PIPE COUPLINGS

Report 2 Downloads 221 Views

PROJECT INFORMATION. APPROVAL STAMP. Project: q Approved. Address: q Approved as noted. Contractor: q Not approved. Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PIPE COUPLINGS. Steel Pipe Couplings q FIGURE 349. Water Well Reamed &. Drifted Couplings. Size. Outside Diameter. (Coupling).

PIPE COUPLINGS Steel Pipe Couplings 349 q FIGURE Water Well Reamed &

Outside Diameter (Coupling)

Size

Drifted Couplings

NPS

DN

11⁄4 11⁄2 2 21⁄2 3 31⁄2 4 5 6 8 10 12

32 40 50 65 80 90 100 125 150 200 250 300

in

1.900 2.200 2.750 3.250 4.000 4.625 5.200 6.296 7.390 9.625 11.750 14.000

mm

48 56 70 83 102 117 132 160 188 244 298 356

Length in

Unit Weight mm

23⁄4 23⁄4 33⁄8 315⁄16 41⁄16 43⁄16 45⁄16 41⁄2 411⁄16 51⁄16 59⁄16 515⁄16

70 70 86 100 103 106 110 114 119 129 141 151

lbs

0.60 0.84 1.58 2.32 3.80 5.53 7.14 9.57 12.32 22.35 30.60 48.00

kg

0.27 0.38 0.72 1.05 1.72 2.51 3.24 4.34 5.59 10.14 13.88 21.77

• Manufactured in accordance with ASTM specification A589. • All sizes are recessed and taper tapped 3⁄4" per foot on diameter. • Sizes over 2" have threads phosphated and outside painted light blue. The electroplated have a light blue band around the center of the coupling.

350 q FIGURE #9 Drive Couplings

Outside Diameter (Coupling)

Size

Length

Unit Weight

NPS

DN

in

mm

in

mm

lbs

kg

11⁄4

32

2.054

52

23⁄4

70

1.00

0.45

11⁄2

40

2.200

56

23⁄4

70

0.84

0.38

2

50

2.875

73

33⁄8

86

2.14

0.97

• All sizes are recessed and taper tapped 3⁄4" per foot on diameter.

379 q FIGURE Shallow Well Couplings

Outside Diameter (Coupling)

Size

Length

Unit Weight

NPS

DN

in

mm

in

mm

lbs

kg

11⁄4

32

2.054

52

23⁄4

70

1.03

0.47

11⁄2

40

2.200

56

23⁄4

70

0.90

0.41

2

50

2.875

73

27⁄8

73

1.86

0.84

• The 1 1⁄4" are straight rapped and recessed. • The 1 1⁄2 and 2" are taper tapped 3⁄4" per foot on diameter and recessed. • The 2" threads are electroplated. PROJECT INFORMATION

APPROVAL STAMP

Contractor:

q Approved q Approved as noted q Not approved

Engineer:

Remarks:

Project: Address:

Submittal Date: Notes 1: Notes 2: PF-11.16

PIPE NIPPLES General Assembly of Threaded Fittings 1) Inspect both male and female components prior to assembly. • Threads should be free from mechanical damage, dirt, chips and excess cutting oil. • Clean or replace components as necessary. 2) Application of thread sealant • Use a thread sealant that is fast drying, sets-up to a semi hard condition and is vibration resistant. Alternately, an anaerobic sealant may be utilized. • Thoroughly mix the thread sealant prior to application. • Apply a thick even coat to the male threads only. Best application is achieved with a brush stiff enough to force sealant down to the root of the threads. 3) Joint Makeup • For sizes up to and including 2" pipe, wrench tight makeup is considered three full turns past handtight. Handtight engagement for 1⁄2" through 2" thread varies from 41⁄2 turns to 5 turns. • For 2 1⁄2" through 4" sizes, wrench tight makeup is considered two full turns past handtight. Handtight engagement for 2 1⁄2" through 4" thread varies from 51⁄2 turns to 63⁄4 turns.

PF-11.13

Recommend Documents
Best application is achieved with a brush stiff enough to force sealant down ... For sizes up to and including 2" pipe, wrench tight makeup is considered three full ...

Manufactured in accordance with ASTM specification A589. • All sizes are recessed and taper tapped 3⁄4" per foot on diameter. • Sizes over 2" have threads phosphated and outside painted light blue. The electroplated have a light blue band aroun

to the root of the threads. 3) Joint Makeup. • For sizes up to and including 2" pipe, wrench tight makeup is considered three full turns past handtight. Handtight engagement for 1⁄2" through 2" thread varies from 41⁄2 turns to 5 turns. • For

PROJECT INFORMATION. APPROVAL STAMP. Project: q Approved. Address: q Approved as noted. Contractor: q Not approved. Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PIPE COUPLINGS. Steel Pipe Couplings - Merchant Couplings. FIGURE 336. Standard,

Project: q Approved. Address: q Approved as noted. Contractor: q Not approved. Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PIPE COUPLINGS. Steel Pipe Couplings - Merchant Couplings. FIGURE 337. Extra Strong (XS), q Full & q Half. Size. Outsi

PROJECT INFORMATION. APPROVAL STAMP. Project: q Approved. Address: q Approved as noted. Contractor: q Not approved. Engineer: Remarks: Submittal Date: Notes 1: Notes 2: PIPE COUPLINGS. Steel Pipe Couplings. FIGURE 348. API LIne Pipe Couplings. Size.

Mar 12, 2012 - (Inches). Threads per Inch. Black. Galv. Black. Galv. Straight Tapped. Taper Tapped. 1⁄8. $103.13. $125.96. $355.97. $384.21. 3.00. 100. 0.563.

Feb 4, 2008 - Go to Anvil's Web site for the most current list .... Unless otherwise specified, the above will be furnished Black Non-Recessed. • All sizes are ...

delivery, to arrange for prompt inspection of the damaged goods. ..... Unless otherwise specified, 1/8" - 2" Straight Tapped Couplings will be supplied. • All sizes ...

Dec 4, 2017 - All sizes of couplings will be furnished raw (mill coating) unless otherwise specified. All couplings are dipped in rust inhibitor. If specified, sizes 21/2"–6" may be ordered with phosphate coating. • API Line Pipe Couplings are fu