PMAG installation Sealed aluminum and stainless ... AWS
Sealed aluminum and stainless steel mag installation
THE ULTIMATE BULLET BUTTON TOOL
KIT B 4 PACK (PMAG) “PATENT PENDING”
.223-5.56
All UBBT products are 100% guaranteed to be free of material and workmanship defects and can be returned no questions asked. (We recommend contacting us for technical assistance before returning items). Email us at: [email protected] Buyer is responsible for shipping costs on returns. Any defective items that are NOT manufactured by Thordsen Customs will be replaced or refunded at our discretion. Thordsen Customs assumes that our products will be used in a manner consistent with California state law and WILL NOT be held liable for ANY misuse of our products.
1. 2.
3.
Drill a 3/32" hole through the front face of magazine 3/16” from bottom center. FIG 1 Using a torx wrench on a drill, with a LOT of pressure, drive ¼” cap screw into hole keeping it square (FIG 2). The screw will bite into the metal and form its own threads. It will be very tight at first, but will get easier. Screw assembly (FIG 3) onto mag and tighten with ¼” socket wrench until snug. (Loctite is recommended) DO NOT USE PLIERS OR OVER TIGHTEN.
NOTE: The torx screw is intended for use with ALUMINUM mags only. To install on Stainless steel mags, use a #43 drill for step 1 and a 4-40 tap for step 2.
PMAG installation 1. 2.
3. 4.
Drill a 3/32" hole through the front face of magazine, keeping it square. (FIG 1 and 2) Using the .05 allen wrench supplied with kit, with a little pressure, turn ½” set screw into hole (FIG 2). The screw will bite into the plastic and form its own threads. It will be very tight at first, but will get easier. Remove screw once it feels easy to turn. Screw assembly (FIG 3) onto PMAG and tighten with ¼” socket wrench until snug. DO NOT USE PLIERS OR OVER TIGHTEN.
Copyright 2011 Thordsen Customs LLC
Copyright 2011 Thordsen Customs LLC
THE ULTIMATE BULLET BUTTON TOOL
KIT B 4 PACK (PMAG) “PATENT PENDING”
.223-5.56
All UBBT products are 100% guaranteed to be free of material and workmanship defects and can be returned no questions asked. (We recommend contacting us for technical assistance before returning items). Email us at: [email protected] Buyer is responsible for shipping costs on returns. Any defective items that are NOT manufactured by Thordsen Customs will be replaced or refunded at our discretion. Thordsen Customs assumes that our products will be used in a manner consistent with California state law and WILL NOT be held liable for ANY misuse of our products.
1. 2.
3.
Drill a 3/32" hole through the front face of magazine 3/16” from bottom center. FIG 1 Using a torx wrench on a drill, with a LOT of pressure, drive ¼” cap screw into hole keeping it square (FIG 2). The screw will bite into the metal and form its own threads. It will be very tight at first, but will get easier. Screw assembly (FIG 3) onto mag and tighten with ¼” socket wrench until snug. (Loctite is recommended) DO NOT USE PLIERS OR OVER TIGHTEN.
NOTE: The torx screw is intended for use with ALUMINUM mags only. To install on Stainless steel mags, use a #43 drill for step 1 and a 4-40 tap for step 2.
PMAG installation 1. 2.
3. 4.
Drill a 3/32" hole through the front face of magazine, keeping it square. (FIG 1 and 2) Using the .05 allen wrench supplied with kit, with a little pressure, turn ½” set screw into hole (FIG 2). The screw will bite into the plastic and form its own threads. It will be very tight at first, but will get easier. Remove screw once it feels easy to turn. Screw assembly (FIG 3) onto PMAG and tighten with ¼” socket wrench until snug. DO NOT USE PLIERS OR OVER TIGHTEN.
Copyright 2011 Thordsen Customs LLC
Copyright 2011 Thordsen Customs LLC
