PISCO BRASS NEEDLE VALVE
Flow Control Valve for use in Environments of High Heat and Spatters
Throttle (Needle) Valve
Brass The products listed in this page are ECO-friendly products.
Characteristics
* Please refer to page 4 for the details of ECO-friendly products.
With cover
øD
T
No cover
KJNCøD-T-
KJNCøD-T-1-
KJNC4-M5-
KJNC4-M5-1-
KJNC4-01-
KJNC4-01-1-
KJNC6-M5-
KJNC6-M5-1-
KJNC6-01-
KJNC6-01-1-
Fluid medium
Air, water *¹ *²
KJNC6-02-
KJNC6-02-1-
Max. operating pressure
150psi (1MPa)
KJNC6-03-
KJNC6-03-1-
KJNC8-01-
KJNC8-01-1-
KJNC8-02-
KJNC8-02-1-
KJNC8-03-
KJNC8-03-1-
KJNC10-02-
KJNC10-02-1-
KJNC10-03-
KJNC10-03-1-
KJNC10-04-
KJNC10-04-1-
KJNC12-03-
KJNC12-03-1-
KJNC12-04-
KJNC12-04-1-
-100kPa Operating temp. range HNBR: 32 ~ 212°F (0 ~ 100°C) NBR*³: 32 ~ 140°F (0 ~ 60°C) FKM*³: 32 ~ 248°F (0 ~ 120°C) Max. vacuum
*1. When using water, please limit the level of surge pressure to the maximum operating pressure or less. *2. When using water, please make sure to use insert-ring. There is a possiblity of becoming the cause of breakage, leakage, or tube escape. *3. Sealing Material: NBR and FKM are prepared as options.
Construction (1)
No (12)
(3) Thread body
(6)
nickel-plated brass
(4) Elastic sleeve HNBR *¹
Caution
(6) Tube
Spatter tube
(7) Cover
nickel-plated brass
* The model with low sales average may be build to order production. For details, please contact Pisco sales ofce or sales representative.
(8) Guide ring
nickel-plated brass
(9) Lock claws
stainless steel
(10) O-ring
HNBR *¹
(11) Metallic body
nickel-plated brass
(12) Needle
nickel-plated brass
Model Designation (Example) (1)
(2) (3)
Detailed Safety Instructions
01 (4)
(5)
Before using the PISCO device, be sure to read the "Safety Instructions", "Common Safety Instructions for Products Listed in This Manual" on page 13 to 15 and "Common Safety Instructions for Controllers" on page 64.
(6)
(1) All Metal (Brass) Throttle Valve (2) Type (3) Tube dia. (øD) mm size (mm) Code
4
6
8
10
12
Dia.
ø4
ø6
ø8
ø10
ø12
(4) Thread size (T) Metric thread
Taper pipe thread
Code
M5
01
02
03
04
size
M5×0.8
R1/8
R1/4
R3/8
R1/2
(5) Cover option 1: No cover No code: With cover
(6) Seal rubber material No code: HNBR F: FKM N: NBR
, please select a seal rubber material.
nickel-plated brass
(9) (8) Heat proof sealock-coated
KJN C 6
*1. For
(5) Release ring (10)
*1. FKM or NBR can be selected. *2. The gasket material of M thread is as follows. HNBR spec.: SUS316 + FKM FKM spec.: SUS316 + FKM NBR spec.: SUS304 + NBR
1 pc. in a bag
Option
Vacuum
(5)
nickel-plated brass
Warnings : 1. Adjust the flow rate by opening the needle gradually from the fully closed position. With the needle open, there are chances of the device flying out. Turn the needle clockwise to close or counterclockwise to open. 2. When adjusting the air ow of equipment, open the needle gradually from the fully closed position. With the needle open, large ow may be applied to the equipment instantly and causes damage to the equipment. 3. When the fluid admitted is water or other liquids, use an insert ring. Otherwise the tube may fall out to cause leakage. 4. When the fluid admitted is water or other liquids, limit the level of surge pressure to the maximum working pressure or less. 5. Although the metal body can rotate against its thread body, avoid continuous and forcible swinging and rotation. Otherwise the body may suffer damage or develop leakage. 6. When the products are used under high temperature, choose seal materials with enough safety factor. Since seal material may cause air leakage due to heat deterioration, please conduct periodical maintenance. When an air leakage is found, change the products as soon as possible. 7. After opening the package, do not mix products with different type of seal materials. It may cause unintentional accidents. Cautions : 1. The Throttle (Needle) Valve is designed to tolerate some air ow at fully closed position. Therefore do not use it for applications that permits no air ow. 2. When you use a covered tube, be sure to cut the covering into the specied dimensions (see below) before use. Failure to do so may result in the coming off of the tube, leakage or inability to connect the tube. Tube dia. ø4mm ø6mm ø8mm ø10mm ø12mm Spatter Tube Cover cutting 15.5mm 16.5mm 17.5mm 20.0mm 23.5mm (Covered Tube) Dimension (C) (0.61in.) (0.65in.) (0.69in.) (0.79in.) (0.92in.)
C
Actuator
(11)
nickel-plated brass
(2) Lock nut
Tube
(7)
(1) Knob
Plarailchain
(4)
Material
Robot Parts
(2) (3)
Parts
Control
Specifications
Model
KJNC Elbow
Valve
A new line-up of flow control equipment best suitable for high heat and spatter environments. HNBR is used for seal material. NBR and FKM specifications are also available as order producion.
75
Products
3,6&286$,1&
29(56($60$5.(7,1*'(3$570(17
::5,*+7:22'$9((/0+8567,/86$ 7(/ )$; :HEVLWH ZZZSLVFRFRP(PDLO LQTXLU\#SLVFRFRP
0,1$0,0,12:$.$0,,1$1$*$1235() -$3$1 7(/ )$; :HEVLWH ZZZSLVFRFRMSHQJOLVKSLVFRKWP(PDLO LQWO#SLVFRFRMS
1,+213,6&26,1*$325(37(/7'
+($'2)),&($1'3/$17
%/.$1*02.,2$9(18(7(&+3/$&(6,1*$325( 7(/ )$; :HEVLWH ZZZSLVFRFRPVJ(PDLO SLVFR#SDFLÀFQHWVJ
,=8+$
Throttle (Needle) Valve
Brass The products listed in this page are ECO-friendly products.
Characteristics
* Please refer to page 4 for the details of ECO-friendly products.
With cover
øD
T
No cover
KJNCøD-T-
KJNCøD-T-1-
KJNC4-M5-
KJNC4-M5-1-
KJNC4-01-
KJNC4-01-1-
KJNC6-M5-
KJNC6-M5-1-
KJNC6-01-
KJNC6-01-1-
Fluid medium
Air, water *¹ *²
KJNC6-02-
KJNC6-02-1-
Max. operating pressure
150psi (1MPa)
KJNC6-03-
KJNC6-03-1-
KJNC8-01-
KJNC8-01-1-
KJNC8-02-
KJNC8-02-1-
KJNC8-03-
KJNC8-03-1-
KJNC10-02-
KJNC10-02-1-
KJNC10-03-
KJNC10-03-1-
KJNC10-04-
KJNC10-04-1-
KJNC12-03-
KJNC12-03-1-
KJNC12-04-
KJNC12-04-1-
-100kPa Operating temp. range HNBR: 32 ~ 212°F (0 ~ 100°C) NBR*³: 32 ~ 140°F (0 ~ 60°C) FKM*³: 32 ~ 248°F (0 ~ 120°C) Max. vacuum
*1. When using water, please limit the level of surge pressure to the maximum operating pressure or less. *2. When using water, please make sure to use insert-ring. There is a possiblity of becoming the cause of breakage, leakage, or tube escape. *3. Sealing Material: NBR and FKM are prepared as options.
Construction (1)
No (12)
(3) Thread body
(6)
nickel-plated brass
(4) Elastic sleeve HNBR *¹
Caution
(6) Tube
Spatter tube
(7) Cover
nickel-plated brass
* The model with low sales average may be build to order production. For details, please contact Pisco sales ofce or sales representative.
(8) Guide ring
nickel-plated brass
(9) Lock claws
stainless steel
(10) O-ring
HNBR *¹
(11) Metallic body
nickel-plated brass
(12) Needle
nickel-plated brass
Model Designation (Example) (1)
(2) (3)
Detailed Safety Instructions
01 (4)
(5)
Before using the PISCO device, be sure to read the "Safety Instructions", "Common Safety Instructions for Products Listed in This Manual" on page 13 to 15 and "Common Safety Instructions for Controllers" on page 64.
(6)
(1) All Metal (Brass) Throttle Valve (2) Type (3) Tube dia. (øD) mm size (mm) Code
4
6
8
10
12
Dia.
ø4
ø6
ø8
ø10
ø12
(4) Thread size (T) Metric thread
Taper pipe thread
Code
M5
01
02
03
04
size
M5×0.8
R1/8
R1/4
R3/8
R1/2
(5) Cover option 1: No cover No code: With cover
(6) Seal rubber material No code: HNBR F: FKM N: NBR
, please select a seal rubber material.
nickel-plated brass
(9) (8) Heat proof sealock-coated
KJN C 6
*1. For
(5) Release ring (10)
*1. FKM or NBR can be selected. *2. The gasket material of M thread is as follows. HNBR spec.: SUS316 + FKM FKM spec.: SUS316 + FKM NBR spec.: SUS304 + NBR
1 pc. in a bag
Option
Vacuum
(5)
nickel-plated brass
Warnings : 1. Adjust the flow rate by opening the needle gradually from the fully closed position. With the needle open, there are chances of the device flying out. Turn the needle clockwise to close or counterclockwise to open. 2. When adjusting the air ow of equipment, open the needle gradually from the fully closed position. With the needle open, large ow may be applied to the equipment instantly and causes damage to the equipment. 3. When the fluid admitted is water or other liquids, use an insert ring. Otherwise the tube may fall out to cause leakage. 4. When the fluid admitted is water or other liquids, limit the level of surge pressure to the maximum working pressure or less. 5. Although the metal body can rotate against its thread body, avoid continuous and forcible swinging and rotation. Otherwise the body may suffer damage or develop leakage. 6. When the products are used under high temperature, choose seal materials with enough safety factor. Since seal material may cause air leakage due to heat deterioration, please conduct periodical maintenance. When an air leakage is found, change the products as soon as possible. 7. After opening the package, do not mix products with different type of seal materials. It may cause unintentional accidents. Cautions : 1. The Throttle (Needle) Valve is designed to tolerate some air ow at fully closed position. Therefore do not use it for applications that permits no air ow. 2. When you use a covered tube, be sure to cut the covering into the specied dimensions (see below) before use. Failure to do so may result in the coming off of the tube, leakage or inability to connect the tube. Tube dia. ø4mm ø6mm ø8mm ø10mm ø12mm Spatter Tube Cover cutting 15.5mm 16.5mm 17.5mm 20.0mm 23.5mm (Covered Tube) Dimension (C) (0.61in.) (0.65in.) (0.69in.) (0.79in.) (0.92in.)
C
Actuator
(11)
nickel-plated brass
(2) Lock nut
Tube
(7)
(1) Knob
Plarailchain
(4)
Material
Robot Parts
(2) (3)
Parts
Control
Specifications
Model
KJNC Elbow
Valve
A new line-up of flow control equipment best suitable for high heat and spatter environments. HNBR is used for seal material. NBR and FKM specifications are also available as order producion.
75
Products
3,6&286$,1&
29(56($60$5.(7,1*'(3$570(17
::5,*+7:22'$9((/0+8567,/86$ 7(/ )$; :HEVLWH ZZZSLVFRFRP(PDLO LQTXLU\#SLVFRFRP
0,1$0,0,12:$.$0,,1$1$*$1235() -$3$1 7(/ )$; :HEVLWH ZZZSLVFRFRMSHQJOLVKSLVFRKWP(PDLO LQWO#SLVFRFRMS
1,+213,6&26,1*$325(37(/7'
+($'2)),&($1'3/$17
%/.$1*02.,2$9(18(7(&+3/$&(6,1*$325( 7(/ )$; :HEVLWH ZZZSLVFRFRPVJ(PDLO SLVFR#SDFLÀFQHWVJ
,=8+$
