP VIEW) HOOK LOOP TIES
WIRE MANAGEMENT BAR
BEND RADIUS*
* THE MINIMUM CABLE BEND RADIUS IS 4 TIMES THE OUTSIDE CABLE DIAMETER. HOOK LOOP TIE WRAPS SHOULD BE USED TO ATTACH THE CABLES TO THE WIRE MANAGEMENT BAR. THE CABLE AT THE EDGE OF THE PATCH PANEL SHOULD BE ATTACHED TO THE CABLE WHICH HAS ALREADY BEEN TIE WRAPPED TO THE WIRE MANAGEMENT BAR.
INSTRUCTION SHEET #:
71601790
REV:
01
ECN #:
04319
SHEET:
PG 2 OF 2
