RBC008 Tow ball Mount Bike Carrier instructions | Rhino-Rack
CONTROLLED
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) Important:
Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies. Place these instructions in the vehicle’s glove box after installation is complete.
Layout
! NOT RECOMMENDED FOR OFF ROAD USE
Important Information Please remove bike rack when putting vehicle through an automatic car wash. Note for Dealers and Fitters It is your responsibility to ensure this fitting instruction is given to the end user or client Rhino-Rack 3 Pike Street, Rydalmere, NSW 2116, Australia. (Ph) (02) 9638 4744 (Fax) (02) 9638 4822
Document No: RR236 Prepared By: Andy Wana Authorised By: Gary England
Fit Time 10min Issue No: 05 Issue Date: 29/01/2016
These instructions remain the property of Rhino-Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended.
Page 1 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) Parts List Item
Component Name
Qty
1
Bike Rack
1
2
Keys
1
3
Tie Down Straps
2
4
Spanner
1
5
Fastener Set
1
6
Fitting Instruction
1
RBC007
RBC008
Carry up to 3 bicycles ONLY
Carry up to 4 bicycles ONLY
1 2 3 4 x1
5
x1 x1
Load capacity up to 45kg ONLY
1
2
A
B
Page 2 of 7
Load capacity up to 60kg ONLY
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) 3
4
5
Tighten the dial knob
Note
Bike Carrier can be fit to euro style ball mounts. Be Sure the Mount is clean and free of grease before installing.
Page 3 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) 6
7
Use the supplied spanner to tighten the rack in place.
Use the supplied cover to protect the dial knob.
Step 1 : Undo the locking bolt as shown (Fastener set - item 5) Step 2 + 3 : Wedge the spacer and insert pin as shown Step 4 : Insert locking pin Step 5 : Place pole in upright position, insert locking bolt and tighten
2
x1
1
x1 x1
3
4 5
4 Page 4 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) 8
Place bicycles as shown on the left. Note the direction each bicycle is facing when mounted on the rack.
! Always start to load the bicycle from the inside
9
Tighten cradle
Page 5 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) 10
! Secure bikes to bike carrier with supplied straps to avoid movement
11
12
Page 6 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) Note
When the carrier is fitted to a euro style tow mount, loop the straps through the bike frame both front and rear. Tie these straps off towards the outer edges of the vehicle. This will prevent any swivel when in use.
Top View: Tie off the bike frame at suitable locations towards the outer edge of the vehicle.
Straps must be tight front and rear.
13
Tie off points will vary vehicle to vehicle. Be sure they are secure before use.
Tilt the bike rack as shown for access to tailgate when rack is in use.
Page 7 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) Important:
Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies. Place these instructions in the vehicle’s glove box after installation is complete.
Layout
! NOT RECOMMENDED FOR OFF ROAD USE
Important Information Please remove bike rack when putting vehicle through an automatic car wash. Note for Dealers and Fitters It is your responsibility to ensure this fitting instruction is given to the end user or client Rhino-Rack 3 Pike Street, Rydalmere, NSW 2116, Australia. (Ph) (02) 9638 4744 (Fax) (02) 9638 4822
Document No: RR236 Prepared By: Andy Wana Authorised By: Gary England
Fit Time 10min Issue No: 05 Issue Date: 29/01/2016
These instructions remain the property of Rhino-Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended.
Page 1 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) Parts List Item
Component Name
Qty
1
Bike Rack
1
2
Keys
1
3
Tie Down Straps
2
4
Spanner
1
5
Fastener Set
1
6
Fitting Instruction
1
RBC007
RBC008
Carry up to 3 bicycles ONLY
Carry up to 4 bicycles ONLY
1 2 3 4 x1
5
x1 x1
Load capacity up to 45kg ONLY
1
2
A
B
Page 2 of 7
Load capacity up to 60kg ONLY
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) 3
4
5
Tighten the dial knob
Note
Bike Carrier can be fit to euro style ball mounts. Be Sure the Mount is clean and free of grease before installing.
Page 3 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) 6
7
Use the supplied spanner to tighten the rack in place.
Use the supplied cover to protect the dial knob.
Step 1 : Undo the locking bolt as shown (Fastener set - item 5) Step 2 + 3 : Wedge the spacer and insert pin as shown Step 4 : Insert locking pin Step 5 : Place pole in upright position, insert locking bolt and tighten
2
x1
1
x1 x1
3
4 5
4 Page 4 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) 8
Place bicycles as shown on the left. Note the direction each bicycle is facing when mounted on the rack.
! Always start to load the bicycle from the inside
9
Tighten cradle
Page 5 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) 10
! Secure bikes to bike carrier with supplied straps to avoid movement
11
12
Page 6 of 7
Rhino-Rack 3 Bike Carrier Ball Mount (RBC007) Rhino-Rack 4 Bike Carrier Ball Mount (RBC008) Note
When the carrier is fitted to a euro style tow mount, loop the straps through the bike frame both front and rear. Tie these straps off towards the outer edges of the vehicle. This will prevent any swivel when in use.
Top View: Tie off the bike frame at suitable locations towards the outer edge of the vehicle.
Straps must be tight front and rear.
13
Tie off points will vary vehicle to vehicle. Be sure they are secure before use.
Tilt the bike rack as shown for access to tailgate when rack is in use.
Page 7 of 7
